BYOND / PVR / Ultra Box

To dismantle ONLY - FOC
‍
To reinstall ONLY – RM65
‍
To dismantle and reinstall - RM65

‍

Broadband / IPTV

Relocation within 6 months of contract start will be charged a RM500.00 relocation fee, and the contract will be renewed to a new 24-month contract.

Relocation after 6 months of contract start will have their contract renewed to a new 24-month contract.

‍

Note For IPTV Customers: 

1. Upon relocation request, all exiting IPTV customers will be converted to our Astro & Broadband service. Customers can choose to have standard Astro service with satellite dish, or unicast Plug & Play without satellite dish.

2. If customers choose to have satellite dish, an additional RM150.00 will be charged for satellite installation. If customers choose to have unicast Plug & Play service, no satellite dish is required, hence no extra charge will be incurred.

‍

‍

*Please note that additional charges may apply if the reinstallation process requires extra cables/fixings.

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please ensure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Intermittent internet connection using Wi-Fi

1. Router Positioning
   Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
   
    i) High vs. Low
   Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   
   ii) Concrete & Metals
   Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   
   iii) Distance to Router
   The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
   
   Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.
   
    

2. Wireless Interference & Noise
   You've probably never noticed but there are wireless signals all around you wherever you go and they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.
   
   Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:
   i) Microwaves
   ii) Bluetooth Devices
   iii) Cordless Phone
    

3.  Surrounding Wi-Fi signals
   A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel  overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many  routers within close proximity. Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

4. Usage
   More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

Mac OS X

1. Click the Go tab in the top menu bar and select Utilities from the drop-down menu.

2. Type "network utility" in the search bar in the top right-hand corner of the Utilities window and then hit the "Enter" key on your keyboard. 

3. Click the Network Utility icon to open the Network Utility window.

4. For Ping Test, select the Ping tab and then type the address you'd like to ping in the text box. Click Ping and wait for the ping results.
 

5. For Traceroute Test, select the Traceroute tab and then type the address you like to traceroute in the text box. Click Trace and wait for the traceroute results.
 

Windows 10

1. Click the Search icon (magnifying glass) in the bottom left-hand corner and type "cmd" into the search bar.

2. Select the Command Prompt app - it will be at the top of the list of search results as the best match.

3. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

Windows 7 & Vista

1. Open the Start menu by clicking the Windows icon at the bottom left-hand corner of the screen.

2. Type "cmd" in the search bar at the  bottom of the menu.

3. Click cmd found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows 8

1. Move the mouse to the right-hand corner of the screen to make the vertical menu bar (charm bar) appear. Click Search.

2. Type "cmd" in the search bar and hit the Enter key on your keyboard.

3. Click cmd that found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows XP

1. Click the Start button in the bottom left-hand corner of the screen.

2. Click the Run option in the right-hand column.

3. Type "cmd" in the text box and then hit the Enter key on your keyboard.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you'd like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

Astro & Broadband comes with 24-month contract commitment.

Please refer below for the installation and activation fees for Astro customers on the new pack.

Currently, this change affects SMS bills only. Other SMSs such as (but not limited to) bill reminders, payment notifications, promotional SMSs or technical appointment reminders will still be sent to you if applicable.

STEP 1
Please wait while your Astro box initializes.



STEP 2
Select your preferred language.



STEP 3
Navigate to Next and press "OK".



STEP 4
Select Auto as the Video Resolution.



STEP 5
Navigate to Next and press "OK".



STEP 6
Navigate to Confirm and press "OK" to confirm your selection if you are able to read the texts on screen properly.
Otherwise, navigate to Cancel to revert to the previous settings.



STEP 7
Select IPTV Plug & Play (self-install) as the box operating mode.



STEP 8
Navigate to Next and press "OK".



STEP 9
Select your preferred connection.
For connection via Wi-Fi, proceed to STEP 10.
For connection via LAN Cable, proceed to STEP 16 once you are connected.



STEP 10
Please wait while your Astro box searches for available Wi-Fi networks.



STEP 11
Navigate to your preferred Wi-Fi network and press "OK".



STEP 12
Please enter the password to connect to the Wi-Fi network.



STEP 13
Navigate to Done to continue.



STEP 14
Please wait while your Astro box connects to the internet.



STEP 15
Navigate to Yes to allow your Astro box to connect to this network automatically.
Otherwise, navigate to No.
Proceed to STEP 17 for the next step.



STEP 16
Navigate to Next and press "OK". 



STEP 17
Your box's connection status will be displayed.
Navigate to Finish to complete the setup.

Yes, you can. Go to the Account tab and scroll to "Subscription' section. Select "TV pack', select "Main room' or "Multiroom' and then click the "Refresh' button.

Yes, existing Astro customers can subscribe to all Astro & Broadband offerings. 24 months contract will be renewed upon signing up for broadband.

