Please refer below to set up your Ultra/Ulti Plug & Play Box.

To connect via LAN cable: 

1. Switch off your old Astro box.
2. To connect your Plug& Play Box via LAN cable:
   a) Remove the LAN cable from your old Astro box and connect the LAN cable to your new Plug & Play Box.
   i) For Maxis IPTV customers, keep the other end of the LAN cable connected to your router.
   ii) For TIME IPTV customers, go to the other end of the same LAN cable, plug it out from your modem, and into any LAN port on your router. Ensure that you’re not plugging your LAN cable back into the same box.
   ‍

Note: If you have a two-in-one modem & router, you can skip Step ii).  

To connect via Wi-Fi:

Remove your LAN cable from your old Astro box, and do not plug it into your new Plug & Play Box.

There will be no penalty imposed upon the removal of Astro GO+ from your subscription.

Refund  can be made when there be a termination of account, over payments and in  cases where payment was wrongly made to another Astro account.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the blue port in Cisco Router and direct to computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

‍

‍

4. Type the Username and Password as below. Then click "OK". (These are the defaults, if you have done previous configuration on your router the password may be different).

Username: admin

Password: admin (or time123)

5. Click "OK" when a Warning prompt that says,” Using this advanced utility to change your router settings could disable your network” appears. Below display will appears.

6. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

7. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

8. Click Wireless Security to view the security settings of your wireless network. Take note of the Security Mode and the Passphrase.

For the example below, the Security Mode used is WPA2/WPA Mixed Mode.

The Wireless name is called Network Name (SSID) and the Passphrase is your wireless password.

‍

9. Now that you have the Wireless name and Password, you are ready to connect your wireless computers and devices to the network.

10. You may change the Network Name (SSID) and the Passphrase to follow your preferences and please ensure save the changes made. Please reconnect to the new wireless name with the new password once completed.

‍

The WiFi SSID and password of the Mesh unit will be automatically synchronized to the WiFi router. Hence, there is no need to configure the WiFi parameters.

*WiFi SSID (Service Set Identifier) is the name of your wireless network, also known as Network ID. It is viewable to anyone with a wireless device within reachable distance of your network.

Please provide your primary mobile number via My Astro Portal, or send it to one of our platforms found here.

Note:

• Any changes of contact details to be requested by account holder only.
• Only account holder's contact to be updated as primary mobile number in the system.

STEP 1  

Check your current software version on your box.

If the software version updated (Refer to Table 1), proceed to STEP 2.

If software version different from Table 1, click here for Software Update guide.        

Once software is updated, tune to the impacted channel.        

If issue persist, proceed to STEP 2.

STEP 2    

Run Test Satellite Frequency.    

Click here for the guide.

If Test Pass, proceed to submit report here.

‍

Guide to  submit report:    

At Feedback Type select "I have  missing channel".    

Fill up all the required  information and submit.    

Please indicate if you agreed to recontract for 12 months (technical visit is FOC) or paid visitation  (RM65).    

You will receive appointment  details via SMS within 48 hours.

If Test Fail, proceed to STEP 3.

‍STEP 3    

Proceed to Update Satellite Frequency.    

Click here for the guide.    

Once completed, tune to the impacted channel.            

If issue persist, proceed to submit report here.

‍

Guide to  submit report:    

At Feedback Type select "I have  missing channel".    

Fill up all the required  information and submit.    

Please indicate if you agreed to recontract for 12 months (technical visit is FOC) or paid visitation  (RM65).    

You will receive appointment  details via SMS within 48 hours.

This initiative is part of Astro’s “GO GREEN” journey, which was implemented to promote paperless billing and to play our part in protecting the environment. The objective of the Paper Bill Charge is to encourage our customers to opt for e-Billing as their preferred Bill Delivery Method, which is also a more convenient and efficient way to access and manage their bills. Hence, a fixed RM10.00 monthly charge will be applied to all existing and new Astro customers who opt for Paper Bills as their preferred bill delivery method.

Yes, the monthly subscription fee will be prorated into your Astro bill.

There are no switching fees apply when existing Astro customer move to new packs.

To cancel your Multiroom (Smart TV) subscription, please call us at 03-9543 3838.

When using our One Time Payment (OTP) method, you may register more than one credit card per account. However, a single card account can only be used for a maximum of three accounts for OTP transactions.

When using our auto-debit facility, you can only register one card with Astro. Any subsequent card registrations will override the current one.

For more information about the Astro Fibre App, you may click here for a detailed user guide.

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required  screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info

A Ping Test shows how long it takes for packets to reach host.

