You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)
 

Username: admin
Password: admin (or time123)

 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

• On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab

• Please ensure Wireless RF Mode is Enabled.

• Click the drop-down arrow for Channel, then select your desired channel.
• Choose between 1 until 11 (Suggested 1,6,11).

• Click Submit. Router will auto reboot and connection re-establish after few minutes.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the Smartcard at the front or right side and gently pull it out make sure that the adapter's power light is off.

STEP 3

Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be  experiencing this problem.

If issue persist, please submit your feedback form with error details and attach a picture of your sim card number for assistance.

From 8 October 2021 onwards, Astro will be ceasing the daily passes (e.g. 3, 5, 7 & 30 days passes). Please subscribe to the relevant packs to continue enjoying your favourite content. Stay tuned for more exciting offers. Thank you.

By default, all Astro Fibre customers will receive a Private IPv4 or IPv6 address. However, customers who would like to subscribe to a fixed IP service can do so by contacting our Customer Service Centre at 03-9543 3838 for Astro Fibre’s Fixed IP service for only RM5/month.

Not all shows/channels will be available on the Plug & Play Box as this depends on contractual rights with specific guidelines on the entitlement of these shows/channels and what you have as a part of your subscription.

• Customers subscribing to Plug & Play Box with or without Astro Broadband will not have access to 1 (one) Channel - NHK World

Please be assured that we are continuously working hard to make more content available on the Plug & Play Box.

If you prefer to have all these channels, we recommend that you choose the Satellite dish option for the Ultra or Ulti Box.

Unavailable channels are as below:

No, if you already have an Ulti box you will not be required to swap the box to enjoy the new packs. However, if you would like to access 4K UHD content, you may upgrade to Ultra Box. Installation and activation fees will be chargeable depending on your package selection.

Only new and existing Astro Fibre customers with the latest RG21 router can use the Astro Fibre app.

Astro is no longer updating the software in non-Ultra/Ulti Boxes as they have reached their end-of-life cycle. Therefore, non-Ultra/Ulti Boxes will maintain their current classification systems. Nonetheless, you may refer to content.astro.com.my for all the updated age ratings. Please refer to the table below to see the difference in classification systems between our platforms:

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please ensure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Intermittent internet connection using Wi-Fi

1. Router Positioning
   Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
   
    i) High vs. Low
   Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   
   ii) Concrete & Metals
   Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   
   iii) Distance to Router
   The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
   
   Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.
   
    

2. Wireless Interference & Noise
   You've probably never noticed but there are wireless signals all around you wherever you go and they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.
   
   Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:
   i) Microwaves
   ii) Bluetooth Devices
   iii) Cordless Phone
    

3.  Surrounding Wi-Fi signals
   A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel  overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many  routers within close proximity. Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

4. Usage
   More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

You can recover your Netflix login here or at astro.com.my/Netflix

Step 1: Head to astro.com.my/Netflix

Step 2: At the FAQ section look for "How to recover my Netflix login email and password

Yes, any active Astro subscriber with a minimum primary subscription fee of RM100 can subscribe to a Multiroom (Astro Box) at a price of RM49.99 monthly with the box setup (subscription price is subject to Govt Tax).

Customers with a Movies subscription via Movies, Premium 1, Premium 3 and Platinum packs will be able to access Disney+ Hotstar on the Ultra box.

Alternatively, customers can add on the 3-month Disney+ Hotstar pass for RM54.90. Subscribe to Disney+ Hotstar via astro.com.my/Disney.

For more support and options for your subscription, please WhatsApp us at 03 9543 3838 and type DH Help. Alternatively, you may visit astro.com.my/Disney for more information.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

From General Tab, look at the Smart Card No for the smartcard number.

STEP 5    

Take look at the Set Top Box Serial Number for the box serial number.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/ laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/ laptop].
2. You may open any web browser such as  Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)

Username: admin
Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the  configuration.

i. On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab.

ii. Please ensure Wireless RF Mode is Enabled.

iii. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

iv. Click Submit. Router will auto reboot and connection re-establish after few minutes.

You must subscribe to an Astro subscription (NJOI customers are not eligible) in order to get the Ulti Box. 

‍

The eligibility criteria for the Ulti Box are as follows:

New Customers

All new Astro customers with a monthly subscription fee of below RM100 will be entitled to select the Ulti Box upon signing up for Astro’s packages. 

‍

Existing Customers (Box Upgrade for Primary or Multiroom)

Existing customers are required to have an internet connection at home with a recommended internet speed of 10Mbps and above in order to upgrade your existing box to Ulti Box. 

Note: 

·      Existing Ultra Box customers are not eligible for a swap to the Ulti Box.

·      If your existing box is a PVR, you will lose access to all the recordings stored in the PVR

‍

Multiroom (New subscription)

Customers subscribing for an additional multiroom subscription are entitled to select the Ulti Box as part of the subscription.

For Residential Astro Pay TV customers: You may change your contract from e.g., 12-month to 24-month without incurring a switching fee or cancellation fee. However, if you change your contract from e.g., 24-month to 12-month, will be charged a cancellation fee accordingly if still within minimum term (contract) period. No switching fee applicable.

For customers with the Ultra or Ulti Box, you are required to return only the Astro box along with the Smart/SIM Card. There  is no requirement to return the remote control, power cables or satellite  dish/outdoor unit (ODU).

For customers on other Boxes, you are required to discard them (and their accompanying devices such as the Smart/SIM Card) only at registered collection centers for proper handling and management of e-waste in an environmentally sound manner. Click here to find a registered collection center near you.

