Yes, eKYC verification is mandatory. In addition, this verification process helps to reduce manual handling of customer's personal information and secure against unauthorised usage.

Please check your internet speed and connection status. If your internet is working without any issues, please logout & login into the app again.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.

You can subscribe to new packs via  

• Online - astro.com.my  
• WhatsApp GET ASTRO (for new customers) or SWITCH (for existing customers) to 03-9543 3838
• Astro Customer Service Centres.

There will be no penalty imposed upon the removal of Astro GO+ from your subscription.

You can proceed with below troubleshooting if the weather is good. Ortherwise, you may try again later.

STEP 1
On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.


STEP 2
Navigate to SETTINGS and press “OK”.


STEP 3
Navigate to STB DIAGNOSTICS and press “OK”.


STEP 4
Refer to the signal strength % shown on the top left of your screen.
If it is 65% or higher, please go to WhatsApp to receive further help.
If it is below 65%, please go to STEP 5.


STEP 5
Switch off the power for your box and make sure that the adapter’s power light is off.


STEP 6
Unscrew the satellite cable from the box and pull it out.


STEP 7
Plug the satellite cable back into the box and screw it back securely.


STEP 8
Switch on the power for your box and make sure that the adapter’s power light is on.
Please wait for 5 minutes.


STEP 9
Turn on your box. You should no longer be experiencing this issue.
If issue persist, please attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized Dish
 If issue persist under a centralised satellite dish, please refer to your respective Building Management before contacting our agents.

Step 1:
Type ASTRO<space>BAL<space>10-Digit Astro Account No. 
Example: ASTRO BAL 08XXXXXXXX

*Standard telco charges and Terms and Conditions apply

Step 2:
Send SMS to 66688

STEP 1
On your remote, press the Home button and the Home Page will be displayed on your screen.



STEP 2
Navigate to Profile.



STEP 3
The Profile Selection Screen will be displayed. 



STEP 4
Navigate to Edit Profile.



STEP 5
Choose a profile to edit.




STEP 6
Choose a new Profile Picture and press “OK”.


 

Mesh WiFi network refers to a unified wireless network that is formed by utilizing inter-connected WiFi nodes (Mesh devices) placed throughout the house.

By changing from a higher contract duration e.g., 24-months commitment period to lower contract duration e.g., 12-months, a proration of the cancellation fee will be applicable whereby you will be charged per contract's month balance against the maximum cancellation fee agreed upon during sign up for the offer.

A proration of the cancellation fee will be applicable whereby you will be charged per contract's month balance against the maximum cancellation fee agreed upon during sign up for the offer.

You will start a new contract with 12-months commitment and receive the corresponding discount for that duration.

Check out how a cancellation fee is calculated with examples via this link:

1. Please use a LAN ethernet cable and connect your computer/ laptop to the back of the Maxis Router.

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox, etc.

3. On the address bar, please go to http://192.168.1.254 and the page below will appear.

    The default login of the router as below. If you have done a configuration on your router and changed your password previously, please use the password you have previously set.
 

    Username: administrator

    Password: Router S/N (Available on the sticker at the back of the router)

4. Once you have successfully login, the router's web-based setup page will appear.

5. From the left menu, select WIRELESS to access the screen below.

6. You may change the Channel selection by scrolling down to the Advanced Setup.

7. To change the channel on 2.4 GHz and 5 GHz, click the drop-down arrow for Channel, then select your desired channel.

Then, click "Apply" for the changes to take  place.

8. A warning box will popup, click "OK" for the changes to take place.

9. Please wait until the connection reestablish.

No, you can remain in your current pack, however starting 9 November 2021, you would need to subscribe to the new packages to make any changes to your subscription. We strongly encourage customers to switch to the new packs to enjoy the best content experience from Astro.

Yes, the current service tax law does not exempt services provided to customers residing in Labuan, Langkawi, and Tioman.

For any NJOI-related information, please visit the NJOI Help & Support page at https://purchase.njoi.com.my/en-support

Service Tax will not be imposed on any CSR projects accounts. Any tax payable will be borne by Astro.

Yes, a third party is allowed to make the advance payment on your behalf. In the case of refund, the amount will be returned to the owner of the third-party account (source of payment).

If Netflix is included as part of your Astro pack, you will find it in My Astro app 

where you will be able to manage all the streaming apps you are entitled to.  

