STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be experiencing this problem.    

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

Please note that only one Disney+ Hotstar access is bundled to each TV Pack subscription which allows two concurrent streams on Disney+ Hotstar. 

Refund  can be made when there be a termination of account, over payments and in  cases where payment was wrongly made to another Astro account.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the blue port in Cisco Router and direct to computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

‍

‍

4. Type the Username and Password as below. Then click "OK". (These are the defaults, if you have done previous configuration on your router the password may be different).

Username: admin

Password: admin (or time123)

5. Click "OK" when a Warning prompt that says,” Using this advanced utility to change your router settings could disable your network” appears. Below display will appears.

6. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

7. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

8. Click Wireless Security to view the security settings of your wireless network. Take note of the Security Mode and the Passphrase.

For the example below, the Security Mode used is WPA2/WPA Mixed Mode.

The Wireless name is called Network Name (SSID) and the Passphrase is your wireless password.

‍

9. Now that you have the Wireless name and Password, you are ready to connect your wireless computers and devices to the network.

10. You may change the Network Name (SSID) and the Passphrase to follow your preferences and please ensure save the changes made. Please reconnect to the new wireless name with the new password once completed.

‍

Step 1: Open your My Astro app

Step 2: Select "Astro Rewards"

Step 3: Scroll through your rewards to see what you're entitled to

Step 4: Select the rewards that take your fancy and follow the instructions stated on how to redeem them (redemption instructions may vary based on reward)

1. Power reset (on & off) your TV, Astro Decoder, Modem and Router.

2. Ensure standard physical connection (No 3rd party devices connected to decoder and modem).

3. Please ensure at all-time your router is 0.5 meter away from your Astro Decoder to avoid signal interferences.

4. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [connect the LAN (cable) at any LAN port at router and direct to computer/laptop].

5. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

6. On the address bar, please go to http://www.speedtest.net/ and below page will appear.

7. Click "Change Server" to edit the settings preferred by Internet Service Provider (ISP).

8. Edit the server settings by search and select the required server required by ISP.

    For Maxis provider - Select Subang Jaya - Maxis server.

    For TIME provider -  Select Shah Alam - TIME dotcom Bhd server.      

    For Allo provider -  Select Cyberjaya - Global Forway Sdn Bhd server.

9.Click "GO", and the test will  begin.

The test is completed once both download and upload speeds are displayed.

Sample of the Speedtest result is shown below.

**Please  ensure the snapshot includes a time stamp and network used either LAN cable  or wireless (as per picture above)

10. Kindly screenshot or take a picture of the result, name it as "LAN Speedtest".

11. Repeat the test once again using Wi-Fi connection (Please unplug your LAN cable and connect via wireless connection using your SSID).

12. Screenshot or take a picture of the  result, name it as "WiFi Speedtest".

For information about the Disney+ Hotstar app functions and specifications, please visit help.hotstar.com or email disneyplus.my@hotstar.com. 

Astro GO is a companion app that is complimentary for all Astro subscribers and allows up to 2 users to stream at the same time. 200 hours of cloud recording* come complimentary with your Pay TV subscription. 

Astro GO+ is an add-on service that enables up to 4 users to stream Astro GO and/or Multiroom Smart TV** at the same time. The amount of cloud recording storage will also be increased to 1500 hours. 

 *Cloud recording hours are shared across your Astro Box, Astro GO and Multiroom Smart TV 

** Provided that you have a Multiroom Smart TV subscription

We want to ensure that only the authorised account owner can have access to their Astro account. This activity ensures that only you can log in and access all the details tied to your Astro account.

Yes, Mesh WiFi add-on is available for both Astro Fibre Bundle and Astro Fibre subscription.

No, you are not allowed to change your due date or maintain your old due date. Your current due date is as per Astro Policy. Therefore, to ensure that you continue to enjoy uninterrupted services, we advise you to observe this change in due date from Day 30 to Day 25 and proceed with the necessary payment.

Having trouble with  your phone line ?

You may proceed to contact below dedicated service provider directly

1 800 1818 18

We try to make as many movies and TV shows available for download. However, for some titles, while we may have the rights to offer them via streaming, we may not be able to offer them for download.

