‍

1. Please connect your computer or laptop to your Astro Fibre router using WiFi or LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

2. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, type http://192.168.100.254 and below page will appear.

‍

Login using your username and password  if you have changed the router login setting. Otherwise, your default router  login is as per below.          

Username: user
Password: user

‍

4. Once you have successfully logged in, the router's web-based setup page will appear.

‍

5. At the top of the page, click WLAN to configure the WiFi parameters.

‍

6. You may change the Primary SSID (WiFI Name) and the WPA Passphrase (WiFi Password) to follow your preferences for 2.4G Wi-Fi Settings, then click "Save & Apply" for the changes to take place.

‍

7. You may make the same changes for 5G Settings by change the Primary SSID (WiFI Name) and the WPA Passphrase (WiFi Password) to follow your preferences, then click "Save & Apply" for the changes to take place.

Photograph or scan your payment receipt, and send it to one of our contact platforms found here.

Your purchased PPV daily pass will still be accessible to you for the purchased duration ie. 3, 5, 7 or 30 days respectively. However, you will no longer be able to purchase PPV daily passes from 8 Oct onward.

Tap on the "Account' tab on the navigation bar and scroll to "Billing' section. Tap on "Bill Statement' to view any bill statement up to six (6) months.

Please contact Astro Customer Call Center via 03-95433838

You will need to bring along all devices to your new place as no new devices will be issued.

Relocation will be subjected to new 24 months recontract and standard relocation fee applies for both Maxis and Allo respectively.

You can proceed with below BTS if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to Diagnostics and press “OK”.

STEP 5

Refer to the signal strength on your screen.

If it is 65 or higher, please take the screenshot and submit your feedback form.

If it is below 65, please go to Step 6.

STEP 6

Switch off the power for your box and  make sure that the adapter’s power light is off.

STEP 7

Unscrew the satellite cable from the box  and pull it out.

STEP 8

Plug the satellite cable back into the  box and screw it back securely.

STEP 9

Switch on the power for your box and make sure that the adapter’s power light is on. Please wait for 5 minutes.

STEP 10

Turn on your box. You should no longer be experiencing this issue.

If issue persist, please submit the issue on our Feedback Form with error details and attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized  Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

Please refer below for the installation and activation fees for Astro customers on the new pack.

You are attempting to play a content that is not part of your subscription. If you are not able to play a content that you are subscribed to, proceed to submit report via WhatsApp or Feedback Form.

The service tax rate for Astro Pay TV will be increased from 6% to 8%. The service tax for Astro Fibre, which falls under the category of telecommunication service, will remain at 6%.

Tap on the "Content' tab on the navigation bar. Select "Channels' and the channel of interest and you may view the scheduled programmes of the day. To switch between days, choose a channel and tap on a particular day (E.g. Mon, Tues, Wed). You may also view the showtimes of the day and up to the next six days.

Please ensure that you have subscribed to PVR recording service.

If you're subscribed to PVR recording service, follow below steps.

‍

Let's  check your hard disk connectivity.

STEP 1

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4

From the General tab, take a look at the HDD Status.

If status is "Connected", press red button to reboot you decoder.

Wait until the box is on, then try to record any program.

‍

If issue persist, please submit the issue on our Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

If status is "Disconnected", please submit your Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

Your documents will be handled in compliance with standards set by PDPA (Personal Data Protection Act 2010) and will not be used for other means without your specific consent.

Should there be any changes in plans we will keep our customers informed on any new development.

You can now choose to log in using your email address, mobile number or a social account (Facebook, Google or Apple).

There are 2 methods of setting maturity ratings restriction on Netflix: 

‍

Method 1 – Create a Kids Profile in Netflix App on Ultra/Ulti Box 

1. On the Netflix home menu, select “Switch Profile” 

2. Select Add Profile.  

3. Name the profile. 

4. Select Kids. Kids profiles have a logo 'Kids' on the profile icon so they are easy to identify.  

5. Select Continue. The new profile will show on the list of profiles on your account. 

‍

Method 2 – Manually set Viewing Restrictions for each profile 

1. Go to https://www.netflix.com/profiles/manage

2. Select a Profile. 

3. Under Maturity Settings, select Edit. 

4. Enter your Netflix password. 

5. You may select the desired Maturity Rating settings or add a particular title restrictions for the profile. 

6. Select Save. 

For more information kindly visit: 

• https://help.netflix.com/en/node/114275

• https://help.netflix.com/en/node/114276

The recommended home internet speed for a smooth viewing is 10Mbps.

1. Clearly indicate full name of Astro customer, contact number and Astro subscription account number when making each payment (e.g. on bank-in slips)
2. For Direct Debit, please contact your bank for standing instructions. Provide the full name of Astro customer and Astro account number. The Direct Debit service may not be available with all banks. Please check with your bank for confirmation of Direct Debit service.
3. Please inform us of any changes in billing address/information by contacting us via one of these platforms.

IMPORTANT NOTICE: To avoid any problems in payment processing, please pay only at authorised Astro payment channels

STEP 1

‍

Try to change channels on your Astro  remote.

INDICATOR: LED blinking 3 times / NO LED blink

SOLUTION: Replace new battery

Proceed to Step 2.

‍

INDICATOR: LED blinking 1 time

Confirm it's not your Astro remote faulty, let's proceed to Step 3.

‍

STEP 2

If issue remain after the battery replacement, this might be due to a faulty Astro remote.

Try changing the channel manually directly from the box front panel (If any).

If it's working, you might need to  replace your Astro remote.

You may walk-in to our nearest Customer Service Center for the replacement.

STEP 3

You need to refresh the box setting by initiate manually from box front panel.    

Refer to Refresh Box setting Guide steps here.

The payment will take some time to reflect in My Astro app and web account. If you experience any further issues or it is still not reflecting in My Astro, please reach out to us via WhatsApp at 03-9543 3838 for more details.

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required  screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info

A Ping Test shows how long it takes for packets to reach host.

A Traceroute Test traces the route of packets to destination host from our server.

Intermittent  internet connection using Wi-Fi

1. Router Positioning

Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.

i) High vs. Low

Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the  router of possible interferences.

ii) Concrete & Metals

Make sure your router isn't blocked by  any other objects, especially devices that are electronic. Also, avoid  placing your router in your basement as this area is usually enclosed by a  lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.

iii) Distance to Router

The further away from your router you  get, the weaker the Wi-Fi signal. Therefore, the best option is to place your  router as close to your devices as possible, but this is only practical if  you have one main area where you tend to use your devices.

Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put  it at one end of the house.

2.  Wireless Interference & Noise

You've probably never noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.

Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:

i) Microwaves

ii) Bluetooth Devices

iii) Cordless Phone

3.  Surrounding Wi-Fi signals

A truth of the modern world is that every  household has their own Wi-Fi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many routers within close proximity.

Which is why it's important that you pick a good channel in your  router settings. Modern routers can choose channels for you automatically,  but sometimes it's better to investigate and find the best channel yourself.

4. Usage

More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.

Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem  persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required  screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick  Info

A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.

A Ping Test shows how long it takes for packets to reach host.

A Traceroute Test traces the route of packets to destination host from our server.

Refund fee is subject to your processing bank. However, Astro did not impose refund processing fee.

electronic Know-Your-Customer (eKYC) is an online process of identifying and verifying individual customers using electronic means. This enables a person to be an Astro customer anytime and anywhere, hassle-free and helps to secure your Astro account by protecting it from unauthorised usage.

Step 1: Download the My Astro app from either the App Store, Google Play or HUAWEI AppGallery.

Step 2: Sign in with your Astro ID.

Step 3: Select "Rewards" on the home screen to get started.

Watch this tutorial to learn how to create your Astro ID.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)
 

Username: admin
Password: admin (or time123)

 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

• On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab

• Please ensure Wireless RF Mode is Enabled.

• Click the drop-down arrow for Channel, then select your desired channel.
• Choose between 1 until 11 (Suggested 1,6,11).

• Click Submit. Router will auto reboot and connection re-establish after few minutes.

Astro Fibre subscription also comes with a 24-month contract commitment and will NOT be auto renewed at the end of contact period.

Auto-debit payment will be debited from your account 5-7 working days after your billing cycle date.
If your auto-debit payment is unsuccessful, you will receive an SMS alert.

Kindly ensure that your mobile number is the same as the registered phone number of the Astro account holder as the OTP will only be sent to the registered number. For further assistance, please call or WhatsApp us at 03-9543 3838. Alternatively, you may submit a request via our online Feedback Form here: astro.com.my/contactus/form.aspx. 

Astro TV customers

No, you will not be required to take on a new contract after moving. If you still have an existing contract, the contract will continue.

‍

Broadband / IPTV customers

Yes, your contract will be renewed to a new 24-month contract.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Navigate to IP Diagnostics and press "OK".

STEP 5    

IP Diagnostics information will be displayed.

Please contact your issuing bank to enable card-not-present (CNP) transactions. This security measure helps us to protect your card information from being misused in fraudulent transactions.

You may retain your watch history and settings of your existing Netflix account by using the same email of your Netflix account during the linking of your Netflix account with Astro.

You can track your ticket status by contacting us via WhatsApp or call us at 03-9543 3838.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the Smartcard at the front or right side and gently pull it out make sure that the adapter's power light is off.

STEP 3

Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be  experiencing this problem.

If issue persist, please submit your feedback form with error details and attach a picture of your sim card number for assistance.

No, Astro First movies/series are available as Per-per-view basis. Pricing is indicated on each of the programme posters. All prices are subjected to 6% service tax.

Yes, your advance payment will be fully refunded if you cancel your subscription before the Astro box installation. Please call Astro's Contact Centre at 03-9543 3838 for a refund. The refund process will take approximately 14 days for processing with your issuing bank. However, if you decide to cancel your subscription after the Astro box installation (during your contract period), the prorated early termination fee will apply.

Not all shows/channels will be available on Astro GO as this depends on contractual rights with specific guidelines on the entitlement of these shows/channels and what you have as a part of your subscription. 

Below are channels that are not available on Astro GO:

1. TV3
2. TAYANGAN HEBAT HD
3. ART
4. NTV7
5. 8TV
6. TV9
7. VELLITHIRAI
8. AWESOME TV
9. STAR CHINESE CHANNEL
10. ARABIC RADIO & TV VARIETY
11. NJOI TV
12. NHK WORLD HD
13. FX HD
14. ASTRO BEST / FIRSTCHANNELS

Please be assured that Astro is continuously working on getting more content available on Astro GO.

Users can easily access all their streaming Apps such as Netflix, Disney+ Hotstar, Viu etc by clicking the “APPS” button on their remote control. After clicking this button, they will be brought to the Apps rail under the home page.