There will be no penalty imposed upon the removal of Astro GO+ from your subscription.

We would need you to  run few tests in order for us to understand your issue and to assist you in fixing the problem.

You may proceed with the troubleshooting steps below which should not require any longer than 15 minutes.

1. Please run each of the tests according to your your Laptop/PC Software.
2. Compile the pictures / screenshots of your test results in one file (i.e Microsof Word document, PDF file) and attach them in the Support Ticket below in order for us to assist you further:
   • List of websites effected.
   • Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.
   • Run the Traceroute Test - Please click here for Traceroute Test guideline.          
   • Run the Ping Test - Please click here for Ping Test guideline.
3. Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.

A Ping Test shows how long it takes for packets to reach host.

A Traceroute Test traces the route of packets to destination host from our server.

WiFi router and fibre modem will be replaced upon checking and verification by Astro's Contact Centre /installer. It will be replaced without additional charge regardless contract tenure.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Video Resolution and press “OK”.

STEP 4

Navigate to your preferred selection and press “OK”.

Recommended to select Auto.

STEP 5

Navigate to Save and press "OK" to confirm your selection if able to read the text properly.

Otherwise, navigate to Cancel to revert to previous settings.

STEP 1

On your remote, press the “HOME” button and the home menu will  be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB  DIAGNOSTICS and press “OK”.

‍

STEP 4

Select the “Network” tab in the STB Diagnostics page.

Please ensure the Tunes service multicast  status is Multicast Up.

If the status is Multicast is Not Available, please reboot your box and router before verifying this status.

If issue persists, please submit the issue in our Feedback Form and attach a picture of your Network tab of the STB Diagnostics for assistance.

STEP 1
On your remote, press the HOME button and the menu will be displayed on top of your screen.
STEP 2
Navigate to Settings.


STEP 3
Navigate to Network Settings and press “OK”.


STEP 4
Navigate to Test Connection and press “OK”.


STEP 5
Test Connection results will be displayed on the screen.

For Ultra/Ulti Plug & Play Box installation, it is recommended that you attempt to self-install by following the installation guide here, but there is an option to request for an installer to install the box at your premise. However, there will be a separate fee for this service request.

Please contact us through one of our platforms found here or Self-serve by logging in to Astro Self-Service Portal within 3-7 days before moving out and we will sort everything out for you!

Yes, Mesh WiFi add-on is available for both Astro Fibre Bundle and Astro Fibre subscription.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.

1. Try  loading the site on a different device.

  Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.

  If the website doesn't load on another device, the problem is either with the network or the website itself.

2. Restart your computer.

  Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.

3. Try loading the site in a different browser.

  There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.

4. Temporarily disable your antivirus program.

  Your antivirus software may be interfering with your ability to load certain websites.

  Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.

5. Reset  your modem and router.

  Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.

6. Check  your computer's date and time settings.

  If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.

  Check your computer or mobile device's clock to make sure that it is set to the correct time and date.

In the  event the problem persists, please provide below details for further  escalation:

  i. List of websites effected.          

  ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.  

  iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.          

  iv. Run the Ping Test -  Please click here for Ping Test guideline.

 Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

Settlement of total outstanding balance is to be made prior to any of the request.

Your Astro GO email will be delivered to you within an hour upon checkout. Please click the link provided to set up your password and download the Astro GO app on your device by clicking here (Google Play Store) or here (iOS App Store). If you want to stream it directly via your computer or laptop, Astro GO is also available at astrogo.astro.com.my. Log in with your Astro ID and start streaming!

Service will resume within 3 hours after payment is made.

1) Download the Astro app from the app store available on your Smart TV.

2) Follow the steps below depending on your Smart TV brand.

1. Power reset (on & off) your TV, Astro Decoder, Modem and Router.

2. Ensure standard physical connection (No 3rd party devices connected to decoder and modem).

3. Please ensure at all-time your router is 0.5 meter away from your Astro Decoder to avoid signal interferences.

4. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [connect the LAN (cable) at any LAN port at router and direct to computer/laptop].

5. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

6. On the address bar, please go to http://www.speedtest.net/ and below page will appear.

7. Click "Change Server" to edit the settings preferred by Internet Service Provider (ISP).

8. Edit the server settings by search and select the required server required by ISP.

    For Maxis provider - Select Subang Jaya - Maxis server.

    For TIME provider -  Select Shah Alam - TIME dotcom Bhd server.      

    For Allo provider -  Select Cyberjaya - Global Forway Sdn Bhd server.

9.Click "GO", and the test will  begin.

The test is completed once both download and upload speeds are displayed.

Sample of the Speedtest result is shown below.

**Please  ensure the snapshot includes a time stamp and network used either LAN cable  or wireless (as per picture above)

10. Kindly screenshot or take a picture of the result, name it as "LAN Speedtest".

11. Repeat the test once again using Wi-Fi connection (Please unplug your LAN cable and connect via wireless connection using your SSID).

12. Screenshot or take a picture of the  result, name it as "WiFi Speedtest".

Yes, you can sign up for auto-debit after your account has been activated via My Astro.
 
Alternatively, you may also call our Customer Contact Centre at 03-9543 3838 for assistance or to enquire about any current Auto Debit promotions.

Multiroom (Astro Box) requires an Astro box to be setup and can be accessed through the regular satellite feed or streaming on home Wi-Fi. Meanwhile, the Multiroom (Smart TV) only requires a Smart TV and no installation needed. Customers can download the Astro app on the Smart TV and connect to home Wi-Fi to stream.

STEP 1  

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3  

Navigate to Display and press "OK".

STEP 4    

Navigate to Resolution and press "OK".

STEP 5    

Navigate to your preferred selection and press “OK”.

STEP 6    

Select Yes, continue and press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)
 

Username: admin
Password: admin (or time123)

 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

• On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab

• Please ensure Wireless RF Mode is Enabled.

• Click the drop-down arrow for Channel, then select your desired channel.
• Choose between 1 until 11 (Suggested 1,6,11).

• Click Submit. Router will auto reboot and connection re-establish after few minutes.

The minimum internet speed required to stream via Ultra Plug & Play Box is 30Mbps for 4K UHD viewing, and Ultra/Ulti Plug & Play is 10Mbps for HD viewing. For better streaming experience, we recommend 100Mbps and above.

For Residential Astro Pay TV customers: Yes, you are allowed to change your package to the one that best suits your entertainment needs. You may make the following pack changes:  

1. Pack upgrades

1. Movement within Entertainment, Movies or Sports (e.g., switching from Sports to Entertainment)

1. Movement within Premium pack (to a different combination of content)

For these changes, you will remain on same contract duration, or you can choose to change to longer commitment. If you downgrade your packs, you will be charged a cancellation fee for pack, and you can then choose a new contract for the new pack. Kindly note additional contract details for Disney+ Hotstar and Netflix.  

(Please refer to the section "Changes to your Astro Contract" for more details)

No, the Astro Fibre App is a free mobile application for all Astro Fibre customers with the latest RG21 router.

You can proceed with below troubleshooting if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4

Refer to the signal strength % shown on the top left of your screen.

If it is 65% or higher, please take the screenshot and submit your Feedback Form.

If it is below 65%, please go to Step 5.

STEP 5

Switch off the power for your box and make sure that the adapter’s power light is off.

‍STEP 6

Unscrew the satellite cable from the box and pull it out.

STEP 7

Plug the satellite cable back into the box and screw it back securely.

STEP 8

Switch on the power for your box and make sure that the adapter’s power light is on.

Please wait for 5 minutes.

STEP 9

Turn on your box. You should no longer be experiencing this issue.

‍

If issue persist, please submit the issue on our Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

‍

Centralized Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

No, there are no penalty fees for the Mesh WiFi devices should you wish to terminate Astro Fibre within/after 24 months. 

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

Yes, you will need to pay additional RM25 per remaining contract months per unit on top of the standard Broadband penalty fee should you terminate the contract within 24 months.

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required  screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info

A Ping Test shows how long it takes for packets to reach host.

A Traceroute Test traces the route of packets to destination host from our server.

Intermittent  internet connection using Wi-Fi

1. Router Positioning

Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.

i) High vs. Low

Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the  router of possible interferences.

ii) Concrete & Metals

Make sure your router isn't blocked by  any other objects, especially devices that are electronic. Also, avoid  placing your router in your basement as this area is usually enclosed by a  lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.

iii) Distance to Router

The further away from your router you  get, the weaker the Wi-Fi signal. Therefore, the best option is to place your  router as close to your devices as possible, but this is only practical if  you have one main area where you tend to use your devices.

Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put  it at one end of the house.

2.  Wireless Interference & Noise

You've probably never noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.

Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:

i) Microwaves

ii) Bluetooth Devices

iii) Cordless Phone

3.  Surrounding Wi-Fi signals

A truth of the modern world is that every  household has their own Wi-Fi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many routers within close proximity.

Which is why it's important that you pick a good channel in your  router settings. Modern routers can choose channels for you automatically,  but sometimes it's better to investigate and find the best channel yourself.

4. Usage

More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.

Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem  persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required  screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick  Info

A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.

A Ping Test shows how long it takes for packets to reach host.

A Traceroute Test traces the route of packets to destination host from our server.

If you accidently clicked “delete my account” on the Astro Fibre app, you will bedirected to submit a request via Feedback Form as the image below.

If you submit a request, our Astro representative will get back to you within 3 business days to learn more about the issue(s) you are currently facing with the app. Customers may proceed to permanently delete their account during the call if they wish. Once complete, your Astro ID will be deleted and you will be unlinked from all Astro apps and services including partner apps that are associated with your Astro ID including Astro GO, My Astro, Astro Awani, Syok, beIN SPORTS CONNECT, iQIYI, TVBAnywhere+,HBO GO, Gempak, XUAN, Astro Ulagam etc.

