You can proceed with below BTS if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to Diagnostics and press “OK”.

STEP 5

Refer to the signal strength on your screen.

If it is 65 or higher, please take the screenshot and submit your feedback form.

If it is below 65, please go to Step 6.

STEP 6

Switch off the power for your box and  make sure that the adapter’s power light is off.

STEP 7

Unscrew the satellite cable from the box  and pull it out.

STEP 8

Plug the satellite cable back into the  box and screw it back securely.

STEP 9

Switch on the power for your box and make sure that the adapter’s power light is on. Please wait for 5 minutes.

STEP 10

Turn on your box. You should no longer be experiencing this issue.

If issue persist, please submit the issue on our Feedback Form with error details and attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized  Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

Currently, this change affects SMS bills only. Other SMSs such as (but not limited to) bill reminders, payment notifications, promotional SMSs or technical appointment reminders will still be sent to you if applicable.

Your existing contracts and corresponding rewards including but not limited to discounts/rebates will be removed with no penalty applied and replaced with the new contracts associated with the new packs. Exception applies to Disney+ Hotstar (3-Month Pack) and Multiroom campaigns in which remaining contract durations will be brought over if the subscription is continued or penalty will be applied upon discontinuation of said subscriptions.

Disabling band steering means that there will be two frequency bands available for the users - 2.4GHz and 5GHz.
 

Note: Band Steering is called Dual-band Combination in the router web interface.
 

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).
2. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user
Password: user
 

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi to configure the WiFi parameters.

6. Click on Dual-band Combination button to disable the Band Steering.

7. Set the Wi-Fi name and Wi-Fi Password for both 2.4GHz and 5GHz bands based on your preference. Then click "Apply" for the changes to take place.

8. Kindly ensure to reconnect your WiFi according your new WiFi name and password.

You will only be able to watch Astro GO and/or Multiroom Smart TV on up to 2 devices at the same time as opposed to 4 devices with Astro GO+. 

Your cloud recording storage will also decrease from 1500 hours down to 200 hours. Your stored recordings/downloaded shows that exceed 200 hours will also be removed. 

From 8 October 2021 onwards, Astro will be ceasing the daily passes (e.g. 3, 5, 7 & 30 days passes). Please subscribe to the relevant packs to continue enjoying your favourite content. Stay tuned for more exciting offers. Thank you.

For information about the Disney+ Hotstar app functions and specifications, please visit help.hotstar.com or email disneyplus.my@hotstar.com. 

To continue enjoying your PVR decoder and service, you must maintain a minimum monthly subscription fee of RM60 (not inclusive of the recording fee and Govt. Tax).

If you choose to self-install the Plug& Play Box, then no installation fee will be charged. However, there will be an activation fee (please refer to the table below)

If you choose to have an installer to install the Plug & Play Box, then an installation fee will also apply.

Please follow the steps in Q5, then continue with the steps below:

Connect your PVR to Wi-Fi and enjoy access to our library of Video On Demand. Replay old seasons, catch-up latest episodes of your favourite shows, anytime you want. To connect your PVR, follow the steps below depending on your box type:

(a) Wi-Fi Enabled PVR (DMT5)

·      Press the “Home” button and select “Settings” > “Network” > “Wi-Fi”

·      Allow the PVR to scan Wi-Fi networks available and subsequently choose your home Wi-Fi network > Enter your Wi-Fi password if required

·      Once connected, the icon below will appear on the screen.

‍
      Tip: Use the alpha-numeric keyboard on your Astro Remote to key in your password

·      Press the “Home” button and select “On Demand” to start watching videos on demand!

‍

(b) Non-Wi-Fi Enabled PVR (HD PVR)

There are two ways to connect your HD PVR decoder to your home Wi-Fi
(i) Using the Ethernet (LAN) cable 
 

·       Plug in the LAN cable from your modem into the PVR network port

·       Once connected, the icon below will appear on the screen

·       Press the “Home” button and select “On Demand” to start watching videos on demand!

(ii) Using an Astro Wi-Fi dongle as per shown below

Step 1 - Plugin the Wi-Fi dongle into the front USB part of your PVR decoder.

Step 2 - A prompt will appear stating "Do you wish to connect to a wireless network?", select "Yes, continue."

Step 3 - Once connected, the Wi-Fi icon will appear on the screen. Now you are ready to download and enjoy Astro's on demand entertainment.

Step 4 - Press the “Home” button and select “On Demand” to start watching videos on demand!

*The Wi-Fi dongle is only applicable for the non-Wi-Fi enabled PVR (as per the picture).

Please first ensure Disney+ Hotstar access is included and has been activated as part of your Astro subscription. Once you have completed your activation process, you can enjoy Disney+ Hotstar on the Ultra box with these simple steps:

• Step 1 -Press "Home' on your Astro remote control. On the apps rail, select "Disney+ Hotstar' app > OK > My Account

The entire eKYC verification process may be completed within 5 minutes.

Your existing offers with us will not be affected and will continue until the agreed upon date. 

