You have the liberty to manage device connection on your own.

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

Intermittent internet connection using LAN cable
Looks like there is something wrong with your service connection.Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.


Intermittent internet connection using Wi-Fi

1. Router Positioning

Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.    

i) High vs. Low

Put the router as high up as possible to extend the broadcasting range  of the radio waves. This also helps clear the router of possible interferences.
 

ii) Concrete & Metals

Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost  impossible for Wi-Fi signals to penetrate.
 

iii) Distance to Router

The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your  devices as possible, but this is only practical if you have one main area where you tend to use your devices.

Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.

2. Wireless Interference & Noise

You've probably never noticed but there are wireless signals all around you wherever you go and they're passing  through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.

Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:

• Microwaves
• Bluetooth Devices
• Cordless Phone

3.  Surrounding Wi-Fi signals

A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many routers within close proximity.

Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.
 

4. Usage

More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultra box/ Netflix.

Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem  persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file)  before submitting the form.

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

No, if you already have an Ulti box you will not be required to swap the box to enjoy the new packs. However, if you would like to access 4K UHD content, you may upgrade to Ultra Box. Installation and activation fees will be chargeable depending on your package selection.

No, Pay-Per-View is no longer available in CH200.

1. Please standby  computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.254 and below page  will appear.

If below box appear, please enter required details:

USERNAME: Administrator

PASSWORD: (ACCESS KEY AT THE RGW STICKER)

(These are the defaults, if you have done previous configuration on your router the password may be different)

4. Once enter into the page "'TECHNICOLOR TG784N V3'', you may follow below steps to get the best wireless channel information.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. In order to get the best wireless channel, click "Wireless Scan" to scan available surroundings wireless Channel.

D. Please choose channel with lesser number of usage.

Example in below case, you may choose channel 4.

5. To configure wireless channel, please proceed with below steps.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. Then, click "Configure" to change the channel selection (automatic to manual) and other configuration option.

D. Please ensure below items:

i. WLAN Enable: Tick

ii. Interface Enable: Tick

iii. Change the Channel Selection to Manual

iv. Change the wireless Channel based on Step 4(D).

v. Once completed the selection, click the "Apply" button.

Starting 1 April 2024, Astro’s Chinese content offering on our Primary & Family Pack is now bigger than ever with the addition of up to 10 channels featuring the latest Chinese primetime dramas, variety and current affairs programmes as well as great selection of movies and musical shows. These are the channels available in the Primary & Family Pack at no additional cost:

• Celestial Movies (CH309)
• TVB Jade (CH310)
• Astro AOD (CH311)
• TVB Entertainment News (CH317)
• TVB Xing He (CH319)
• TVBS Asia (CH320)
• NHK World (CH398)

Starting 28 April 2022, Astro customers can access Disney+ Hotstar via Ultra Box, mobile app and website. We are working towards making Disney+ Hotstar available via the Ulti Box. Stay tuned for updates.

â€

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)
 

Username: admin
Password: admin (or time123)

 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

• On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab

• Please ensure Wireless RF Mode is Enabled.

• Click the drop-down arrow for Channel, then select your desired channel.
• Choose between 1 until 11 (Suggested 1,6,11).

• Click Submit. Router will auto reboot and connection re-establish after few minutes.

Disney+ Hotstar is available to Astro customers on the Disney+ Hotstar app on Android and iOS devices and website (DisneyPlusHotstar.my) which is accessible on tablets and connected TVs. Unfortunately, Disney+ Hotstar is not available on Astro GO. However, customers can enjoy it on the big screen via the Ultra or Ulti Box. 

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please ensure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Intermittent internet connection using Wi-Fi
1. Router Positioning

Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day  and night.

  i) High vs. Low

     Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.

  ii) Concrete & Metals

      Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also,       avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which       can be almost impossible for Wi-Fi signals to penetrate.

  iii) Distance to Router

      The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.

Otherwise, you should place your  router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.

2. Wireless Interference & Noise

You've probably never  noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices,  Wi-Fi routers, satellites, cell towers, and more.

Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:

i) Microwaves
ii) Bluetooth Devices
iii) Cordless Phone

3.  Surrounding Wi-Fi signals

A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially  problematic in housing complexes and apartments where there can be many routers within close proximity.

Which is why it's important that you pick  a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

4. Usage

More likely, however, is that the people  on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/ Netflix.

Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in  your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document,  PDF, Image file) before submitting the form.

Quick Info
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

Yes, customers will be charged 8% Service Tax on switching fee for any services rendered on or after 1st March 2024.
 

You must subscribe to an Astro subscription (NJOI customers are not eligible) in order to get the Ulti Box. 

‍

The eligibility criteria for the Ulti Box are as follows:

New Customers

All new Astro customers with a monthly subscription fee of below RM100 will be entitled to select the Ulti Box upon signing up for Astro’s packages. 

‍

Existing Customers (Box Upgrade for Primary or Multiroom)

Existing customers are required to have an internet connection at home with a recommended internet speed of 10Mbps and above in order to upgrade your existing box to Ulti Box. 

Note: 

·      Existing Ultra Box customers are not eligible for a swap to the Ulti Box.

·      If your existing box is a PVR, you will lose access to all the recordings stored in the PVR

‍

Multiroom (New subscription)

Customers subscribing for an additional multiroom subscription are entitled to select the Ulti Box as part of the subscription.

Currently, Maxis, Digi, Celcom, TuneTalk, U-Mobile, Yes, XOX and Webe.

No, you will not be charged 8% Service Tax for paper billing option.

No, the Service Tax is a tax payable entirely to the Government. Astro acts as a collection agent for the Government.
 

Of course not! It is a value-added service introduced for your convenience.

We encourage customers to ensure their TV compatibility with the Astro Multiroom (Smart TV) app first before making any purchase here.

If you are still experiencing any issues, please contact us at wecare@astro.com.my or call or WhatsApp us at 03-9543 3838 and our agents will be happy to assist you.

This Service Tax is imposed on customers of Pay TV broadcasting services by the Government. As such the Service Tax will be passed on to the customers.
 

You would have to create a new Astro ID with your email address or mobile number and link your Astro subscription. Please follow the steps in the link here

New and existing Astro customers will enjoy rebates up to RM39/month for 24 months when they subscribe to selected Astro Fibre TV bundles and a FREE speed upgrade for all customers who subscribe within the promotion period.
 

Step 1:
Type ASTRO<space>BAL<space>10-Digit Astro Account No. 
Example: ASTRO BAL 08XXXXXXXX

*Standard telco charges and Terms and Conditions apply

Step 2:
Send SMS to 66688

Please ensure that you have subscribed to the mentioned channel.
If you're subscribed to this channel, follow below steps.

STEP 1
You need to refresh the signal on your box.
Refer to Refresh signal of your box guide.

STEP 2
If issue persist after 30 minutes, proceed to submit report via WhatsApp or Feedback Form.

Upon successful subscription, you will be able to view your chosen HD channels within 3 hours by keying in the channel numbers into your remote control. Please note that subscription through Channel 200 will take effect within 24 hours.

We would recommend the following browsers for a smooth verification process:

• Google Chrome

• Microsoft Edge

• Mozilla Firefox

• Safari

The new packs and access to Netflix on the Ultra Box and Ulti Box is available for Astro IPTV customers.

This convenient option allows you to complete your registration without the need to provide hard copy documents physically to the sales agent. The identity verification process helps to secure your Account and protect it from unauthorised usage.

Please make sure that:

• You are inserting the correct account holder's information while linking, ie: I/C number, passport number, Astro account number or Smart card number.
• You are linking to an Astro account (NJOI customers will not be able to log into Astro GO).
• Your Astro account is not currently linked to any other Astro ID. If your Astro account is currently linked to another Astro ID, you will see a red notice.

To find out which Astro ID is currently linked to your account, you may submit a feedback form. Kindly select feedback type "I have an enquiry/issue with Apps

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3    

Navigate to HDMI Audio and press "OK".

STEP 4  

Navigate to your preferred selection and press “OK”.

The RM15 monthly rebate (before Govt. Tax) will be applicable to all on-going Multiroom Smart TV subscriptions until further notice. However, in the event of rebate expiry, Astro will notify impacted customers in advance via email or SMS. To update your contact details, please reach out via a feedback form here.

No, you are not allowed to change your due date or maintain your old due date. Your current due date is as per Astro Policy. Therefore, to ensure that you continue to enjoy uninterrupted services, we advise you to observe this change in due date from Day 30 to Day 25 and proceed with the necessary payment.