You may create another Astro ID by following the steps here and re-link your new account to all Astro apps and services, including partner apps.

Your bill statement will include details of your monthly subscription charges; e.g. charges for your chosen Astro packages and Broadband service. It will also show the time period of which your first bill will cover, as well as indicate how much the total charges are and when the payment due date is.

For more info on the product including offers and setup, visit product.astro.com.my/multiroom

STEP 1
Please wait while your Astro box initializes.



STEP 2
Select your preferred language.



STEP 3
Navigate to Next and press "OK".



STEP 4
Select Auto as the Video Resolution.



STEP 5
Navigate to Next and press "OK".



STEP 6
Navigate to Confirm and press "OK" to confirm your selection if you are able to read the texts on screen properly.
Otherwise, navigate to Cancel to revert to the previous settings.



STEP 7
Select Satellite as the box operating mode.



STEP 8
Navigate to Next and press "OK".



STEP 9
Select your preferred connection.
For connection via Wi-Fi, proceed to STEP 10.
For connection via LAN Cable, proceed to STEP 16 once you are connected.



STEP 10
Please wait while your Astro box searches for available Wi-Fi networks.



STEP 11
Navigate to your preferred Wi-Fi network and press "OK".



STEP 12
Please enter the password to connect to the Wi-Fi network.



STEP 13
Navigate to Done to continue.



STEP 14
Please wait while your Astro box connects to the internet.



STEP 15
Navigate to Yes to allow your Astro box to connect to this network automatically.
Otherwise, navigate to No.
Proceed to STEP 17 for the next step.



STEP 16
Navigate to Next and press "OK". 



STEP 17
Navigate to Universal.



STEP 18
Navigate to Next and press "OK".



STEP 19
Select 01 M3B VL - 10732 as the Entry Point.



STEP 20
Navigate to Next and press "OK".



STEP 21
Please wait until the signal reading is updated.
Navigate to Finish and press "OK" to complete the settings.

Only the account holder is allowed to manage the auto-debit facility. However, a third-party card holder has the right to withdraw their registered card from the linked-account with proper validation.

STEP 1

Check on your TV input to ensure correct input selected.

If issue remains, switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Unplug the HDMI cable from your box and plug it back in securely.

STEP 3

Switch on the power for your box and make sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 4

Turn on your box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form with the error details and provide  sim card number for assistance.

You have exceeded the maximum number of registered devices allowed. To manage devices on Astro GO, go to Settings > Registered Devices to view / remove devices from the list of registered devices to your account.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.
 

Please upgrade the Ultra/Ulti Box software to enjoy Netflix on your Ultra/Ulti Box. To do this, please click on the Netflix app icon on the homepage or go to CH741 to prompt the software upgrade. Kindly click Install when the software upgrade prompt appears. This will take approximately 20 minutes and you would be able to launch Netflix on the Ultra/Ulti Box after that.

No, you can remain in your current pack, however starting 9 November 2021, you would need to subscribe to the new packages to make any changes to your subscription. We strongly encourage customers to switch to the new packs to enjoy the best content experience from Astro.

You are entitled for free mesh WiFi devices when you sign up for Astro & Broadband with Maxis fibre 500Mbps or 800Mbps speed only.

Mesh WiFi is not available with Astro & Broadband with Allo. However, you may purchase the Mesh WiFi devices separately to pair along with you Allo broadband.

Further details on pricing, billing and availability will be confirmed in coming months. Look out for more details and register your interest via https://astro.com.my/Netflix

Please visit any of Astro’s digital platform that you would like to log into, such as Astro’s official website (www.astro.com.my). Then, create a new Astro ID using your email address or mobile number by clicking “No Astro ID? Create Now!”. After creating your new Astro ID, please use it to log into our digital platforms moving forward.
 
If you have an active Astro subscription, you may also link it to your Astro ID. Please click here for the guide.
 

1. Ensure power cable is connected tightly.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

You can make changes to your Netflix plans that are included in your Bundle through My Astro app 

You can change your non Astro-bundled a-la carte Netflix plan at any time by signing into Netflix.com and visiting the Account page, then selecting Change Plan to view and select available plans.  

We are working with the Sony team to ensure you will be able to enjoy these 4K UHD channels soon. We will keep you posted once these channels are available to you!

Yes, until 31 August 2022, customers can subscribe to the Movies Pack for only *RM59.99/month or the Platinum Pack for only *RM99.99/month for 6 months as well as the Premium 1 or Premium 3 Pack for only *RM99.99/month for 6 months until 30 October 2022 and be entitled to access Disney+ Hotstar as part of their Astro subscription. To find out more about our latest promotions, please visit promotions.astro.com.my.