A Traceroute Test traces the route of packets to destination host from our server.

Intermittent  internet connection using Wi-Fi

1. Router Positioning

Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.

i) High vs. Low

Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the  router of possible interferences.

ii) Concrete & Metals

Make sure your router isn't blocked by  any other objects, especially devices that are electronic. Also, avoid  placing your router in your basement as this area is usually enclosed by a  lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.

iii) Distance to Router

The further away from your router you  get, the weaker the Wi-Fi signal. Therefore, the best option is to place your  router as close to your devices as possible, but this is only practical if  you have one main area where you tend to use your devices.

Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put  it at one end of the house.

2.  Wireless Interference & Noise

You've probably never noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.

Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:

i) Microwaves

ii) Bluetooth Devices

iii) Cordless Phone

3.  Surrounding Wi-Fi signals

A truth of the modern world is that every  household has their own Wi-Fi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many routers within close proximity.

Which is why it's important that you pick a good channel in your  router settings. Modern routers can choose channels for you automatically,  but sometimes it's better to investigate and find the best channel yourself.

4. Usage

More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.

Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem  persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required  screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick  Info

A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.

A Ping Test shows how long it takes for packets to reach host.

A Traceroute Test traces the route of packets to destination host from our server.

STEP 1  

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3  

Navigate to Display and press "OK".

STEP 4    

Navigate to Resolution and press "OK".

STEP 5    

Navigate to your preferred selection and press “OK”.

STEP 6    

Select Yes, continue and press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

Astro Multiroom service mirrors all content from your primary subscription, except selected Special Interest and pay-per-view channels such as Astro First/Best movies.

For customers with Multiroom box, the Plug & Play setup with Astro Broadband will not have access to NHK World. The Plug & Play setup without Astro Broadband will not have access to NHK World.

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

Please visit any of Astro’s digital platform that you would like to log into, such as Astro’s official website (www.astro.com.my). Then, create a new Astro ID using your email address or mobile number by clicking “No Astro ID? Create Now!”. After creating your new Astro ID, please use it to log into our digital platforms moving forward.
 
If you have an active Astro subscription, you may also link it to your Astro ID. Please click here for the guide.
 

Yes, your charges during the deferment days will be pro-rated and reflected in your next bill. Please note that due to the recent requested change in your Astro account, the expiry date for your Disney+ Hotstar (3-months pass) subscription has been deferred to xxx (date) to consolidate the final monthly subscription pricing.

Yes, another person may register their credit card to your account's auto-debit facility. If you are performing this action via our call centre, the respective card holder is required to be present.

There are 2 methods of setting maturity ratings restriction on Netflix: 

‍

Method 1 – Create a Kids Profile in Netflix App on Ultra/Ulti Box 

1. On the Netflix home menu, select “Switch Profile” 

2. Select Add Profile.  

3. Name the profile. 

4. Select Kids. Kids profiles have a logo 'Kids' on the profile icon so they are easy to identify.  

5. Select Continue. The new profile will show on the list of profiles on your account. 

‍

Method 2 – Manually set Viewing Restrictions for each profile 

1. Go to https://www.netflix.com/profiles/manage

2. Select a Profile. 

3. Under Maturity Settings, select Edit. 

4. Enter your Netflix password. 

5. You may select the desired Maturity Rating settings or add a particular title restrictions for the profile. 

6. Select Save. 

For more information kindly visit: 

• https://help.netflix.com/en/node/114275

• https://help.netflix.com/en/node/114276

There is no contract for this subscription.

STEP 1
In the Kids Profile, press the Home button on your remote and the home menu will be displayed.



STEP 2
Navigate to Profile.



STEP 3
The Profile Selection Screen will be displayed.



STEP 4
Choose an Adult Profile.



STEP 5
Switching from a Kids to an Adult Profile will require you to enter a 4-digit PIN.
Please enter your PIN to proceed. If you have not set up your PIN, the default code is 0000.



STEP 6
After entering the PIN, you will be able to enter the Adult Profile.


 

SST of 6% and 8% will be applied accordingly to your bundle services:

1. 8% SST to Astro TV Pack
2. 6% SST to Astro Fibre

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Audio and press "OK".

STEP 4

Navigate to your preferred selection and press “OK”.

The promotion period of Astro Fibre’s Speed Upgrade Campaign is from 24 November 2023 until 31 May 2024.

You may visit any of Astro's digital platform that you would like to log into. Then, create a new Astro ID using your existing email address or mobile number. After creating your new Astro ID, please use it to log into our digital platforms moving forward.