You must subscribe to an Astro subscription (NJOI customers are not eligible) in order to get the Ulti Box. 

‍

The eligibility criteria for the Ulti Box are as follows:

New Customers

All new Astro customers with a monthly subscription fee of below RM100 will be entitled to select the Ulti Box upon signing up for Astro’s packages. 

‍

Existing Customers (Box Upgrade for Primary or Multiroom)

Existing customers are required to have an internet connection at home with a recommended internet speed of 10Mbps and above in order to upgrade your existing box to Ulti Box. 

Note: 

·      Existing Ultra Box customers are not eligible for a swap to the Ulti Box.

·      If your existing box is a PVR, you will lose access to all the recordings stored in the PVR

‍

Multiroom (New subscription)

Customers subscribing for an additional multiroom subscription are entitled to select the Ulti Box as part of the subscription.

1. Please standby computer/laptop to access to the internet and connection must be via LAN  (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and  direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.1.254 and below page will appear.

The default login of the router as below. If you have done a configuration on your router previously,  the password may be different.

Username: user
Password: Router S/N (Available on the sticker at the back of the router)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the left menu, choose Wireless 2.4GHz  and then click Basic Settings tab on the left menu to access to below screen.

6. You may change the Wireless Network Name (SSID) and the SSID Password to follow your preferences, then click "Save"  for the changes to take place.

Please reconnect to the new wireless name with the new password once completed.

7. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

You may change the Wireless Network Name (SSID) and the SSID Password to follow your preferences for 5GHz by choosing Wireless 5GHz  then click Basic Settings.

Click "Save" for the changes to take  place and reconnect to the new wireless name with the new password once  completed.

You can be assured that your data are safe with us. Astro implemented sufficient security measures to protect customer data and fully comply to Personal Data  Protection Act

Yes, you will need to pay additional RM25 per remaining contract months per unit on top of the standard Broadband penalty fee should you terminate the contract within 24 months.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the  site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.

1. Try loading the site on a different device.

Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.

If the website doesn't load on another  device, the problem is either with the network or the website itself.
 

2. Restart your computer.

Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.
 

3. Try loading the site in a different browser.
 

There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can  load the website.
 

4. Temporarily disable your antivirus program.

Your antivirus software may be interfering with your ability to load certain websites.

Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.
 

5. Reset your modem and router.

Traffic to or from a certain website may be getting tripped up by your  modem or router. Resetting these devices may allow you to access the website again.
 

6. Check your computer's date and time settings.

If your date or time is set incorrectly, you may not be able to  connect to secure (https://) websites.

Check your computer or mobile device's clock to make sure that it is  set to the correct time and date.
 

7. In the event the problem persists, please provide below details for further escalation:

   i. List of websites effected.

   ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.

   iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.

   iv. Run the Ping Test -  Please click here for Ping Test guideline.

Once you've  gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

Yes, the monthly subscription fee will be prorated into your Astro bill.

Ultra Box with Contract:

Astro customers are entitled to a two (2) years manufacturer warranty and Installation warranty. During this period, after-sales service is free of charge. However, when your warranty period is over, all after-sales service is subject to a minimal service charge starting from RM65 inclusive of 8% Service Tax.

Other Decoders/Ultra Box Without contract:

Astro customers are entitled to a one (1) year manufacturer warranty and (6) months Installation warranty. During this period, after-sales service is free of charge. However, when your Installation warranty period is over, all after-sales service is subject to a minimal service charge starting fromRM65 inclusive of 8% service tax.

Yes, you can manage all of your Astro Fibre subscriptions with the Astro Fibre App. However, you would need to create a different Astro ID for each Astro Fibre account.

STEP 1
On your Astro remote, press the HOME button and the home menu will be displayed on top of your screen.


STEP 2
Navigate to Settings.


STEP 3
Navigate to STB Diagnostics and press "OK".


STEP 4
Select General Diagnostics and press "OK".


STEP 5
General Diagnostics results will be displayed on the screen.
Scroll until observed the SW Download Status.

Currently, you may only add a maximum of five family members to the Astro Fibre App. However, kindly note that we are working on allowing users to add more family members in the future.

Your account number will be used to identify/verify you for all After Sales-Services. You may also use your mobile number/ Astro smart card number/ NRIC number or Astro Box number.

No, you are still able to subscribe to iQIYI on your current Astro pack.

When playing content from the Video On Demand library, a 15-second or 30-second video advertisement(s) will be shown before the On Demand programme starts. All advertisements will display a countdown to indicate the time remaining on the advertisement(s) and will not be skippable.

To find out more information on Astro GO advertising, please click here.

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

2.Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user

Password: user

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi to configure the WiFi parameters.

6. You may change the Wi-Fi Name and the Wi-Fi Password as per your preferences, then click "Apply".

7. Your Wi-Fi Name and password has been changed. Kindly ensure to reconnect your WiFi according your new WiFi name and password.

Yes, however we do advise keeping your subscription while your TV is being fixed to avoid having to download the app again.

Astro Quick Pay is a convenient method to check your Bill Summary, Account Status and pay Astro bills at your convenience with immediate payment posting, right from home. Visit Astro Quick Pay to pay your bill now.

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.
2. Ensure the fiber cable from your wall socket and modem is securely connected.

Notes: You might be connected to LAN 1 if backbone is Maxis

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option  2/ Option 3/ Option 5/ Option 6

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.    

2. Ensure the fiber cable from your wall socket and modem is securely connected.

3. Ensure both cables on the Modem (LAN Port 2) and Router (WAN Port - Red port) are properly connected.

Notes: You might be connected to LAN 1  if backbone is Maxis
 

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. Please make sure both cables on Router (Any Yellow port) and Astro Decoder (Network Port behind decoder) are properly inserted.

5. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

6. If the issue persists, submit your feedback form and attach your modem light indicator picture/ video for further assistance.
 

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

We are working with the Sony team to ensure you will be able to enjoy these 4K UHD channels soon. We will keep you posted once these channels are available to you!

Some of our payment partners require payees to scan the barcode on the statement to make payment. Always bring your Astro bill statement when making payment over the counter.

If you would like more information or to provide feedback on Astro Rewards, kindly reach out to us at 03 9543 3838 or visit one of our Astro service centres.

Astro is no longer updating the software in non-Ultra/Ulti Boxes as they have reached their end-of-life cycle. Therefore, non-Ultra/Ulti Boxes will maintain their current classification systems. Nonetheless, you may refer to content.astro.com.my for all the updated age ratings. Please refer to the table below to see the difference in classification systems between our platforms:

STEP 1

‍

Try to change channels on your Astro  remote.

INDICATOR: LED blinking 3 times / NO LED blink

SOLUTION: Replace new battery

Proceed to Step 2.

‍

INDICATOR: LED blinking 1 time

Confirm it's not your Astro remote faulty, let's proceed to Step 3.

‍

STEP 2

If issue remain after the battery replacement, this might be due to a faulty Astro remote.

Try changing the channel manually directly from the box front panel (If any).

If it's working, you might need to  replace your Astro remote.

You may walk-in to our nearest Customer Service Center for the replacement.

STEP 3

You need to refresh the box setting by initiate manually from box front panel.    

Refer to Refresh Box setting Guide steps here.

Step 1:
Type ASTRO<space>BAL<space>10-Digit Astro Account No. 
Example: ASTRO BAL 08XXXXXXXX

*Standard telco charges and Terms and Conditions apply

Step 2:
Send SMS to 66688

STEP 1
Switch off the power of your box and make sure that the adapter’s power light is off.


STEP 2
Unplug the HDMI cable from your TV and plug it back in securely to other available HDMI port.


STEP 3
Switch on the power for your box and make  sure that the adapter’s power light is on.
Please wait for 5 minutes.


STEP 4
Turn on your box. Do select the correct TV input.
You should no longer be experiencing this problem. 
​

Broadband Deal bundle are recommended packages offered to customers with higher rebate as compared to Broadband Non-Deal bundle.

Customers with HD boxes can subscribe to the All-New Astro Pack without a box upgrade except if the customer request to move to OTT bundled pack which is mandatory to upgrade to Ulti or Ultra. 

Note: OTT is referring to either Netflix, D+H or both.

STEP 1    

On your remote, press the ... button and the Channel Guide page will be displayed on your screen.

STEP 2    

Select the channel you would like to remove as favourite and press "OK".

STEP 3  

Select "Remove from Favourite" and press "OK".

STEP 4    

You are successfully removed the channel from favourite list when this screen appears.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to Digital Audio and press "OK".

STEP 4    

Choose your preferred selection and press “OK”.

STEP 5    

Select Yes, continue and press "OK" to confirm on the changes.        

Otherwise, select No, go back to cancel.

Yes, the current service tax law does not exempt services provided to customers residing in Labuan, Langkawi, and Tioman.

Of course not! It is a value-added service introduced for your convenience.

Yes, if a device is faulty due to the customer's negligence, they will be subjected to a penalty fee for each device:

• WiFi router: RM200

• Fibre modem: RM500

• Mesh WiFi: RM200/unit

Unfortunately, you will no longer be able to access Disney+ Hotstar via Astro if you cancel your Astro subscription with Disney+ Hotstar entitlement. 

STEP 1  

On your remote, press the HOME button.

STEP 2

Navigate to SETTINGS icon and press "OK".

‍

STEP 3  

Navigate to Manage Satellite Frequency and press “OK”.

STEP 4

Choose Test Satellite Frequency and press “OK”.

STEP 5  

Choose "Confirm" to continue Test Satellite Frequency and press “OK”.

‍

STEP 6  

Satellite Frequency Test progress screen will be displayed.

‍

STEP 7  

The test result will be displayed once completed.

Kindly note that affected customers will be adequately informed 30 days prior to the implementation via SMS which are sent out in phases (Starting 1 July), with scheduled announcements across WhatsApp, My Astro app, and Astro website.