Netflix will also be included in your Astro bill under “Monthly Charges”  

If you have added Netflix to your bill (Netflix Add-on), the Netflix subscription charge will appear in your Astro bill under “One-time charges” as Netflix App Subscription or Netflix Premium and will be charged monthly. You should refer to Netflix account Management for any changes to your Netflix subscription or should you wish to change to other billing methods.

If you sign up Astro & Broadband with standard Ultra & Ulti box (DBB), all channels are available.  

However, there are channels that will not be available with Ultra/Ulti Plug & Play Box which are NHK World (398).

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.    

2. Ensure the fiber cable from your wall socket and modem is securely connected.

Notes: You might be connected to LAN 1 if backbone is Maxis

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 2/ Option 3/ Option 5/ Option 6

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.

2. Ensure the fiber cable from your wall socket and modem is securely connected.

3. Ensure both cables on the Modem (LAN Port 2) and Router (WAN Port - Red port) are properly connected.

Notes: You might be connected to LAN 1  if backbone is Maxis

Router connection

4. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

5. Please make sure both cables on Router (Any Yellow port) and Astro Decoder (Network Port behind decoder) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

7. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

1. Ensure power cable  is connected tightly.    

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

No, there will be no additional charges to access Liga Malaysia.

STEP 1

Switch off the power for your box and  make sure that the adapter's power light is off.

STEP 2

Locate the Smartcard at the front or right side and gently pull it out.

Make sure that the adapter's power light is off.

STEP 3

Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5

Switch on the power for your box and make  sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form and attach a picture of your smart card number for assistance.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your Ultra Box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

STEP 1

Check on your TV input to ensure correct input selected.

If issue remains, switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Unplug the HDMI cable from your box and plug it back in securely.

STEP 3

Switch on the power for your box and make sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 4

Turn on your box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form with the error details and provide  sim card number for assistance.

Yes, you may terminate the service. However, an early cancellation fee will be applied for terminations/cancellations within 24 months. Please refer to the Astro Fibre's cancellation details.

No, you will not be automatically switched to the new pricing. To perform a manual switch, please contact us at 03-9543 3838.

Yes, you can sign up for auto-debit after your account has been activated via My Astro.
 
Alternatively, you may also call our Customer Contact Centre at 03-9543 3838 for assistance or to enquire about any current Auto Debit promotions.

Advance payment can be made via credit/debit card or online banking.

No, there are no penalty fees for the Mesh WiFi devices should you wish to terminate Astro Fibre within/after 24 months. 

Step 1: Separate Your Wi-Fi Network Name

First, you need to set up your Wi-Fi to Dual-band in order to be less susceptible to interference, and allows you to choose between the 2.4GHz or 5GHz bands when connecting a device. A Wi-Fi frequency of 5GHz is best when you are near your router, and 2.4GHz is best for when you are far from your router.

• Check the bottom of your router for a website or IP address, username, and password.

Below are details for a standard login based on a standard router issued by ISP (Telekom Malaysia, Maxis, and Time dot Com)

• Login to your account
• Identify your Wi-fi Settings (This could be in advanced settings)
• Identify both the 2.4GHz and 5GHz options.
• Split the signals by renaming the 2.4GHz and 5GHz signals respectively, and make sure both are enabled.
• For detailed instructions based on router model, on how to separate your Wi-Fi, click here and choose the option according to your ISP and router brand.

Step 2: Factory reset your Ultra Box by following the steps below.

a. Press the Home button on your remote

b. Go to your settings page

c. Scroll down and select Reset/Restore

d. Select restore factory settings and proceed

e. Enter your PIN to access restore factory settings (default pin: 0000)

f. Choose restore and wait until the box reboots automatically. This may take around 2 minutes and you will see the Astro logo again when it's done.

For customers whose sign-up speed is 50Mbps, 100Mbps or 500Mbps, you will get to enjoy your upgraded speed of 100Mbps/500Mbps/800Mbps for 24 months.
 

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Navigate to IP Diagnostics and press "OK".

STEP 5    

IP Diagnostics information will be displayed.

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

For Residential Astro Pay TV customers: Yes, you are allowed to change your package to the one that best suits your entertainment needs. You may make the following pack changes:  

1. Pack upgrades

1. Movement within Entertainment, Movies or Sports (e.g., switching from Sports to Entertainment)

1. Movement within Premium pack (to a different combination of content)

For these changes, you will remain on same contract duration, or you can choose to change to longer commitment. If you downgrade your packs, you will be charged a cancellation fee for pack, and you can then choose a new contract for the new pack. Kindly note additional contract details for Disney+ Hotstar and Netflix.  

