You may proceed with the following troubleshooting steps and it shouldn't take you much longer than 15 min

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Yellow port at Tplink Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to tplinkwifi.net and to access to below login page. Type the Username and  Password, then click "Login".

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your  router previously, the password may be different.

For example, below is the login details of the above router:
 

Username: admin

Password: TIMECE24
 

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, choose Advanced and click the Wireless tab on the left menu. Then, select Wireless Settings from the sub menu. Below screen will appear for 2.4GHz selection.

i. Please ensure to tick Enable Wireless Radio function.

ii. To change the channel, click the  drop-down arrow for Channel, then select your desired channel.

Choose between 1 to 13 (Suggested  channels : 1,6,11). Then, click "Save" for the changes to take place.

iii. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

iv. Next, select 5GHz to make changes on the wireless channel for 5GHz.

v. Click the drop-down arrow for Channel, then select your desired channel from the selection.

vi. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

You may report the incident on WhatsApp at 03-9543 3838 by typing PNP and our access our user guide or request for further help from our dedicated agents. Please have your Airway Bill tracking numbers ready for validation.If a replacement box/Astro SIM card is deemed necessary, a new Box and a new Astro SIM card will be couriered to your service address.

Once your Plug & Play Box has been activated, a courier service will reach out to you within TWO (2) weeks for a time for them to pick up the old Astro box and SIM card/Smartcard.

1. Ensure that all cables have been plugged out of the old Astro box. To remove the white satellite cable from your old Astro box, simply hold the cable, twist, and gently pull.
2. Set aside these items to be ready for our delivery partner to pick up from you:

• Old Astro Box
• Old Astro Smartcard/SIM Card (leave this in your Astro Box)

3. When a courier arrives at your residence, do confirm that they are collecting items on behalf of Astro.
4. Allow the courier to check the serial number of the Astro box.
5. Hand them all the items for return, and you're done!

Starting 12 December 2023, Multiroom Smart TV app customers can enjoy two 4K Ultra HD (4K UHD) channels, namely CH549 Love Nature and CH805 Astro SuperSport. “Love Nature” is available to all customers regardless of their subscribed TV Pack. It celebrates the complexity of life on earth, presenting nature stories in stunning detail and colours.


Additionally, “Astro SuperSport” is only available to customers on the Sports, Sports Plus, Premium 1, Premium 2, Premium 4, Platinum Lite and Platinum Packs. This channel showcases a variety of sporting events, selected to appeal to the Malaysian viewing audience.

A deposit of RM500 is payable for new subscribers (non-Malaysians). The fee will be refunded when service is terminated.

No deposit is required for all existing Astro customers and new subscribers (Malaysians).

By keying in the 10-digit account number, Astro will be able to provide better self-service options, as it allows Astro to customise automation options based on the needs of each customer's account.

The all-new Astro Fibre is Astro's own internet service whereby customers would be able to enjoy the Astro content over the internet via wireless connection along with high-speed internet service ranging from 50Mbps - 800Mbps.

While Astro & Broadband offers Astro content in partnership with Maxis Fibre Broadband or Allo City Broadband for customers to enjoy the best entertainment through Astro while staying connected with high-speed internet.

Please rest assured that streamingapps labelled with "coming soon" 

will be available on Astro in the near future.Please visit product.astro.com.my/appsfor more information on the streaming apps available on Astro or follow oursocial media to get notified on latest launches. 

Facebook: @Astro 
Instagram: @astromalaysia 
Twitter: @astroonline 

Kindly take note that streaming appslabelled with “coming soon” will be made available on Astro once they areready. Astro reserves the right to delay or cancel streaming app launches, ifnecessary.

All Astro customers and non-customers who have an Astro ID will no longer be able to log in to our digital platforms using their usernames. Users will experience this change if they currently do not use an email address or mobile number to login, for example: johndoe2023.

Currently, you may only add a maximum of five family members to the Astro Fibre App. However, kindly note that we are working on allowing users to add more family members in the future.

We are thrilled to announce that as part of your subscription, you are able to enjoy exclusive coverage of live matches in HD on Astro channels, On Demand and Astro GO! This means that you'll have access to all the latest games, highlights, and analysis, right at your fingertips.

With this new addition, you'll be able to follow your favourite teams and players closer than ever before, keeping you up-to-date with all the action on and off the field. Whether you're a die-hard fan or a casual spectator, this new content is sure to provide you with endless hours of entertainment.

To ensure that we continue offering the best choice in sports content, our Sports Pack will now be priced at RM104.99/month (for 12 months contract) or RM99.99/month (for 24 months contract) and Premium Pack 1 will now be priced at RM139.99/month (for 12 months contract) or RM129.99/month (for 24 months contract) starting 9 February 2023, and this applies to all new customers. 

Note that there will no changes for existing Sports Pack & Premium 1 customers in 24 or 12 month contract being renewed before 1st June 2023.

We appreciate your continued support and can't wait for you to experience this exciting new addition to your Sports Pack subscription.