Yes, you can switch to Astro Fibre and all the devices provisioned will be maintained (Fibre modem & WiFi router) with the new Astro Fibre subscription. However, your Astro TV package will be removed/terminated.

An early cancellation fee will be applied if you are still within the 24-month contract. Please refer to the Astro Fibre's cancellation details.

The speeds shown under “My Network Map” are the WiFi speeds of your connected devices based on factors such as signal strength, distance of devices from your router, obstructing objects etc. This function allows users to know the signal strengths achievable from every room in their house or any distance from their router, giving users accurate indication If additional mesh is needed or if the placement of their router requires adjustment.

However, the speeds shown under “My Devices” are the recent WiFi consumption of your connected devices, which allows you to monitor every user’s internet consumption in your household.

No there will not be any penalty.

For the Multiroom subscription on a box setup, if your subscription is within the 24-month contractual period. Then a pro-rated penalty of RM600 will be applied for any Astro box except for Ultra Box, which the penalty will be RM1,000.

Call our contact centre 03-9543 3838 or visit us at astro.com.my.

You may register up to four (4) devices.

To remove devices on Astro GO, click on Settings > Registered Devices to view and remove a device(s) from the list of devices registered to your Astro ID.

Your purchase will be reflected on your next monthly Astro bill. For example, if you rented a movie for RM 15.00 for 2 days and your next bill statement is in 2 weeks. RM 15.00 will be reflected in your Astro subscription bill in two weeks' time.

Please upgrade the Ultra/Ulti Box software to enjoy Netflix on your Ultra/Ulti Box. To do this, please click on the Netflix app icon on the homepage or go to CH741 to prompt the software upgrade. Kindly click Install when the software upgrade prompt appears. This will take approximately 20 minutes and you would be able to launch Netflix on the Ultra/Ulti Box after that.

Multiroom (Astro Box) requires an Astro box to be setup and can be accessed through the regular satellite feed or streaming on home Wi-Fi. Meanwhile, the Multiroom (Smart TV) only requires a Smart TV and no installation needed. Customers can download the Astro app on the Smart TV and connect to home Wi-Fi to stream.

Your account number will be used to identify/verify you for all After Sales-Services. You may also use your mobile number/ Astro smart card number/ NRIC number or Astro Box number.

Mesh WiFi network refers to a unified wireless network that is formed by utilizing inter-connected WiFi nodes (Mesh devices) placed throughout the house.

To cancel your Multiroom (Smart TV) subscription, please call us at 03-9543 3838.

The default PIN is 0000. You may change your PIN to a secure one by doing this at Settings, under your Preferences, select PIN Management, enter your old PIN or default PIN and proceed to create a new PIN.

To reconnect your Astro account, please check your Account status, Bill Summary and pay on Astro Quick Pay. Your disconnected services will resume within 1 hour after you have paid your "Total Overdue Charges"

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

From General Tab, take a look at the Current Entry Point Name for the LNB type of your input source.

You can proceed with below BTS if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to Diagnostics and press “OK”.

STEP 5

Refer to the signal strength on your screen.

If it is 65 or higher, please take the screenshot and submit your feedback form.

If it is below 65, please go to Step 6.

STEP 6

Switch off the power for your box and  make sure that the adapter’s power light is off.

STEP 7

Unscrew the satellite cable from the box  and pull it out.

STEP 8

Plug the satellite cable back into the  box and screw it back securely.

STEP 9

Switch on the power for your box and make sure that the adapter’s power light is on. Please wait for 5 minutes.

STEP 10

Turn on your box. You should no longer be experiencing this issue.

If issue persist, please submit the issue on our Feedback Form with error details and attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized  Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

Connect your PVR to Wi-Fi and enjoy access to our library of Video On Demand. Replay old seasons, catch-up latest episodes of your favourite shows, anytime you want. To connect your PVR, follow the steps below depending on your box type:

(a) Wi-Fi Enabled PVR (DMT5)

·      Press the “Home” button and select “Settings” > “Network” > “Wi-Fi”

·      Allow the PVR to scan Wi-Fi networks available and subsequently choose your home Wi-Fi network > Enter your Wi-Fi password if required

·      Once connected, the icon below will appear on the screen.

‍
      Tip: Use the alpha-numeric keyboard on your Astro Remote to key in your password

·      Press the “Home” button and select “On Demand” to start watching videos on demand!

‍

(b) Non-Wi-Fi Enabled PVR (HD PVR)

There are two ways to connect your HD PVR decoder to your home Wi-Fi
(i) Using the Ethernet (LAN) cable 
 

·       Plug in the LAN cable from your modem into the PVR network port

·       Once connected, the icon below will appear on the screen

·       Press the “Home” button and select “On Demand” to start watching videos on demand!

(ii) Using an Astro Wi-Fi dongle as per shown below

Step 1 - Plugin the Wi-Fi dongle into the front USB part of your PVR decoder.

Step 2 - A prompt will appear stating "Do you wish to connect to a wireless network?", select "Yes, continue."

Step 3 - Once connected, the Wi-Fi icon will appear on the screen. Now you are ready to download and enjoy Astro's on demand entertainment.

Step 4 - Press the “Home” button and select “On Demand” to start watching videos on demand!

*The Wi-Fi dongle is only applicable for the non-Wi-Fi enabled PVR (as per the picture).

If you sign up for Maxis 30/100/300Mbps broadband speeds, you are not entitled for the complimentary mesh WiFi devices. However, you may walk into any Maxis Retail Stores to purchase the mesh WiFi devices.

Depending on your service, it is mandatory to return some devices as per our T&Cs, whilst other devices should be disposed of and recycled at collection centres registered under the Department of Environment. To find out what you should do with your devices after service termination, please click here.

STEP 1    

Switch OFF the power of your Ultra / Ulti box and make sure that the adapter's power light is off.

STEP 2    

Switch ON the power of your Ultra / Ulti box and make sure that the adapter's power light is on.

‍

STEP 3  

Put the box on standby mode.

STEP 4

Press and hold the Home button on the box.

STEP 5    

Wait until "boot" appear on the front panel and released.

STEP 6

When “boot” appears, press “Standby”,  “Left “, “Up” continuously until Auto Update appear on box screen and Software Update progress on TV.

‍

‍

STEP 1    

Switch OFF the power of your box and make sure that the adapter's power light is off.

‍

STEP 2

Switch ON the power of your box and make sure that the adapter's power light is on.

STEP 3

Press Standby, Ch+, Standby keys on the box simultaneously when the "boot" message appears on the box front  panel.

The Software Update progress screen will appears.    

The update will take 10 - 15 minutes to complete. Please be patience.

STEP 1  

Switch OFF the power of your box and make sure that the adapter's power light is off.

STEP 2    

Switch ON the power of your box and make sure that the adapter's power light is on.

STEP 3

Press the standby button repeatedly after switch on the power.

STEP 4

Press "OK".

STEP 5    

The Software Update progress screen will appears.

The update will take 10 - 15 minutes to complete.

Please be patience.

My Astro app and web is currently available in English and Bahasa Malaysia only.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the Smartcard at the front or right side and gently pull it out make sure that the adapter's power light is off.

STEP 3

Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be  experiencing this problem.

If issue persist, please submit your feedback form with error details and attach a picture of your sim card number for assistance.

No, the courier charges are borne by Astro for the retrieval of the box and Smart Card/SIM Card.

There will be two attempts made to retrieve the box and you are required to be available at the agreed upon time.

When you have reached the duration (years) needed for the upgrade, we will upgrade you into your new tier and your shiny new rewards will appear in the My Astro app. You are still eligible for all the rewards from previous tiers too.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your Ultra Box. You should no longer be experiencing this problem.

If issue persist, please submit the issue in our Feedback Form with the error details and provide sim card number for assistance.

Your account may be under suspension. To resolve this issue, proceed to submit report via WhatsApp or Feedback Form.

The promotion period of Astro Fibre’s Speed Upgrade Campaign is from 24 November 2023 until 31 May 2024.
 

This change was made to ensure that all customers enjoy a better user experience on our platforms and are kept up to date with which email address and mobile number is linked to their account.

Disney+ Hotstar is available on Chromecast (Gen 2 onwards, firmware 1.43 & above) and with the latest version of the Disney+ Hotstar app on iPhone, iPad and Android mobile. 

Follow these instructions to cast your film/series: 

• Make sure your mobile device and your Chromecast are on the same WiFi network 
• Log into your Disney+ Hotstar app 
• Select a film/series that you want to cast 
• Press "Play' 
• Once the film/series has started, tap on the casting icon 
• Select the screen you wish to cast to 
• The film/series should then be cast onto your screen

Option 1

1. Please turn off  all devices (Modem and Router). By restarting your modem, you can isolate the  possibility of overloaded processes in the modem, which would impact its  performance.
2. Ensure both cables on Modem (LAN Port  1) and Router (Internet Port) are properly connected.
    

Modem connection

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - LAN port) to PC/ Laptop.

4. If you have change the password in Selfcare Time portal recently,  please change the router configuration follows the new password made in Selfcare, but if you didn't make any changes, please go to Step 5.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option 2/ Option 3

1. Please turn off all devices (Modem and  Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.
2. Gently remove fiber optic cable and blow / wipe the tip of the fiber cable. This is to clean up the cable in order to avoid any interferences.
3. Re-insert the fiber cable to the optical port behind the modem.
4. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem Connection

Router Connection

5. Make Sure both cables on Modem (LAN Port 4/ LAN Port 3 for second decoder) and Astro Decoder (Network Port) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.


Option 5

1. Please ensure LAN cable is directly connected to modem port LAN 1.

2. Please use different LAN port if LAN 1 port is still off / not working.

3. If the issue persists, submit your feedback form for further assistance.