For self-installation, in your first bill upon activation of your Plug& Play Box, the activation fee will be included as a separate line item in your bill alongside the subscription fee.

If you choose to install the Plug & Play Box via installer, you can pay the installation fee and activation fee directly to the installer upon installation. This will be reflected in your next bill itemised as setup fee.

The minimum recommended internet speed is 10 Mbps for HD videos and 30 Mbps for 4K UHD videos.

You will be able to watch almost immediately while the content streams through your Astro Box. Buffer time for the video to load will depend on the speed of your broadband.

Your average internet usage is shown as below:

STEP 1  

Press "HOME" button on your remote control.

STEP 2

Navigate to Update Satellite Frequency and press “OK”.

‍

STEP 3    

Choose Reprogramming and press “OK”.

STEP 4    

Select Yes, continue and press "OK" to proceed with the update.      

Otherwise, select No, go back to cancel.

STEP 5  

Satellite Frequency Update progress screen will be displayed.

‍

STEP 6    

The test result will be displayed once completed.    

Press "OK" to go back to  channel.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.
you may have to get your hands a little dirty.
 

1. Try loading the site on a different device.
   • Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.
   • If the website doesn't load on another device, the problem is either with the network or the website itself.
2. Restart your computer.
   • ​​Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.
3. Try loading the site in a different browser.
   • There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.
4. Temporarily disable your antivirus program.
   • Your antivirus software may be interfering with your ability to load certain websites.
   • Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.
5. Reset your modem and router.
   • Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.
6. Check your computer's date and time settings.
   • If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.
   • Check your computer or mobile device's clock to make sure that it is  set to the correct time and date.
7. In the event the problem persists, please provide below details for further escalation:
   • List of websites effected.
   • Run the Speed Test  via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.
   • Run the Traceroute Test - Please click here for Traceroute Test guideline.
   • Run the Ping Test -  Please click here for Ping Test guideline.
   • Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

To set up a Mesh WiFi network around your house, the Mesh unit will need to be paired with the WiFi router. Steps to pair these two devices are as follows:

i. Place the Mesh unit close to the WiFi router (within 2 meters) and power it on

ii. After the Mesh unit starts up, press and hold the WPS buttons of the Mesh unit and the WiFi router for 3 - 5 seconds in turn within 2 minutes

iii. After the WLAN and Internet indicators of the Mesh turns steady blue, the Mesh is connected to the Internet

iv. Move the Mesh to the desired place where you need to expand WiFi and power it on. After the Internet indicator turns steady blue, WiFi is expanded successfully.

Yes, a third party is allowed to make the advance payment on your behalf. In the case of refund, the amount will be returned to the owner of the third-party account (source of payment).

(i) Head over to My Astro Portal and go to 'Bill & Payment'. Click on 'Payment History'
(ii) Contact us via one of these platforms. Please ensure you include your Astro Account Number.

Connect your Ultra Box/Ulti Box today and get the full value for your subscription. We believe we can provide you the best entertainment experience in Malaysia, and it all starts with connecting your box to the internet.

Want to enjoy these features for free?

• Continue watching Astro even when it’s raining.
• Binge-watch and catch-up to 110,000 videos on-demand from Malaysia, Hollywood, Korea, China, Bollywood and more anytime.
• Create multiple profiles in your house to enjoy a personalized Astro experience, with shows recommended to you based on your interest. There is a Kids-friendly version for your little ones as well.
• Rewind, pause and fast-forward shows and matches so that you will never miss another moment.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Scroll to Network Settings and press "OK". Select New Wi-Fi Connection and press "OK".

‍

STEP 4

Select your Wi-Fi network and press "OK". Please enter the password to connect to your network.

STEP 5

You have successfully connected when this screen appears.

Please submit your issue here or you can WhatsApp us at 03-9543 3838.

You will not be able to switch between channels, use the app as a remote control, view favorite channels and programmes, use programme showtime reminder, and remote record feature.

