Astro GO+ is a service add-on that: 

• Enables the simultaneous viewing of Astro GO for up to 4 users/devices. 
• Increases the cloud recording storage from 200 hours up to 1500 hours. 

By default, the band steering featured is disabled. Follow these steps to enable it.

Note: Band Steering is called Dual-band Combination in the router web interface.

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).
2. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user
Password: user

 

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi to configure the WiFi parameters.

6. Click on Dual-band Combination button to enable the Band Steering.

7. A pop-up message will appear showing "The device network may be disconnected when dual-band combination is enabled". Click "OK" to proceed.

8. Set the Wi-Fi name and Wi-Fi password based on customer's preferences. Then click "Apply" for the changes to take place.

Please reconnect to the new Wi-Fi name with the new password once completed.

Only the account holder is allowed to manage the auto-debit facility. However, a third-party card holder has the right to withdraw their registered card from the linked-account with proper validation.

No. Astro GO is a FREE entitlement exclusively for customers with an Astro subscription. If you do not have an Astro subscription account, please visit astro.com.my to find out more.

It will begin on 1st March 2024 and onwards.
 

Your Astro account number is a 10-digit combination 
E.g: 08XXXXXXXX

Please make sure that:

1. You are logging in with the correct registered Astro ID (email or phone number) and password. If you can’t remember your password, please proceed to use the “forget password” function.
2. You have an Astro ID that is linked to an Astro account. (note: NJOI – linked users will not be able to log into Astro GO)
3. Your Astro account is active and not under suspension.

If the above points have been met, you may try some quick solutions below:

1. Clear the cache on your browser or app.
2. Check if you have the latest version of the browser or app.
3. Log out and log back into the browser or app.
4. Relaunch the browser or app.
5. Restart your mobile device.
6. Restart your internet connection.

Yes. You are entitled to separate Netflix accounts for each main Astro subscription e.g. If you have subscribed to Entertainment Plus, Platinum Pack, etc separately. Therefore, if you have more than one main Astro subscription with Netflix, you may choose to create multiple email addresses to activate each respective Netflix subscription. Please follow the steps provided to you via email/SMS in order to activate your Netflix subscriptions on the website.

Not to worry, you will only need to verify your Astro ID once. After that, you may log in to your account as usual.

No, you will not be able to manage your account with the Astro Fibre App. However, you may download the “MyAstro” app on your mobile device now to manage your Astro account in a fast and easy way.

Please visit http://help.netflix.com to call or start a live chat with Netflix's customer support agents. You will be assisted to unlink your Netflix account from your Astro subscription. After the process, you may link another Netflix account to your Astro subscription.

Unfortunately, you cannot link your direct Disney+ Hotstar subscription to your Astro account. Please ensure that the mobile number used for your direct subscription to Disney+ Hotstar is different from the mobile number used to activate Disney+ Hotstar entitlement via your Astro subscription. If you do not have an alternative mobile number to nominate, kindly contact Disney+ Hotstar's customer service directly at disneyplus.my@hotstar.com for details on how to cancel your direct subscription. 

If you are facing technical issues, please contact us at wecare@astro.com.my or call/WhatsApp us at 03-9543 3838.

There will be no installation fee for both Astro Box and Ultra Box. The Multiroom (second decoder) must be installed at the same registered address as your primary subscription.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.
you may have to get your hands a little dirty.
 

1. Try loading the site on a different device.
   • Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.
   • If the website doesn't load on another device, the problem is either with the network or the website itself.
2. Restart your computer.
   • ​​Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.
3. Try loading the site in a different browser.
   • There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.
4. Temporarily disable your antivirus program.
   • Your antivirus software may be interfering with your ability to load certain websites.
   • Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.
5. Reset your modem and router.
   • Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.
6. Check your computer's date and time settings.
   • If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.
   • Check your computer or mobile device's clock to make sure that it is  set to the correct time and date.
7. In the event the problem persists, please provide below details for further escalation:
   • List of websites effected.
   • Run the Speed Test  via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.
   • Run the Traceroute Test - Please click here for Traceroute Test guideline.
   • Run the Ping Test -  Please click here for Ping Test guideline.
   • Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

Connect your Ultra Box/Ulti Box today and get the full value for your subscription. We believe we can provide you the best entertainment experience in Malaysia, and it all starts with connecting your box to the internet.

Want to enjoy these features for free?

• Continue watching Astro even when it’s raining.
• Binge-watch and catch-up to 110,000 videos on-demand from Malaysia, Hollywood, Korea, China, Bollywood and more anytime.
• Create multiple profiles in your house to enjoy a personalized Astro experience, with shows recommended to you based on your interest. There is a Kids-friendly version for your little ones as well.
• Rewind, pause and fast-forward shows and matches so that you will never miss another moment.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Scroll to Network Settings and press "OK". Select New Wi-Fi Connection and press "OK".

‍

STEP 4

Select your Wi-Fi network and press "OK". Please enter the password to connect to your network.