This initiative is part of Astro’s “GO GREEN” journey, which was implemented to promote paperless billing and to play our part in protecting the environment. The objective of the Paper Bill Charge is to encourage our customers to opt for e-Billing as their preferred Bill Delivery Method, which is also a more convenient and efficient way to access and manage their bills. Hence, a fixed RM10.00 monthly charge will be applied to all existing and new Astro customers who opt for Paper Bills as their preferred bill delivery method.

Please follow the steps below:

Step1: Fill in Merge/Split Equipment Form (Part A & Part B)

Step2: A full payment to be made on any outstanding balance for all related accounts (if any).

Step3: Submit all documents via feedback form or walk in to nearest Astro Customer Service Centre (CSC).

Step4: Customer will expect a call from our validation team (Note: Turnaround time for merge/ split of account is 3-5 working days upon receiving all complete documentation).

Note:

1. There might be a loss of transmission during the processing of transfer equipment ownership, split or merge of equipment.

There are no extra charges as it is a value-added service introduced provided for your convenience.

If you have NOT made any changes to your Astro pack on or after 9th November 2021, you can enjoy up to four (4) concurrent streams on Astro GO anywhere, anytime. However, if you have Astro GO+ as part of your subscription, you will be upgraded to four (4) concurrent streams.

1. Unifi netis brand

The following shows an Interface based on Unifi router

1. Launch Web Browser and enter the default's gateway's IP address (192.168.1.1) in the address bar.

1. Enter Username and Password.
   1. Username = tmadmin
   2. Password = Adm@xxxx (xxxx refers to last four digits of MAC address)

1. Choose WLAN -> wlan0 (2.4GHz) Basic Setting. Note down on SSID.

1. Choose WLAN -> wlan1 (5GHz). Compare SSID with previous SSID.

1. If SSID for wlan0 (2.4GHz) and wlan1 (5GHz) are the same. Change wlan1 (5GHz) SSID by adding number 5(i.e. ifuni_5G) to differentiate from 2.4 GHz. Click Apply Changes.

Note: Connection to Wi-Fi may be temporarily loss while the changes is updated.

For more information about the Astro Fibre App, you may click here for a detailed user guide.

Starting 12 December 2023, users have to use their registered email address, mobile number or a social account (Facebook, Google or Apple) to log into any of Astro's digital platforms, including My Astro, Astro GO and Astro's official website. Usernames as an Astro ID is no longer available. This change was made to ensure details linked to your Astro account are always updated and to improve the overall user experience on our platforms.

Yes, you can manage all of your Astro Fibre subscriptions with the Astro Fibre App. However, you would need to create a different Astro ID for each Astro Fibre account.

No, you will not be charged 8% Service Tax for paper billing option.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to TV Settings and press “OK”.

STEP 4

Navigate to your preferred selection and press “OK”.

STEP 5

Navigate to Save and press "OK" to confirm your selection.

This error indicates that you have reached the maximum number of simultaneous video streams across devices for one (1) account. To stop seeing this error, please stop streaming on one of your other devices.

• If you have recently purchased your Astro pack or made any changes to your pack on or after 9th November you can stream on two (2) concurrent screens

• If you have not made any changes you can stream on four (4) concurrent screens.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.
 

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

No, you are still able to access HBO Go on your current Movies pack.

STEP 1

‍

Try to change channels on your Astro  remote.

INDICATOR: LED blinking 3 times / NO LED blink

SOLUTION: Replace new battery

Proceed to Step 2.

‍

INDICATOR: LED blinking 1 time

Confirm it's not your Astro remote faulty, let's proceed to Step 3.

‍

STEP 2

If issue remain after the battery replacement, this might be due to a faulty Astro remote.

Try changing the channel manually directly from the box front panel (If any).

If it's working, you might need to  replace your Astro remote.

You may walk-in to our nearest Customer Service Center for the replacement.

STEP 3

You need to refresh the box setting by initiate manually from box front panel.    

Refer to Refresh Box setting Guide steps here.

Service Tax will not be imposed on any CSR projects accounts. Any tax payable will be borne by Astro.

Yes, you can return the Astro Box & Smart Card/SIM Card even after being charged for the box fee. After successfully returning the box, Astro will proceed to refund the box fee within 30 days from the confirmation date of the returned items to our Astro warehouse.

If your existing Netflix account is linked with your Astro subscription, your Netflix account will resume on the previous method of payment. If you linked a new Netflix account with your Astro subscription, cancelling Astro service will also cancel your Netflix account.

• Bundle Packs with Chinese Favourites: If you are currently on the Chinese Favourites selection, your selection will switch to Viu Premium at no additional cost progressively from 1 April 2024. Not to worry, you may still manually switch to other Asian Favourite selections if you wish via the My Astro app.

• Chinese Favourites Add-ons: There will not be any changes to your current subscription pricing. Furthermore, your subscription will now include additional channels on a free preview basis.

• Old Packs: There will not be any changes to your current subscription pricing. However, as we have recently made adjustments to the channel lineup in our packs, please call us at 03-7481 1000 (Monday to Friday, 9AM – 6PM exclude public holidays) to find out how you get more value from your subscription.

Yes, the current service tax law does not exempt services provided to customers residing in Labuan, Langkawi, and Tioman.

No, the courier charges are borne by Astro for the retrieval of the box and Smart Card/SIM Card.

There will be two attempts made to retrieve the box and you are required to be available at the agreed upon time.

Yes, you can. Go to the Account tab and scroll to "Subscription' section. Select "TV pack', select "Main room' or "Multiroom' and then click the "Refresh' button.

‍

1. Please connect your computer or laptop to your Astro Fibre router using WiFi or LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

2. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, type http://192.168.100.254 and below page will appear.

‍

Login using your username and password  if you have changed the router login setting. Otherwise, your default router  login is as per below.          

Username: user
Password: user

‍

4. Once you have successfully logged in, the router's web-based setup page will appear.

‍

5. At the top of the page, click WLAN to configure the WiFi parameters.

‍

6. You may change the Primary SSID (WiFI Name) and the WPA Passphrase (WiFi Password) to follow your preferences for 2.4G Wi-Fi Settings, then click "Save & Apply" for the changes to take place.

‍

7. You may make the same changes for 5G Settings by change the Primary SSID (WiFI Name) and the WPA Passphrase (WiFi Password) to follow your preferences, then click "Save & Apply" for the changes to take place.

You would have to create a new Astro ID with your email address or mobile number and link your Astro subscription. Please follow the steps in the link here

Yes, a third party is allowed to make the advance payment on your behalf. In the case of refund, the amount will be returned to the owner of the third-party account (source of payment).

You may report the incident on WhatsApp at 03-9543 3838 by typing PNP and our access our user guide or request for further help from our dedicated agents. Please have your Airway Bill tracking numbers ready for validation. If a replacement box/Astro SIM card is deemed necessary, a new Box and a new Astro SIM card will be couriered to your service address.

Please ensure that you have subscribed to the mentioned channel.
If you're subscribed to this channel, follow below steps.

STEP 1
You need to refresh the signal on your box.
Refer to Refresh signal of your box guide.

STEP 2
If issue persist after 30 minutes, proceed to submit report via WhatsApp or Feedback Form.

You may access it by pressing "200' on your Astro remote control whilst watching TV.

You may check your bills and outstanding via:

• Channel 200 from your Astro Box.
• Astro Self Self-Serve Portal or MyAstro App via this link.
• WhatsApp "Payment" to 03 9543 3838 and follow the steps provided.

Astro continuously reviews its product propositions to ensure we can provide the best customer experience for all our subscribers. We have discontinued the 50% multiroom in order to allow our Astro subscribers with a subscription fee of RM100 or more to only pay a standard RM49.99 (with box setup)  to enjoy the Multiroom experience on an Ultra or Ulti Box.

We apologise for any inconvenience.

Yes, you are eligible for selected bundle packages with rebates up to RM39/month and a free speed upgrade if you subscribe within the promotion period. Kindly note that monthly rebates are only available for Pay TV + Astro Fibre bundles but the speed upgrade is available for all packages including standalone plans.
 

Yes, if a device is faulty due to customer's negligence, it is subject to a penalty fee for each device:

• WiFi router: RM200

• Fibre modem: RM500

• Mesh WiFi: RM200/unit

Advance payment is only applicable to Astro TV pack purchases. If you subscribe to an Astro Fibre+TV bundle, only one month of your TV subscription fee (excluding tax) is required to be paid upon sign-up. The full tax amount and the first-month subscription fee for Astro Fibre will be paid on your first month's bill.

The recommended home internet speed for a smooth viewing is 10Mbps.

The Astro Fibre app is a newly introduced mobile application exclusively for Astro Fibre customers to allow them to schedule when each user can access the internet, share network access to guests in a secure manner, easy device management, amongst many other features for a better WiFi experience. For more information about this app, please visit here.