(Please refer to the section "Changes to your Astro Contract" for more details)

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

The new packs come with 200 hours of Cloud recording by default. If your current recordings exceed 200 hours, the system will delete the exceeded hours once your package has been changed, starting with the oldest recordings first.  

If you would like to retain the previous recordings which exceed 200 hours, you may opt for a selection of 400 or 1500 Cloud Recording hours at a chargeable rate of RM12 or RM15 per month (excl. govt tax) respectively. Or else, you may subscribe to the Platinum pack which comes with complimentary access to 1500 hours of Cloud Recording.

Step 1: You request for a move. 

‍
Step 2: One of our agents will contact you within 24 hours to set an appointment if you’re using Self Service - Astro Self-Service Portal.

‍
Step 3: You will receive a reminder of your appointment an hour before your scheduled time.

‍
Step 4: The technician will dismantle your satellite dish.

If there is no satellite dish, customers should dismantle the modem, router, and decoder by themselves.

‍
Step 5: You will need to transport your device(s) to your new home.

‍
Step 6: The technician will reinstall your satellite dish, (including modems and routers for broadband customers) at your new home based on the schedule appointment.

‍

Note For IPTV Customers:

1. Upon relocation request, all exiting IPTV customers will be converted to our Astro & Broadband service. Customers can choose to have standard Astro service with satellite dish, or unicast Plug & Play without satellite dish.

2. If customers choose to have satellite dish, an additional RM150.00 will be charged for satellite installation. If customers choose to have unicast Plug & Play service, no satellite dish is required, hence no extra charge will be incurred.

There are various offers currently available for both existing and new customers:

• Existing Astro TV Customers

You may choose from a selection of Astro Fibre speeds from 50Mbps to 800Mbps to accompany your Astro TV Packs from as low as RM60/month for 50Mbps or RM90/month for 100Mbps. That is more than RM900 of savings in total across all speed plans from 50Mbps to 800Mbps. On top of this offer, you will also get to enjoy a complimentary speed upgrade for 24 months if you subscribe within 24 November 2023 to 31 May 2024. This is part of Astro’s initiative to give better value to support loyal customers, and the full details of this offer are as follows:

*Offers applicable to non-Primary Pack bundles only.
**Speed upgrade offer is only eligible for customers who sign up within 24 November 2023 to 31 January 2024.
 

• For New Astro Customers

*Promotion price is applicable for Astro Fibre bundles only.
**Speed upgrade offer is only eligible for customers who sign up within 24 November 2023 to 31 May 2024.
 
 

Users can easily access all their streaming Apps such as Netflix, Disney+ Hotstar, Viu etc by clicking the “APPS” button on their remote control. After clicking this button, they will be brought to the Apps rail under the home page.

 

Connect your PVR to Wi-Fi and enjoy access to our library of Video On Demand. Replay old seasons, catch-up latest episodes of your favourite shows, anytime you want. To connect your PVR, follow the steps below depending on your box type:

(a) Wi-Fi Enabled PVR (DMT5)

·      Press the “Home” button and select “Settings” > “Network” > “Wi-Fi”

·      Allow the PVR to scan Wi-Fi networks available and subsequently choose your home Wi-Fi network > Enter your Wi-Fi password if required

·      Once connected, the icon below will appear on the screen.

‍
      Tip: Use the alpha-numeric keyboard on your Astro Remote to key in your password

·      Press the “Home” button and select “On Demand” to start watching videos on demand!

‍

(b) Non-Wi-Fi Enabled PVR (HD PVR)

There are two ways to connect your HD PVR decoder to your home Wi-Fi
(i) Using the Ethernet (LAN) cable 
 

·       Plug in the LAN cable from your modem into the PVR network port

·       Once connected, the icon below will appear on the screen

·       Press the “Home” button and select “On Demand” to start watching videos on demand!

(ii) Using an Astro Wi-Fi dongle as per shown below

Step 1 - Plugin the Wi-Fi dongle into the front USB part of your PVR decoder.

Step 2 - A prompt will appear stating "Do you wish to connect to a wireless network?", select "Yes, continue."

Step 3 - Once connected, the Wi-Fi icon will appear on the screen. Now you are ready to download and enjoy Astro's on demand entertainment.

Step 4 - Press the “Home” button and select “On Demand” to start watching videos on demand!

*The Wi-Fi dongle is only applicable for the non-Wi-Fi enabled PVR (as per the picture).

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2    

Navigate to Guide.

STEP 3  

Select the channel you would  like to add to favourite list and press "OK".