Please switch your current subscriptions to our new Astro packs to subscribe to Multiroom (Smart TV). To sign up, WhatsApp "SWITCH" to 03-9543 3838 and an agent will assist you.

Find out more of our new packs at https://product.astro.com.my/tv

No, your rewards cannot be transferred to another person or exchanged for cash.

For Ultra/Ulti Plug & Play Box installation, it is recommended that you attempt to self-install by following the installation guide here, but there is an option to request for an installer to install the box at your premise. However, there will be a separate fee for this service request.

1. Unifi netis brand

The following shows an Interface based on Unifi router

1. Launch Web Browser and enter the default's gateway's IP address (192.168.1.1) in the address bar.

1. Enter Username and Password.
   1. Username = tmadmin
   2. Password = Adm@xxxx (xxxx refers to last four digits of MAC address)

1. Choose WLAN -> wlan0 (2.4GHz) Basic Setting. Note down on SSID.

1. Choose WLAN -> wlan1 (5GHz). Compare SSID with previous SSID.

1. If SSID for wlan0 (2.4GHz) and wlan1 (5GHz) are the same. Change wlan1 (5GHz) SSID by adding number 5(i.e. ifuni_5G) to differentiate from 2.4 GHz. Click Apply Changes.

Note: Connection to Wi-Fi may be temporarily loss while the changes is updated.

Astro subscribers will have the freedom to subscribe to Netflix via Astro, or they may also choose to continue subscribing via Netflix directly on their own.

Please refer to these FAQs for more information, or click here to learn more and sign up for the Ultra Box. Alternatively, you may call 03-7481 8000 to get in touch with an Astro representative.

Although it is possible to pair the second mesh node unit with the first mesh, customers are advised to follow similar steps in setting up the Mesh Network by pairing the mesh unit with the WiFi router instead.

The balance will be credited into your account, which will be reflected when you receive your next bill. The balance credit will be used to offset your bill balance.

Further details on pricing, billing and availability will be confirmed in coming months. Look out for more details and register your interest via https://astro.com.my/Netflix

If you have NOT made any changes to your Astro pack on or after 9th November 2021, you can enjoy up to four (4) concurrent streams on Astro GO anywhere, anytime. However, if you have Astro GO+ as part of your subscription, you will be upgraded to four (4) concurrent streams.

STEP 1
Switch off the power of your box and make sure that the adapter’s power light is off.


STEP 2
Unplug the HDMI cable from your TV and plug it back in securely to other available HDMI port.


STEP 3
Switch on the power for your box and make  sure that the adapter’s power light is on.
Please wait for 5 minutes.


STEP 4
Turn on your box. Do select the correct TV input.
You should no longer be experiencing this problem. 
​

To subscribe, WhatsApp "Smart TV' or call 03-9543 3838.

Astro customers on the previous packages (e.g. Family Pack, Starter Pack, Value Pack, Super Pack Lite, Super Pack or Super Pack Plus) will first have to sign up to our new packages on astro.com.my before they are able to sign up for Multiroom (Smart TV).

You can subscribe to Multiroom (Smart TV) here or via any of our sales channels.

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2  

Navigate to Settings.

STEP 3    

Navigate to Parental Control and press "OK".

STEP 4    

Please enter your PIN (Default PIN is 0000).

STEP 5    

Navigate to your preferred category to block and press "OK".

The new packs come with 200 hours of Cloud recording by default. If your current recordings exceed 200 hours, the system will delete the exceeded hours once your package has been changed, starting with the oldest recordings first.  

If you would like to retain the previous recordings which exceed 200 hours, you may opt for a selection of 400 or 1500 Cloud Recording hours at a chargeable rate of RM12 or RM15 per month (excl. govt tax) respectively. Or else, you may subscribe to the Platinum pack which comes with complimentary access to 1500 hours of Cloud Recording.

