You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

Please refer to these FAQs and Terms and Conditions for more information.

For more support and options for your subscription, please WhatsApp us at 03 9543 3838 and type DH Help. Alternatively, you may visit astro.com.my/Disney for more information.

Astro introduces Liga Malaysia for all Astro customers to watch the Malaysian Football League’s Liga Malaysia competitions LIVE, comprising Perlawanan Sumbangsih (Piala Sultan Haji Ahmad Shah), Liga Super, Piala FA and Piala Malaysia live in HD on Astro Arena (CH801), Arena Bola channels (CH803 and CH804) and stream on Astro GO until further notice.

No, there is no penalty or switching fee if you decide to cancel your Multiroom (Smart TV) subscription.

You can proceed with below BTS if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to Diagnostics and press “OK”.

STEP 5

Refer to the signal strength on your screen.

If it is 65 or higher, please take the screenshot and submit your feedback form.

If it is below 65, please go to Step 6.

STEP 6

Switch off the power for your box and  make sure that the adapter’s power light is off.

STEP 7

Unscrew the satellite cable from the box  and pull it out.

STEP 8

Plug the satellite cable back into the  box and screw it back securely.

STEP 9

Switch on the power for your box and make sure that the adapter’s power light is on. Please wait for 5 minutes.

STEP 10

Turn on your box. You should no longer be experiencing this issue.

If issue persist, please submit the issue on our Feedback Form with error details and attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized  Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

If you add on the Mesh WiFi during your initial order of Astro Fibre, there is no additional installation fee. If you order the Mesh WiFi as an add-on at a later time, you will have to pay RM49 per installer visit. However, if you choose to have the Mesh WiFi delivered via courier in order to self-install your Mesh WiFi, there will be no installation or delivery fee charged.

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3    

Navigate to HDMI Audio and press "OK".

STEP 4  

Navigate to your preferred selection and press “OK”.

Your existing offers with us will not be affected and will continue until the agreed upon date. 

SST of 6% and 8% will be applied accordingly to your bundle services:

1. 8% SST to Astro TV Pack
2. 6% SST to Astro Fibre

Yes, provided that your Plug & Play Box has not been activated and no later than 7 days upon receiving both the Plug & Play Box and Astro SIM card. In the event that you have activated your Plug & Play Box and wish to cancel, a contract penalty fee will apply.

We will reach out to you for a suitable time to pick up the Plug & Play Box and Astro SIM card.

STEP 1
Check the Audio settings on your box and set to Auto.
Refer guide to change Digital Audio Settings.

STEP 2
If issue persist, check if there is any 3rd party device (sound system/hdmi splitter) connected between box and TV.

STEP 3
If using 3rd party devices, bypass/remove 3rd party device and make sure HDMI cable connected directly from box to TV.

STEP 4
If issue persist, connect to Live Agent via WhatsApp for help.

Kindly note that affected customers will be adequately informed 30 days prior to the implementation via SMS which are sent out in phases (Starting 1 July), with scheduled announcements across WhatsApp, My Astro app, and Astro website.

Yes, customers may need to provide additional documents such as bank-in slips or payment receipts. Any incomplete document, customer will be notified by Astro after validation is made.

We wish to advise you to make your payment before the following month's bill is generated in order to avoid interruption in your viewing experience. Please note that to reconnect your subscription, there will be a charge of up to RM20 (excl. gov tax) upon reconnection, except for Commercial & Hotel customers.

Find out more about the reconnection fee here.

STEP 1    

On your remote, press the Home button and the menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3    

Navigate to Restore and press "OK".

STEP 4    

Navigate to Restore Factory Settings and press "OK".

STEP 5

Enter your PIN to access this setting. (Default PIN is 0000).

STEP 6    

Navigate to Restore and  press "OK" to  confirm your selection.    

Otherwise, navigate to Cancel, go back to remain the settings.

STEP 7    

Please wait while the box restoring defaults and will reboot once complete.

STEP 8    

Your box will automatically restart and display this screen.

Click here to follow New Installation Settings guide for Satellite

Click here to follow New Installation Settings guide for Plug and Play

The Liga Malaysia will be available for all Astro customers starting 3 May 2024 as part of your Astro subscription at no additional cost until further notice.
 

Photograph or scan your payment receipt, and send it to one of our contact platforms found here.

You require at least two devices to form a Mesh WiFi network which are Astro Fibre WiFi router and a Mesh WiFi unit.

The Mesh unit will link to the WiFi router to form the Mesh WiFi network. You may connect up to 5 Mesh WiFi units for optimal WiFi coverage in your home.

Having trouble with  your phone line ?

You may proceed to contact dedicated service provider directly - 1 800 8211 23

You will require HD-PVR service in order to subscribe for a PVR. This service is included in all Starter Pack, Value Pack, Super Pack Lite, Super Pack and Super Pack Plus subscriptions.