Please be sure to take your decoder, satellite dish, smartcard, remote control and all other fixtures after dismantling is done by the technician.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

Please contact us through one of our platforms found here or Self-serve by logging in to Astro Self-Service Portal within 3-7 days before moving out and we will sort everything out for you!

STEP 1
On your Astro remote, press the HOME button and the home menu will be displayed on top of your screen.


STEP 2
Navigate to Settings.


STEP 3
Navigate to STB Diagnostics and press "OK".


STEP 4
Select General Diagnostics and press "OK".


STEP 5
General Diagnostics results will be displayed on the screen.
Scroll until observed the SW Download Status.

Yes, if a device is faulty due to customer's negligence, it is subject to a penalty fee for each device:

• WiFi router: RM200

• Fibre modem: RM500

• Mesh WiFi: RM200/unit

Please ensure that you have subscribed to PVR recording service.

If you're subscribed to PVR recording service, follow below steps.

‍

Let's  check your hard disk connectivity.

STEP 1

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4

From the General tab, take a look at the HDD Status.

If status is "Connected", press red button to reboot you decoder.

Wait until the box is on, then try to record any program.

‍

If issue persist, please submit the issue on our Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

If status is "Disconnected", please submit your Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

Step 1: Download the My Astro app from either the App Store, Google Play or HUAWEI AppGallery.

Step 2: Sign in with your Astro ID.

Step 3: Select "Rewards" on the home screen to get started.

Watch this tutorial to learn how to create your Astro ID.

Visit our page to find out about our new packs.

Astro Quick Pay is a convenient method to check your Bill Summary, Account Status and pay Astro bills at your convenience with immediate payment posting, right from home. Visit Astro Quick Pay to pay your bill now.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.
 

1. Try loading the site on a different device.
   • Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.
   • If the website doesn't load on another device, the problem is either with the network
2. Restart your computer.
   • Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.
3. Try loading the site in a different browser.
   • There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.
4. Temporarily disable your antivirus program.
   • Your antivirus software may be interfering with your ability to load certain websites.
   • Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.
5. Reset  your modem and router.
   • Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.
6. Check your computer's date and time settings.
   • If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.
   • Check your computer or mobile device's clock to make sure that it is set to the correct time and date.

i. List of websites effected.
ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.  
iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.
iv. Run the Ping Test -  Please click here for Ping Test guideline.

Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.    
A Traceroute Test traces the route of packets to destination host from our  server.

Astro GO is a free streaming companion app for all Astro customers to enjoy their favourite shows and channels on their smartphones, tablets, and computers - anytime, anywhere in Malaysia. Astro customers with an active Pay-TV subscription can link their accounts to watch corresponding on demand and TV channels available on Astro GO as part of their subscription.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to TV Settings and press “OK”.

STEP 4

Navigate to your preferred selection and press “OK”.

STEP 5

Navigate to Save and press "OK" to confirm your selection.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your Ultra Box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

If you choose to self-install the Plug& Play Box, then no installation fee will be charged. However, there will be an activation fee (please refer to the table below)

If you choose to have an installer to install the Plug & Play Box, then an installation fee will also apply.

You will receive an email within 45 minutes of payment made to let you know whether your advance payment is successful or not. If your payment has failed, you may call Astro's Contact Centre at 03-9543 3838 or wait for an Astro representative to be in contact with you within 2 working days to assist you with your order.

When playing content from the Video On Demand library, a 15-second or 30-second video advertisement(s) will be shown before the On Demand programme starts. All advertisements will display a countdown to indicate the time remaining on the advertisement(s) and will not be skippable.

To find out more information on Astro GO advertising, please click here.

You would need your 10-digit account number and your email address.

1. Unifi netis brand

The following shows an Interface based on Unifi router

1. Launch Web Browser and enter the default's gateway's IP address (192.168.1.1) in the address bar.

1. Enter Username and Password.
   1. Username = tmadmin
   2. Password = Adm@xxxx (xxxx refers to last four digits of MAC address)

1. Choose WLAN -> wlan0 (2.4GHz) Basic Setting. Note down on SSID.

1. Choose WLAN -> wlan1 (5GHz). Compare SSID with previous SSID.

1. If SSID for wlan0 (2.4GHz) and wlan1 (5GHz) are the same. Change wlan1 (5GHz) SSID by adding number 5(i.e. ifuni_5G) to differentiate from 2.4 GHz. Click Apply Changes.

Note: Connection to Wi-Fi may be temporarily loss while the changes is updated.

STEP 1

Switch OFF the power of your Ultra / Ulti box and make sure that the adapter's power light is off.
 

STEP 2

Switch ON the power of your Ultra / Ulti  box and make sure that the adapter's power light is on.
 

STEP 3

On your remote control, press the Home or Standby button repeatedly until the Startup Options appear on TV.



STEP 4
Press "987" to proceed.
Advanced Startup Options will be displayed.



STEP 5
Press "1" to initiate a reset setting.



STEP 6
Press "OK" to continue.



STEP 7
After the factory setting is restored, TV will turn blank.
Please wait until the box completes initiate setup.



STEP 8
Once completed, the following screen will appear on your TV.
Refer to Installation Setup guide to complete the setup.

Click here to follow New Installation Settings guide for Satellite
Click here to follow New Installation Settings guide for Plug and Play

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Video Resolution and press “OK”.

STEP 4

Navigate to your preferred selection and press “OK”.

Recommended to select Auto.

STEP 5

Navigate to Save and press "OK" to confirm your selection if able to read the text properly.

Otherwise, navigate to Cancel to revert to previous settings.

The service tax rate for Astro Pay TV will be increased from 6% to 8%. The service tax for Astro Fibre, which falls under the category of telecommunication service, will remain at 6%.