Please follow the steps below:

Step 1: Fill in Transfer of Equipment Ownership Form (Part A & Part B)

Step 2: Provide an Undertaking Letter if current account holder deceased or un-contactable. (Note: Copy of death certificate is required if account holder deceased).

Step 3: Provide a copy of new applicant NRIC for Malaysian or copy of passport for non-Malaysian or copy of IMM13 Pass with at least 6 months validity for Refugee. (Note: ASTRO name should be displayed on the top left corner on both sides of the identity card copy).

Step 4: A full payment to be made on any outstanding balance for all related accounts (if any).

Step 5: Submit all documents via feedback form .

Step 6: Customer will expect a call from our validation team (Note: Turnaround time for transfer of equipment ownership is 3-5 working days upon receiving all complete documentation).

Note:

1. There might be a loss of transmission during the processing of transfer equipment ownership, split or merge of equipment.

2. Recorded program will be removed for PVR user.

3. A full payment to be made on any outstanding balance for all related accounts.

4. New account holder agreed to continue the remaining contract from previous owner account (if any).

5. Auto debit will be voided upon acknowledgment of transfer equipment ownership (if any).

Additional requirement for New Owner

Capping of applicant age is 21

Malaysians aged < 26 years old and Non-Malaysian - requires copy of utility bill (Phone, Internet, Water or Electricity)

Unfortunately, this means that you are using a TV model that does not support 4K UHD resolution (Sony BRAVIA 4K GB, Sony BRAVIA 4K UR or Sony BRAVIA VH). Not to worry, we are working with the Sony team to ensure you will be able to enjoy these 4K UHD channels soon. We will keep you posted once these channels are available to you!

No, the quality of your video depends on the speed and reliability of your internet.

Tap on the "Account' screen on the navigation bar and scroll to the "Subscription' section. Tap on "TV Pack' to view your pack, box, multiroom, and Astro GO information.

While this technology has its benefits, different devices at home have different reaction and response to changes in signal strength and quality, and it's almost impossible to predict if they will make good band choices due to the interaction between the devices and the Wifi router. Some smart home devices also recommend that band steering is not used due to various reasons such as needing a constant consistent connection, ability to only connect to a particular band, registration of the respective MAC address, etc..

Example:

As single SSID is used, the device may remain on a weak 5GHz network  instead of switching over to stronger 2.4GHz network.

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required  screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info

A Ping Test shows how long it takes for packets to reach host.

A Traceroute Test traces the route of packets to destination host from our server.

Intermittent  internet connection using Wi-Fi

1. Router Positioning

Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.

i) High vs. Low

Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the  router of possible interferences.

ii) Concrete & Metals

Make sure your router isn't blocked by  any other objects, especially devices that are electronic. Also, avoid  placing your router in your basement as this area is usually enclosed by a  lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.

iii) Distance to Router

The further away from your router you  get, the weaker the Wi-Fi signal. Therefore, the best option is to place your  router as close to your devices as possible, but this is only practical if  you have one main area where you tend to use your devices.

Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put  it at one end of the house.

2.  Wireless Interference & Noise

You've probably never noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.

Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:

i) Microwaves

ii) Bluetooth Devices

iii) Cordless Phone

3.  Surrounding Wi-Fi signals

A truth of the modern world is that every  household has their own Wi-Fi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many routers within close proximity.

Which is why it's important that you pick a good channel in your  router settings. Modern routers can choose channels for you automatically,  but sometimes it's better to investigate and find the best channel yourself.

4. Usage

More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.

Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem  persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required  screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick  Info

A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.

A Ping Test shows how long it takes for packets to reach host.

A Traceroute Test traces the route of packets to destination host from our server.

Disney+ Hotstar is available on Chromecast (Gen 2 onwards, firmware 1.43 & above) and with the latest version of the Disney+ Hotstar app on iPhone, iPad and Android mobile. 