STEP 4  

Select "Add to Favourites" and press "OK".

STEP 5

You are successfully added the channel to favourite list when this screen appears.

STEP 6

Your selected channel will have a heart tagging after added as favourite.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the blue port in Cisco Router and direct to computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

‍

‍

4. Type the Username and Password as below. Then click "OK". (These are the defaults, if you have done previous configuration on your router the password may be different).

Username: admin

Password: admin (or time123)

5. Click "OK" when a Warning prompt that says,” Using this advanced utility to change your router settings could disable your network” appears. Below display will appears.

6. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

7. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

8. Click Wireless Security to view the security settings of your wireless network. Take note of the Security Mode and the Passphrase.

For the example below, the Security Mode used is WPA2/WPA Mixed Mode.

The Wireless name is called Network Name (SSID) and the Passphrase is your wireless password.

‍

9. Now that you have the Wireless name and Password, you are ready to connect your wireless computers and devices to the network.

10. You may change the Network Name (SSID) and the Passphrase to follow your preferences and please ensure save the changes made. Please reconnect to the new wireless name with the new password once completed.

‍

You can be assured that your data are safe with us. Astro implemented sufficient security measures to protect customer data and fully comply to Personal Data  Protection Act

There will be no installation fee for both Astro Box and Ultra Box. The Multiroom (second decoder) must be installed at the same registered address as your primary subscription.

You may proceed with the following troubleshooting steps and it shouldn't take you much longer than 15 min

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Yellow port at Tplink Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to tplinkwifi.net and to access to below login page. Type the Username and  Password, then click "Login".

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your  router previously, the password may be different.

For example, below is the login details of the above router:
 

Username: admin

Password: TIMECE24
 

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, choose Advanced and click the Wireless tab on the left menu. Then, select Wireless Settings from the sub menu. Below screen will appear for 2.4GHz selection.

i. Please ensure to tick Enable Wireless Radio function.

ii. To change the channel, click the  drop-down arrow for Channel, then select your desired channel.

Choose between 1 to 13 (Suggested  channels : 1,6,11). Then, click "Save" for the changes to take place.

iii. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

iv. Next, select 5GHz to make changes on the wireless channel for 5GHz.

v. Click the drop-down arrow for Channel, then select your desired channel from the selection.

vi. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

Yes, you may upgrade to the Ultra Box if you are currently on the Entertainment or Movie Pack. If you are on the 500Mbps or 800Mbps plan, the upgrade will be free. However, a one-time fee of RM100 (excluding Govt. Tax) will apply if you are on the 50Mbps or 100Mbps plan. Please call or WhatsApp our Customer Contact Centre at 03-9543 3838 if you would like to make this upgrade. Please refer to the table below for the complete guide for Ultra Box upgrade:

If you choose to downgrade your packs or terminate Astro services before the end of your contract term, you will have to pay a cancellation fee. This cancellation fee is calculated based on your subscribed package, contract period and box type. If you cancel your service(s)/change your packages upon completion of your contract term, you won't have to pay any cancellation fee.

Astro is an official distributor of Disney+ Hotstar, the dedicated streaming home for global, and Malaysian hits. Astro customers can now subscribe to Disney+ Hotstar through the new, bigger and more diverse Packs, i.e.: Movies, Premium 1, Premium 3 or Platinum Pack. The streaming service brings together blockbuster movies from Hollywood to Hallyu and award-winning content from Disney, Marvel, Star Wars, Pixar, National Geographic, FX, 20th Centuary Studios and more including exclusive premieres from leading Malaysian studios. Take your family entertainment to the next level with Disney+ Originals like I am Groot, Prey, Baymax, Obi-Wan Kenobi, She-Hulk, IN THE SOOP: Friendcation and more - with the convenience of one monthly bill for all your entertainment needs. 

Movies Pack, Premium 1, Premium 3 and Platinum customers as well as customers on the Starter Plus Pack, Value Plus Pack, and Disney+ Hotstar (3-months Pass) can enjoy Disney+ Hotstar on Astro. 

Customers can subscribe to Disney+ Hotstar via astro.com.my/Disney, as well as via authorised retailers and dealers. 

My Astro is available on web browser and app. The app can be downloaded for free from the Google Play Store, Apple App Store or Huawei App Gallery.

For Ultra and/or Ulti box users, My Astro app is now added to the Top Menu so you can easily access it to manage or update your account. You may find it in the Top Menu, located next to Settings. Please refer to the image below to see what it looks like: