Please use your Astro ID to log in to the Astro Fibre App. If you do not have an Astro ID, kindly follow the simple steps here to create one.

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

From Channels 480 (Astro First):

1. ‍Go to channel 480
2. Search for the Movie title or Series and press “OK” button from Astro remote control;
3. Choose how to purchase via WhatsApp or SMS.
4. Enter the Pin Code

Purchase via Whatsapp

1. ‍Go to channel 480‍
2. Whatsapp the “movie code” to 03-9543 3838 
3. Enter your “smart card number” (this is available on the top right corner of your tv screen)‍
4. Type “1” to confirm
5. The reply will direct you to the entitlement channel accordingly

Purchase via SMS

1. ‍Go to channel 480‍
2. SMS the “movie code” to 32999 ‍
3. The SMS confirmation reply will direct you to the entitlement channel accordingly

*SMS service is available for Maxis, Celcom, Digi and U Mobile only.

‍

From Beyond PVR On Demand interface:

1. Press the “Home” button on the Astro remote control
2. Select “On Demand” and press the “OK” button from the Astro remote control
3. Scroll to “Store” and search for the Movies/series
4. Select “Buy” and enter Pin Code. 

‍

From Ultra/Ulti On Demand interface:

1. ‍Press the “Home” button on the Astro remote control 
2. Scroll to the Store tab
3. Scroll to “Astro First: New Releases” or “Astro First: Blockbusters” and search for the Movies
4. Select “Rent” and enter Pin Code

‍

From Astro Go app (purchases only applicable for Android devices): 

1. ‍Download the Astro Go app from the Google Play store.
2. Create an ID and link your account / proceed to log in if you have linked your account
3. Scroll to “Store” and search for “Astro First: New Releases” or “Astro First: Blockbusters”
4. Select “Rent” and enter Pin Code

*The default pin code is 0000 if you have not pre-set it.

For more info on the product including offers and setup, visit product.astro.com.my/multiroom

No, there will be no additional charges to access Liga Malaysia.

Disney+ Hotstar is available on Chromecast (Gen 2 onwards, firmware 1.43 & above) and with the latest version of the Disney+ Hotstar app on iPhone, iPad and Android mobile. 

Follow these instructions to cast your film/series: 

• Make sure your mobile device and your Chromecast are on the same WiFi network 
• Log into your Disney+ Hotstar app 
• Select a film/series that you want to cast 
• Press "Play' 
• Once the film/series has started, tap on the casting icon 
• Select the screen you wish to cast to 
• The film/series should then be cast onto your screen

Successful payment via JomPAY will be posted real time.

You need to identify your modem type by looking at the modem light indicator before proceeding with troubleshooting.

The type of modem is indicated as per below:

MODEM INDICATOR 1



MODEM INDICATOR 2




MODEM INDICATOR 3



BTS 1

1. Please power off your modem and router. (This is to refresh your modem and router performance)
2. Make sure the fibre cable from your wall socket to modem is securely connected.

3. Please ensure the LAN cable is securely connected from router to your devices (Astro Box/Laptop etc.)

Modem connection

   

Router connection



4. Now, power on modem and router, wait for 2 minutes to stabilise the devices after reboot. Your internet services should be restored.

5. If issue persists, please connect to our agent and attach your modem light indicator picture for further assistance.



BTS 2

1. Please power off your modem and router. 
    (This is to refresh your modem and router performance)

2. Make sure the fibre cable from your wall socket to modem is securely connected.



3. Please ensure both LAN cables on the Modem (LAN Port 2) and Router (Port 1) are properly connected.


Modem connection


   
Router connection


4. Power on your modem and router, wait for 2 minutes to stabilise the devices after reboot. Your internet services should be restored.

5. If issue persists, please connect to our agent and attach your modem light indicator picture for further assistance.



BTS 3

1. Please ensure your modem and router power plugs are securely connected to the power socket.



2. Alternatively, try to connect the power plug to a different power socket or power source. This step is to eliminate the possibility of faulty power socket which could cause the issue.

3. If issue persists, please connect to our agent for further assistance.

There will be no changes to your Netflix account when you move to a new address.

Your documents will be handled in compliance with standards set by PDPA (Personal Data Protection Act 2010) and will not be used for other means without your specific consent.

Yes, any active Astro subscriber with a minimum primary subscription fee of RM100 can subscribe to a Multiroom (Astro Box) at a price of RM49.99 monthly with the box setup (subscription price is subject to Govt Tax).

Refund fee is subject to your processing bank. However, Astro did not impose refund processing fee.

Tap on the "Account' screen on the navigation bar to view your outstanding balance. Click on "Pay Now' to pay your bill. If your payment is successful, you will receive a record and your payment history will be updated.

You will be able to access Netflix on your Ultra and Ulti Box. However, kindly note that if you have an Ulti Box with a Netflix Premium subscription, you will not be able to watch content in 4K UHD and Netflix Spatial Audio.

Band Steering is a functionality that our WiFi router (Huawei K562E) has that intelligently connects devices to its WiFi to the best frequency bands available based on usage, speed and coverage by using only one same SSID for both 2.4GHz and 5GHz band.

Service will be resumed after you make payment within 45 days. The monthly subscription fee to be prorated accordingly and a reconnection fee of up to RM20 (exclusive of SST) will be applied upon service resumption. 

If payment is made within 45 days from your bill cycle date, Astro & Broadband services will be resumed within 3 hours of payment received. Your following month's bill will be prorated accordingly.

Find out more about the reconnection fee here.

The WiFi SSID and password of the Mesh unit will be automatically synchronized to the WiFi router. Hence, there is no need to configure the WiFi parameters.

*WiFi SSID (Service Set Identifier) is the name of your wireless network, also known as Network ID. It is viewable to anyone with a wireless device within reachable distance of your network.

Your account may be under suspension. To resolve this issue, proceed to submit report via WhatsApp or Feedback Form.

Users can easily access all their streaming Apps such as Netflix, Disney+ Hotstar, Viu etc by clicking the “APPS” button on their remote control. After clicking this button, they will be brought to the Apps rail under the home page.

 

electronic Know-Your-Customer (eKYC) is an online process of identifying and verifying individual customers using electronic means. This enables a person to be an Astro customer anytime and anywhere, hassle-free and helps to secure your Astro account by protecting it from unauthorised usage.

The minimum internet speed required to stream via Ultra Plug & Play Box is 30Mbps for 4K UHD viewing, and Ultra/Ulti Plug & Play is 10Mbps for HD viewing. For better streaming experience, we recommend 100Mbps and above.

Mac OS X

1. Click the Go tab in the top menu bar and select Utilities from the drop-down menu.

2. Type "network utility" in the search bar in the top right-hand corner of the Utilities window and then hit the "Enter" key on your keyboard. 

3. Click the Network Utility icon to open the Network Utility window.

4. For Ping Test, select the Ping tab and then type the address you'd like to ping in the text box. Click Ping and wait for the ping results.
 

5. For Traceroute Test, select the Traceroute tab and then type the address you like to traceroute in the text box. Click Trace and wait for the traceroute results.
 

Windows 10

1. Click the Search icon (magnifying glass) in the bottom left-hand corner and type "cmd" into the search bar.

2. Select the Command Prompt app - it will be at the top of the list of search results as the best match.

3. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

Windows 7 & Vista

1. Open the Start menu by clicking the Windows icon at the bottom left-hand corner of the screen.

2. Type "cmd" in the search bar at the  bottom of the menu.

3. Click cmd found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows 8

1. Move the mouse to the right-hand corner of the screen to make the vertical menu bar (charm bar) appear. Click Search.

2. Type "cmd" in the search bar and hit the Enter key on your keyboard.

3. Click cmd that found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows XP

1. Click the Start button in the bottom left-hand corner of the screen.

2. Click the Run option in the right-hand column.

3. Type "cmd" in the text box and then hit the Enter key on your keyboard.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you'd like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.