Follow these instructions to cast your film/series: 

• Make sure your mobile device and your Chromecast are on the same WiFi network 
• Log into your Disney+ Hotstar app 
• Select a film/series that you want to cast 
• Press "Play' 
• Once the film/series has started, tap on the casting icon 
• Select the screen you wish to cast to 
• The film/series should then be cast onto your screen

Multiroom (Astro Box) requires an Astro box to be setup and can be accessed through the regular satellite feed or streaming on home Wi-Fi. Meanwhile, the Multiroom (Smart TV) only requires a Smart TV and no installation needed. Customers can download the Astro app on the Smart TV and connect to home Wi-Fi to stream.

The matches will be available on the channels Astro Arena Bola (CH803) and Astro Arena Bola 2 (CH804), On Demand and Astro GO.

STEP 1  

Press "HOME" button on your remote control.

STEP 2    

Navigate to Preferences and press "OK".

STEP 3  

Navigate to Auto Standby and press "OK".

STEP 4    

Navigate to your preferred selection and press “OK”.

STEP 5  

Select Yes, continue and then press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

-The Mesh unit can only be used indoors. It can be mounted onto a wall or be placed horizontally on a desktop. Do not install it in other mode, such as on the ceiling.

-Keep a clearance of at least 10 cm around the device to ensure proper ventilation.

-Keep the device away from electrical appliances that generate strong magnetic or electric fields, such as microwave ovens.

There are a few ways you can access Netflix on the Ultra Box as below: 

• Access Netflix on the Ultra/Ulti Box via the Home Screen and select the Netflix app from the Apps row. 
• Launch the Netflix app directly from their remote control by clicking on the “Netflix” button if it’s available on your remote control. 
• Tune into CH 741

IMPORTANT! If you are accessing Netflix on your Ultra/Ulti Box for the first time, please wait for the Netflix activation email from Astro (this may take up to 10 minutes) for the app to be reflected in your account. If you skip this 10-minute period, you may experience double charging by incorrectly signing up for Netflix using your credit card details.

STEP 1    

On your remote, press the Home button and the home menu will  be displayed on top of your screen.

STEP 2

Navigate to Guide.

STEP 3    

Select the channel you would like to lock and press "OK".

STEP 4   

Select "Lock Channel" and press "OK".

STEP 5    

You channel is successfully locked when this screen appears.

STEP 6

Your selected channel will  have a lock tagging after being locked.

Astro customers can make payments via Auto-debit, WhatsApp,Astro Quick Pay and other authorised payment channels withoutsurcharge for the easiest and fastest way to pay their Astro bills.

‍Bill payments at selected petrolstations, convenience stores, retail/mobile shops, kiosks, and e-Wallets, may incur a surcharge of up to RM0.50 per transaction by the appointed collection agencies of RMS (Razer), ATX, MobilityOne and e-Pay.

The surcharge is imposed by third-party payment collection partners for services rendered.‍

You can refer to all our payment options below. Those marked with ‘*’ will be subject to a surcharge by appointed collection agencies.

‍

A. HASSLE-FREE METHODS

Auto-Debit:​
Click here for step-by-stepinstructions on how to activate auto-debit payment via My Astro Portal.‍


WhatsApp:

1. Save Astro’s WhatsApp number 03-9543 3838 into your contacts and send “Hi”to us via WhatsApp.
2. Follow the instructions in the menu to proceed with your payments.

JomPAY:​
Look for the JomPAY logo on your latest bill, log into your preferred online banking platform, and submit your payment details.
• Biller Code: 9639 (unique to Astro only)
• Ref-1: <10-digit Astro account number> (E.g. 08XXXXXXXX)


B. ASTRO SELF-SERVICE METHODS​

Astro Quick Pay​:

1. Visit pay.astro.com.my.
2. Just enter your 10-digit Astro Account Number and proceed with theinstructions that follow.

My Astro Portal​:

1. Login to My Astro Portal to conveniently make your payment online.
2. Select ‘PAY BILL’ and proceed with the instructions that follow.
3. You can also use this portal to check your billing and payment history.

Channel 200​:

1. Tune into CH200.
2. Select 'My Account'.
3. Click on 'Make Payment' and follow the instructions displayed on the screen.
4. SMS the code shown on your TV to 33777.
5. Wait for the SMS reply with an attached link to proceed with your payment.

My Astro App​:

1. Download My Astro app (available for FREE on both Google Play & Apple App Store).
2. Register/Login/Link account and provide a valid email address and mobile number.
3. Select 'My Account' on the menu bar to view your outstanding balance and click on 'Let’s Pay' to make your bill payments.
4. You will receive a push notification in your message inbox verifying that your payment has been made, upon successful payment.

C.BANKS​

Maybank:

• ATM
• Online banking

‍Visit maybank2u.com.my for more information.


Public Bank:

• ATM
• Cash Deposit Machine & Cheque Deposit
• Online banking

‍Visit pbebank.com for moreinformation.


Bank Simpanan Nasional:

• ATM
• Cash Deposit Machine
• Online banking
• SMS banking
• BSN Ejen Bank Berdaftar (EBB)
• Over-the-counter payments

‍Visit mybsn.com.my for more information.


Agrobank:

• ATM
• Online banking
• Over-the-counter payments

‍Visit agrobank.com.my for more information.
‍

D. e-WALLETS

A‍TX*
Boost, GoPayz, KelantanPay, Zcity (GEM REWARD), SabahPay, Tapay, GoPay,MerchantTradeMoney, ToneGroup, Elinking, Mpay, Mcash, and other various smaller wallets.

e-Pay*
Touch n Go (TnG), Grab Pay, Shopee, BigPay, True Money

‍E. OTHER METHODS​‍

‍Associated Retailers​:

RMS (Razer/ MOL)*
7-Eleven, 99 Speedmart, Caring Pharmacy

ATX*
RedONE Shop, Mobile Money, Runcit Hero (telecommunication shops), Parcel Hub (courier shops), Kiosk, DHL

Mobility One*
Kedai D’mart, Happy Mart, Pasaraya Sakan, PusatKomuniti Desa (PKD), Aeon Big and various sundry shops‍

e-Pay*
Petrol stations (Petronas, Shell, BHP, Caltex, Petron), KK Mart, Mydin, MyNews, SenHeng, Hai-O, Giant, TF ValueMart, Billion, Big Pharmacy

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.
 

1. Try loading the site on a different device.
   • Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.
   • If the website doesn't load on another device, the problem is either with the network
2. Restart your computer.
   • Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.
3. Try loading the site in a different browser.
   • There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.
4. Temporarily disable your antivirus program.
   • Your antivirus software may be interfering with your ability to load certain websites.
   • Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.
5. Reset  your modem and router.
   • Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.
6. Check your computer's date and time settings.
   • If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.
   • Check your computer or mobile device's clock to make sure that it is set to the correct time and date.

i. List of websites effected.
ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.  
iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.
iv. Run the Ping Test -  Please click here for Ping Test guideline.

Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.    
A Traceroute Test traces the route of packets to destination host from our  server.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Network Settings and press "OK".

STEP 4

Navigate to Network Diagnostics and press "OK".

STEP 5

Network Diagnostics screen will be  displayed accordingly.

You may use the same feedback form and choose below options.

Category: I would like to request for refund

Sub Category: Request for Refund

Yes, you may terminate the service, however an early cancellation fee will be applied for termination/cancellation within 24 months. Please refer to the Astro Fibre's cancellation details.

Yes, all existing Astro & Broadband customers within contract or out of contract can subscribe to Astro & Broadband offerings. The 24 months contract will be renewed upon signing up for the new packs.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

‍

STEP 2

Navigate to Settings.

STEP 3

Navigate to Menu Language and press "OK".

STEP 4

Navigate to your preferred language selection and press “OK”.