STEP 5

You have successfully connected when this screen appears.

Astro Rewards is open to all *Active Astro PayTV customers and their immediate family members

* "Active Astro customer" refers to subscriber of the Astro Service and whose account is current and active with no outstanding payments due and owing to Astro and who has not breached the Astro subscription agreement nor given any instructions to terminate and /or suspend his/her subscription to the Astro Service as at the date of winner notification. Winners must remain active Astro customers until the date of collection of prizes.

Yes, existing Astro customers can subscribe to all Astro & Broadband offerings. 24 months contract will be renewed upon signing up for broadband.

There are a few ways you can access Netflix on the Ultra Box as below: 

• Access Netflix on the Ultra/Ulti Box via the Home Screen and select the Netflix app from the Apps row. 
• Launch the Netflix app directly from their remote control by clicking on the “Netflix” button if it’s available on your remote control. 
• Tune into CH 741

IMPORTANT! If you are accessing Netflix on your Ultra/Ulti Box for the first time, please wait for the Netflix activation email from Astro (this may take up to 10 minutes) for the app to be reflected in your account. If you skip this 10-minute period, you may experience double charging by incorrectly signing up for Netflix using your credit card details.

You can subscribe to new packs via  

• Online - astro.com.my  
• WhatsApp GET ASTRO (for new customers) or SWITCH (for existing customers) to 03-9543 3838
• Astro Customer Service Centres.

No additional subscription is required. Video On-Demand (VOD) is a value-added service for all Astrro customers with connected Astro boxes (Ultra Box, Ulti Box, HD-PVR & PVR boxes). All you have to do is connect your decoder to your home Wi-Fi and you'll be able to access the world of on demand. Binge-watch, rewind, fast-froward and stream all your favourite shows anytime.

STEP 1  

Press "HOME" button on your remote control.

STEP 2

Navigate to Update Satellite Frequency and press “OK”.

‍

STEP 3    

Choose Reprogramming and press “OK”.

STEP 4    

Select Yes, continue and press "OK" to proceed with the update.      

Otherwise, select No, go back to cancel.

STEP 5  

Satellite Frequency Update progress screen will be displayed.

‍

STEP 6    

The test result will be displayed once completed.    

Press "OK" to go back to  channel.

Unfortunately, this means that you are using a TV model that does not support 4K UHD resolution (Sony BRAVIA 4K GB, Sony BRAVIA 4K UR or Sony BRAVIA VH). Not to worry, we are working with the Sony team to ensure you will be able to enjoy these 4K UHD channels soon. We will keep you posted once these channels are available to you!

Please follow the steps below to retrieve your Astro ID:



Note: Only Astro customers whose Astro ID is linked to their subscription can retrieve their Astro ID this way. Otherwise, you would need to create a new account.
 

STEP 1
Switch off the power for your box and  make sure that the adapter's power light is off.

STEP 2
Locate the Smartcard at the front or right side and gently pull it out make sure that the adapter's power light is off.

STEP 3
Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4
Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5
Switch on the power for your box and make sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 6
Turn on your box. You should no longer be experiencing this problem.
If issue persist, please submit the issue in our Feedback Form and attach a picture of your General tab of the STB Diagnostics  for assistance.

Yes, the Multiroom (Smart TV) will utilise one (1) of your Astro GO concurrency.

Customers subscribing to Multiroom (Smart TV) can enjoy access up to 4 concurrency (watch 4 screens at the same time) which is shared across one Smart TV device and 3 mobile/laptop/tablet device(s) as Astro GO+ is complimentary with a Multiroom (Smart TV) subscription.

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

The Kids Friendly Profile is an enhancement to the Kids User Profile feature with the following major improvements:

Kid-Friendly Channels, On Demand content & TV Guide: Only Kid-friendly channels and On-Demand content can be viewed in the Kids Profile. Other channels and content are not viewable. The same applies to the Kids TV Guide.
1. PIN control for the Kids Profile:  When switching from a Kids Profile to an adult profile (i.e.: Father or Mother), a PIN entry will be required.
2. Limited Kids Profile Content Search: Only Kids age-appropriate content can be searched and displayed within the Kids Profile.
3. Kids Profile Based Recordings: Kids Profiles will have their own personalised age-appropriate recordings without any overlap with other user profiles. This feature will be available from 17th August onwards.

These enhancements are available across the Astro GO app, Ultra/Ulti Box, and Multiroom Box/Smart TV app.

Click here to find out more on this new feature and how to use it!

If you are already subscribed to the Movies/Premium 1/Premium 3/Platinum Pack, you are automatically entitled to access Disney+ Hotstar. Therefore, you will not be able to add on the Disney+ Hotstar 3-months pass. 

We are not able to transfer your existing Disney+ Hotstar access. To enjoy our bundle rates with one of our packages, simply sign up or renew your subscription to any of our new Packs for even better value and savings. Please visit astro.com.my to find out more. 

Please check if you are streaming on a supported device. Astro GO is only applicable within the supported platforms; mobile devices (phones and tablets) and web browsers.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.

STEP 1
On your remote, press the Home button and the home menu will be displayed on your screen.



STEP 2
Navigate to Profile.



STEP 3
The Profile Selection Screen will be displayed.



STEP 4
Navigate to Edit Profile.



STEP 5
Choose a profile to edit.



STEP 6
Navigate to Name.



STEP 7
Enter your new Profile Name, navigate to DONE and press "OK".



STEP 8
Your new profile name will be shown in the Profile Selection Screen.


 

Please note that your request to opt out has been processed, and payment for Disney+ Hotstar is not required. Your bill adjustment will be reflected in your next bill. 

Please make sure that:

• You are inserting the correct account holder's information while linking, ie: I/C number, passport number, Astro account number or Smart card number.
• You are linking to an Astro account (NJOI customers will not be able to log into Astro GO).
• Your Astro account is not currently linked to any other Astro ID. If your Astro account is currently linked to another Astro ID, you will see a red notice.

To find out which Astro ID is currently linked to your account, you may submit a feedback form. Kindly select feedback type "I have an enquiry/issue with Apps

The balance will be credited into your account, which will be reflected when you receive your next bill. The balance credit will be used to offset your bill balance.

For Ultra/Ulti Plug & Play Box installation, it is recommended that you attempt to self-install by following the installation guide here, but there is an option to request for an installer to install the box at your premise. However, there will be a separate fee for this service request.

Yes, all existing Astro & Broadband customers within contract or out of contract can subscribe to Astro & Broadband offerings. The 24 months contract will be renewed upon signing up for the new packs.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your Ultra Box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

You must subscribe to an Astro subscription (NJOI customers are not eligible) in order to get the Ulti Box. 

‍

The eligibility criteria for the Ulti Box are as follows:

New Customers

All new Astro customers with a monthly subscription fee of below RM100 will be entitled to select the Ulti Box upon signing up for Astro’s packages. 

‍

Existing Customers (Box Upgrade for Primary or Multiroom)

Existing customers are required to have an internet connection at home with a recommended internet speed of 10Mbps and above in order to upgrade your existing box to Ulti Box. 

Note: 

·      Existing Ultra Box customers are not eligible for a swap to the Ulti Box.

·      If your existing box is a PVR, you will lose access to all the recordings stored in the PVR

‍

Multiroom (New subscription)

Customers subscribing for an additional multiroom subscription are entitled to select the Ulti Box as part of the subscription.

Please follow the steps below to verify your Astro ID:

 

STEP 1    

On your remote, press the Home button and the menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3    

Navigate to Restore and press "OK".

STEP 4    

Navigate to Restore Factory Settings and press "OK".

STEP 5

Enter your PIN to access this setting. (Default PIN is 0000).

STEP 6    

Navigate to Restore and  press "OK" to  confirm your selection.    

Otherwise, navigate to Cancel, go back to remain the settings.

STEP 7    

Please wait while the box restoring defaults and will reboot once complete.

STEP 8    

Your box will automatically restart and display this screen.

Click here to follow New Installation Settings guide for Satellite

Click here to follow New Installation Settings guide for Plug and Play

Multiroom (Smart TV) is a secondary subscription that allows you to enjoy your favourite Astro shows instantly in different rooms at the same time on your Smart TV. Subscribe to Multiroom (Smart TV) at RM29.99 per month (excl. any govt. tax), and simply download the Astro app on your second TV-screen and connect to your home Wi-Fi to stream.

This error indicates that you have reached the maximum number of simultaneous video streams across devices for one (1) account. To stop seeing this error, please stop streaming on one of your other devices.

• If you have recently purchased your Astro pack or made any changes to your pack on or after 9th November you can stream on two (2) concurrent screens

• If you have not made any changes you can stream on four (4) concurrent screens.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.
 

Upon successful subscription, you will be able to view your chosen HD channels within 3 hours by keying in the channel numbers into your remote control. Please note that subscription through Channel 200 will take effect within 24 hours.

Yes, you can upgrade your internet speed. However, speed downgrade is not allowed.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/ laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/ laptop].
2. You may open any web browser such as  Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)

Username: admin
Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the  configuration.

i. On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab.

ii. Please ensure Wireless RF Mode is Enabled.

iii. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

iv. Click Submit. Router will auto reboot and connection re-establish after few minutes.

The speeds shown under “My Network Map” are the WiFi speeds of your connected devices based on factors such as signal strength, distance of devices from your router, obstructing objects etc. This function allows users to know the signal strengths achievable from every room in their house or any distance from their router, giving users accurate indication If additional mesh is needed or if the placement of their router requires adjustment.

However, the speeds shown under “My Devices” are the recent WiFi consumption of your connected devices, which allows you to monitor every user’s internet consumption in your household.