Please refer to the table below for the full revised pricing for the following packs:

We hope you continue to enjoy your Astro experience with us.
 

Please use your Astro ID that was registered with your Astro Fibre subscription to log in to the Astro Fibre App.

The matches will be available on the channels Astro Arena Bola (CH803) and Astro Arena Bola 2 (CH804), On Demand and Astro GO.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the blue port in Cisco Router and direct to computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

‍

‍

4. Type the Username and Password as below. Then click "OK". (These are the defaults, if you have done previous configuration on your router the password may be different).

Username: admin

Password: admin (or time123)

5. Click "OK" when a Warning prompt that says,” Using this advanced utility to change your router settings could disable your network” appears. Below display will appears.

6. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

7. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

8. Click Wireless Security to view the security settings of your wireless network. Take note of the Security Mode and the Passphrase.

For the example below, the Security Mode used is WPA2/WPA Mixed Mode.

The Wireless name is called Network Name (SSID) and the Passphrase is your wireless password.

‍

9. Now that you have the Wireless name and Password, you are ready to connect your wireless computers and devices to the network.

10. You may change the Network Name (SSID) and the Passphrase to follow your preferences and please ensure save the changes made. Please reconnect to the new wireless name with the new password once completed.

‍

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which could cause the issue.

3. If issue persists, submit your Feedback Form for further assistance.

Yes, Mesh WiFi add-on is available for both Astro Fibre Bundle and Astro Fibre subscription.

Your existing contracts and corresponding rewards including but not limited to discounts/rebates will be removed with no penalty applied and replaced with the new contracts associated with the new packs. Exception applies to Disney+ Hotstar (3-Month Pack) and Multiroom campaigns in which remaining contract durations will be brought over if the subscription is continued or penalty will be applied upon discontinuation of said subscriptions.

Disney+ Hotstar is available to Astro customers on the Disney+ Hotstar app on Android and iOS devices and website (DisneyPlusHotstar.my) which is accessible on tablets and connected TVs. Unfortunately, Disney+ Hotstar is not available on Astro GO. However, customers can enjoy it on the big screen via the Ultra or Ulti Box. 

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be experiencing this problem.    

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please ensure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Intermittent internet connection using Wi-Fi

1. Router Positioning
   Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
   
    i) High vs. Low
   Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   
   ii) Concrete & Metals
   Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   
   iii) Distance to Router
   The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
   
   Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.
   
    

2. Wireless Interference & Noise
   You've probably never noticed but there are wireless signals all around you wherever you go and they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.
   
   Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:
   i) Microwaves
   ii) Bluetooth Devices
   iii) Cordless Phone
    

3.  Surrounding Wi-Fi signals
   A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel  overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many  routers within close proximity. Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

4. Usage
   More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

Please follow the steps below:

Step 1: Fill in Transfer of Equipment Ownership Form (Part A & Part B)

Step 2: Provide an Undertaking Letter if current account holder deceased or un-contactable. (Note: Copy of death certificate is required if account holder deceased).

Step 3: Provide a copy of new applicant NRIC for Malaysian or copy of passport for non-Malaysian or copy of IMM13 Pass with at least 6 months validity for Refugee. (Note: ASTRO name should be displayed on the top left corner on both sides of the identity card copy).

Step 4: A full payment to be made on any outstanding balance for all related accounts (if any).

Step 5: Submit all documents via feedback form .

Step 6: Customer will expect a call from our validation team (Note: Turnaround time for transfer of equipment ownership is 3-5 working days upon receiving all complete documentation).

Note:

1. There might be a loss of transmission during the processing of transfer equipment ownership, split or merge of equipment.

2. Recorded program will be removed for PVR user.

3. A full payment to be made on any outstanding balance for all related accounts.

4. New account holder agreed to continue the remaining contract from previous owner account (if any).

5. Auto debit will be voided upon acknowledgment of transfer equipment ownership (if any).

Additional requirement for New Owner

Capping of applicant age is 21

Malaysians aged < 26 years old and Non-Malaysian - requires copy of utility bill (Phone, Internet, Water or Electricity)

You do not need to request for a reconnection as our system will detect your payment and process it immediately, provided you paid via a real-time payment channel.

Click here for a full list of our payment channels.

The new packs will be available for existing and new Astro customers starting 9 November 2021.

No, you will not be able to manage your account with the Astro Fibre App. However, you may download the “MyAstro” app on your mobile device now to manage your Astro account in a fast and easy way.

Not to worry, our representative will be contacting you within 24 hours.

No, you are not allowed to change your due date or maintain your old due date. Your current due date is as per Astro Policy. Therefore, to ensure that you continue to enjoy uninterrupted services, we advise you to observe this change in due date from Day 30 to Day 25 and proceed with the necessary payment.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Video Resolution and press “OK”.

STEP 4

Navigate to your preferred selection and press “OK”.

Recommended to select Auto.

STEP 5

Navigate to Save and press "OK" to confirm your selection if able to read the text properly.

Otherwise, navigate to Cancel to revert to previous settings.

Yes, you may cancel your Astro Fibre order before service activation, however, kindly note that there is a cancellation charge of RM212 (inclusive of SST) for any service cancellation done 48 hrs before scheduled appointment.

Kindly note that affected customers will be adequately informed 30 days prior to the implementation via SMS which are sent out in phases (Starting 1 July), with scheduled announcements across WhatsApp, My Astro app, and Astro website.

Please disregard the reminder if payment had been made and do check if you have any outstanding balance on Astro Quick Pay.

Please ensure to put your box on standby mode to refresh the signal.

a. Using IVR
   ​1. Dial 03-95433838 and select you preferred language.
   2. Select Account Related.

   4. Select Refresh Smartcard.

b. Using MyAstro web
  
STEP 1
Go to https://myastro.astro.com.my/ in your web browser.

STEP 2
Keyin your Email / Mobile number and password. Then, press "LOG IN".
 
STEP 3
Click on TV pack.
 

STEP 4
Choose Main Room for the Primary Box; else choose Multiroom (If any).
 

STEP 5
Click on "Refresh" to refresh signal on your box. 

For Main Box      

For Multiroom

STEP 6
After tap the Refresh, below notification will be displayed as below.

For Main Box 

For Multiroom

c. Using My Astro App

STEP 1
Open My Astro App and click "Login".

 

STEP 2
Keyin your Email / Mobile number and password. Then, press "LOG IN".

 

STEP 3
Go to "Account".

 

STEP 4
Scroll down to "TV pack" and click on it.

 

STEP 5
Choose Main Room for the Main Box; else choose Multiroom (If any).

 

STEP 6
Tap on "Refresh" to refresh signal on your box. 

 

STEP 7
After tap the Refresh, below notification will be displayed as below.

 

1. Please use a LAN ethernet cable and connect your computer/ laptop to the back of the Maxis Router.

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox, etc.

3. On the address bar, please go to http://192.168.1.254 and the page below will appear.

    The default login of the router as below. If you have done a configuration on your router and changed your password previously, please use the password you have previously set.
 

    Username: administrator

    Password: Router S/N (Available on the sticker at the back of the router)

4. Once you have successfully login, the router's web-based setup page will appear.

5. From the left menu, select WIRELESS to access the screen below.

6. You may change the Channel selection by scrolling down to the Advanced Setup.

7. To change the channel on 2.4 GHz and 5 GHz, click the drop-down arrow for Channel, then select your desired channel.

Then, click "Apply" for the changes to take  place.

8. A warning box will popup, click "OK" for the changes to take place.

9. Please wait until the connection reestablish.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to Digital Audio and press "OK".

STEP 4    

Choose your preferred selection and press “OK”.

STEP 5    

Select Yes, continue and press "OK" to confirm on the changes.        

Otherwise, select No, go back to cancel.

Having trouble with  your phone line ?

You may proceed to contact dedicated service provider directly - 1 800 8211 23

This issue occurs because  your TV does not support the higher resolution.
 

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.
 

STEP 2

Switch on the power for your box and make sure that the adapter's power light is on.
 

STEP 3

Press the standby button repeatedly after switch on the power.

The Startup Options screen will appear on your TV.

STEP 4

Press "987" to access the Advanced Startup Options menu.

Then, press "1" to initiate a reset setting.

STEP 5

Press "OK" to confirm restore to factory setting.

STEP 6

After the factory setting is restored, TV will turn blank.

Please wait until the box completes initiate setup.

STEP 7

Press "1" to initiate Linux download on the software.

STEP 8

Once completed, the following screen will appear on your TV.

Refer to Installation Setup guide here to complete the setup.

For Residential Astro Pay TV customers: You may change your contract from e.g., 12-month to 24-month without incurring a switching fee or cancellation fee. However, if you change your contract from e.g., 24-month to 12-month, will be charged a cancellation fee accordingly if still within minimum term (contract) period. No switching fee applicable.

STEP 1
Switch off the power for your box and  make sure that the adapter's power light is off.

STEP 2
Locate the Smartcard at the front or right side and gently pull it out make sure that the adapter's power light is off.

STEP 3
Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4
Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5
Switch on the power for your box and make sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 6
Turn on your box. You should no longer be experiencing this problem.
If issue persist, please submit the issue in our Feedback Form and attach a picture of your General tab of the STB Diagnostics  for assistance.

Yes, you can restrict programmes based on the age rating by going to "Settings” > “Parental Controls & Profiles” on your Astro Box and Astro GO app. Alternatively, you may also create a Kids Profile that provides security with a 4-digit PIN to exit and accessibility to kids-friendly channels and On Demand content only.

STEP 1
Switch off the power of your box and make sure that the adapter’s power light is off.


STEP 2
Unplug the HDMI cable from your TV and plug it back in securely to other available HDMI port.


STEP 3
Switch on the power for your box and make  sure that the adapter’s power light is on.
Please wait for 5 minutes.


STEP 4
Turn on your box. Do select the correct TV input.
You should no longer be experiencing this problem. 
​