Redemption should be done by the account holder. However, if the account holder is unavailable, immediate family members can make the redemption provided that the account holder has given them the permission to redeem using his account credentials.

No, please use a Malaysian mobile number registered with a local network service to register and activate access for Disney+ Hotstar with your Astro subscription. 

Please ensure that you have subscribed to PVR recording service.

If you're subscribed to PVR recording service, follow below steps.

‍

Let's  check your hard disk connectivity.

STEP 1

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4

From the General tab, take a look at the HDD Status.

If status is "Connected", press red button to reboot you decoder.

Wait until the box is on, then try to record any program.

‍

If issue persist, please submit the issue on our Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

If status is "Disconnected", please submit your Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

The New Astro First serves as the one-stop, ultimate home cinema offering the biggest and latest local and international blockbuster films where you can:-

• Enjoy value for money viewing for local and international movies from only RM15* per movie or RM17* for UHD movies (*excluding tax).
• Stream each rented movie for as many times as you like within 48 hours* (*unless stated otherwise) anytime, anywhere via On Demand on your Astro Box or Astro GO.
• Watch local/regional movies or international movies from Hollywood studios as recent as 2 weeks or 3 months respectively from Malaysia's cinematic release, in addition to exclusive titles only available on Astro First.

Want to return or recycle your satellite TV devices? It's simple and free!

Here's what you can do with your unused satellite TV devices:

If you have an Ultra or Ulti Box, you may:

1. Return your device to us via Arranged Pick-up:

Step 1: Please call Astro's Contact Centre at 03-9543 3838 to schedule an arranged pick-up by one of our Astro agents.

Step 2: Just sit back and relax! Our courier partner, Citylink will come to your doorstep, dismantle the satellite dish for you and retrieve the devices.

 2. Return your device to us via Dropoff:

Step 1: Please gather your device(s) and click here to find a Customer Service Centre (CSC) or Astro Authorised Retailer (AAR) near you.

Step 2: Don't worry, it's free! Simply walk in during opening hours and hand over the device(s) to one of our Astro agents.

Note: An installer's visit is required to dismantle your satellite dish. However, if you have a Box or other satellite TV devices at home that do not require dismantling, you may walk into any of our authorised dealers and hand them over to the agent.

If your Satellite TV device is NOT an Ultra or Ulti Box, you may:

1)   Recycle your device:

For all Ultra or Ulti Boxes, please return them to Astro via drop-off at a CSC or AAR near you or schedule a pick-up appointment via 03-9543 3838.

For other older Boxes or Satellite TV devices, you are required to discard them only at registered collection centres for proper handling and management of e-waste in an environmentally sound manner. Click here to find a registered collection centre near you.

Note: Upon termination of your Astro service, all Ultra and Ulti Box customers are required to return their devices to Astro. Failure to do so within 14 days of termination may incur a fee of RM100 (not inclusive of Govt. Tax). For customers on all other boxes, please discard your box only at registered collection centres to ensure we all play our part in protecting the environment.

Frequently Asked Questions

Arranged Pick-Ups

1) I missed the pickup appointment; what do I do now?

Our agent will make two attempts to retrieve the device(s) and dismantle your satellite dish within a period of 14 days, failing which the penalty of RM100 (not inclusive of Govt. tax) would be imposed.

2) Can I reschedule my pickup date?

Yes! Please call Astro's Contact Centre at 03-9543 3838 to reschedule your pickup date.

3) My old devices do not require dismantling; do I have to pack them before handing them over to the delivery agent?

Please pack your device(s) in their original box/packaging if possible. If this option is not available to you, just hand the device(s) over to the delivery agent without any packaging. You will not be charged any fees if the original packaging has been damaged/lost.

4) Do I have to print anything or fill in any forms before handing my device(s) over to the Astro agent?

No, you do not have to prepare any documents before handing your device(s) over to the Astro agent. All you have to do is get your device(s)ready before the Astro agent arrives to ensure a smooth handover process.

5) I have an old/unused satellite dish at my home and I am not an Astro customer; can I still schedule an installer visit to dismantle and return it?  

Yes! Not to worry, you can still schedule an installer visit to dismantle the satellite dish from your home.

Drop-offs

1) Do I have to pack my device(s) before handing it over to the Astro agent?

Please pack your device(s) in their original box/packaging if possible. If this option is not available to you, just hand the device(s) over to the Astro agent without any packaging. You will not be charged any fees if the original packaging has been damaged/lost.

2) There are no Customer Service Centre (CSCs) or Astro Authorised Retailers (AARs) near me; what do I do now?

Please opt for courier pick-up if there are no CSCs or AARs near you. Call 03-9543 3838 now to schedule a pick-up appointment by one of our courier partners if you are holding an Ultra or Ulti Box For non-Ultra or Ulti boxes, you may recycle your box at a registered collection center. Click here to find a registered collection center near you.

3) Do I have to print anything or fill in any forms before handing my device(s) over to the Astro agent?

No, you do not have to prepare any documents before handing your device(s) over to the Astro agent. All you have to do is hand the device(s)over to the agent and you're done! You will also receive an acknowledgment slip after successful handover.

4) I found my Box and Smart card, however, the cable(s) that came with it is lost; will there be any penalty fees?

No, please return your old Plug & Play Boxes and Smartcard. There will be no penalty fees if the cable is damaged or lost.

Recycle via Registered Collection Centres

For all recycling-related questions, please click here.

Still Need a Hand?

Not to worry, we are only a phone call or a message away! Call or WhatsApp our Customer Contact Centre at 03-9543 3838 and an Astro agent will be available to assist you immediately.

STEP 1    

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Take a look at the Smart Card Status.

Want to return your Ultra or Ulti Plug & Play Box? It's simple and free!

Here's what you can do with your unused Ultra/Ulti Plug & Play Box:

1. Return your device to us via Arranged Pick-up:

Step 1: Please call Astro's Contact Centre at 03-9543 3838 to schedule an arranged pick-up by one of our courier partners.

Step 2: Just sit back and relax! A courier agent will come to your doorstep to retrieve the devices.

Your account may be under suspension. To resolve this issue, proceed to submit report via WhatsApp or Feedback Form.

While this technology has its benefits, different devices at home have different reaction and response to changes in signal strength and quality, and it's almost impossible to predict if they will make good band choices due to the interaction between the devices and the Wifi router. Some smart home devices also recommend that band steering is not used due to various reasons such as needing a constant consistent connection, ability to only connect to a particular band, registration of the respective MAC address, etc..

Example:

As single SSID is used, the device may remain on a weak 5GHz network  instead of switching over to stronger 2.4GHz network.

No, Astro GO is a free app for Astro customers. The content available on Astro GO will depend on the subscription pack that you are subscribed to.

If you do not have an Astro subscription, please click here to find out packages available.

No, eligible customers will not be charged for this speed upgrade. Your speed plan will be upgraded automatically for 24 months, depending on your subscription. After the FREE speed upgrade period, your Astro Fibre plan will return to its regular speed.
 

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Master PIN and press “OK”.

STEP 4

Please enter your PIN (Default PIN is 0000).

STEP 5

Please enter your new PIN.

STEP 6‍

Please re-enter your new PIN to confirm.

STEP 7

Your PIN successfully changed when this  screen appears.

Step 1:  Launch the app on your Smart TV.

Step 2: You will be able to see a welcome screen with a QR code and URL.

Step 3: Scan the QR code or go to astro.com.my/tvapp on your mobile and enter your unique code (e.g. FSJV-SMBS) displayed on the TV screen

Step 4: At the login page, you will need to log in with your Astro ID (registered email or mobile number) and password.

(If you do not have an Astro ID, click on "Create now" 

to sign up and link to your Astro account – check the following on the steps) 

Step 5: Once you have successfully logged in on your mobile, the Astro app will launch on your Smart TV screen. You can continue to browse and watch your favourite shows on the Smart TV.

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

2.Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user

Password: user

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi to configure the WiFi parameters.

6. You may change the Wi-Fi Name and the Wi-Fi Password as per your preferences, then click "Apply".

7. Your Wi-Fi Name and password has been changed. Kindly ensure to reconnect your WiFi according your new WiFi name and password.

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3  

Navigate to Satellite Settings and press "OK".

STEP 4  

Select Diagnostics and press "OK".

STEP 5    

Signal reading on Tuner 1 will be displayed. Navigate to right arrow for next step.

STEP 6  

Signal reading on Tuner 2 will be displayed. Navigate to "Done" and press "OK" to complete the diagnostics.

Currently, you may only add a maximum of five family members to the Astro Fibre App. However, kindly note that we are working on allowing users to add more family members in the future.

BYOND / PVR / Ultra Box

To dismantle ONLY - FOC
‍
To reinstall ONLY – RM65
‍
To dismantle and reinstall - RM65

‍

Broadband / IPTV

Relocation within 6 months of contract start will be charged a RM500.00 relocation fee, and the contract will be renewed to a new 24-month contract.

Relocation after 6 months of contract start will have their contract renewed to a new 24-month contract.

‍

Note For IPTV Customers: 

1. Upon relocation request, all exiting IPTV customers will be converted to our Astro & Broadband service. Customers can choose to have standard Astro service with satellite dish, or unicast Plug & Play without satellite dish.

2. If customers choose to have satellite dish, an additional RM150.00 will be charged for satellite installation. If customers choose to have unicast Plug & Play service, no satellite dish is required, hence no extra charge will be incurred.

‍

‍

*Please note that additional charges may apply if the reinstallation process requires extra cables/fixings.