1. Please standby  computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.254 and below page  will appear.

If below box appear, please enter required details:

USERNAME: Administrator

PASSWORD: (ACCESS KEY AT THE RGW STICKER)

(These are the defaults, if you have done previous configuration on your router the password may be different)

4. Once enter into the page "'TECHNICOLOR TG784N V3'', you may follow below steps to get the best wireless channel information.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. In order to get the best wireless channel, click "Wireless Scan" to scan available surroundings wireless Channel.

D. Please choose channel with lesser number of usage.

Example in below case, you may choose channel 4.

5. To configure wireless channel, please proceed with below steps.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. Then, click "Configure" to change the channel selection (automatic to manual) and other configuration option.

D. Please ensure below items:

i. WLAN Enable: Tick

ii. Interface Enable: Tick

iii. Change the Channel Selection to Manual

iv. Change the wireless Channel based on Step 4(D).

v. Once completed the selection, click the "Apply" button.

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

The promotion period of Astro Fibre’s Speed Upgrade Campaign is from 24 November 2023 until 31 May 2024.
 

STEP 1    

Switch on the power for your box and make sure that the adapter's power light is on.

STEP 2    

Put the box on standby mode.

STEP 3    

Press and hold the Home button on the box.

STEP 4    

Wait until "boot" appear on the front panel and released.

STEP 5    

New Installation Settings page will appear.    

Click here for the guides to complete the setup.

STEP 1    

Switch off the power of your box and ensure the adapter�s power light is off.

STEP 2    

Switch on the power of your box and ensure the adapter�s power light is on.

STEP 3    

Press and hold the Ch+ and Ch- keys on the box simultaneously when the "boot" message appears on the front panel.

STEP 4    

Wait until the "Clr" message appears on the front panel, then release the Ch+ and Ch- keys.

STEP 5    

New Installation Settings page will appear.    

Click here for the guides to complete the setup.

STEP 1    

Ensure your box is on standby mode. (Red light on box's front panel).

STEP 2    

Press and hold the Standby button. Wait until the LED at front panel change from red to green for 3 times, then release the button.

STEP 3    

New Installation Settings page will appear.    

Click here for the guides to complete the setup.

STEP 1    

Switch off the power of your box and ensure that the adapter�s power light is off.

STEP 2    

Switch on the power of your box and ensure that the adapter's power light is on.

STEP 3    

Keep pressing the 'Power' button until the Startup Option screen appears.

STEP 4    

Press "369" on the remote control to trigger refresh box setting menu.

STEP 5    

Press "OK" to proceed. The box will be refreshed to the original setting.

STEP 6    

New Installation Settings page will appear.    

Click here for the guides to complete the setup.

To check your contract, please visit My Astro.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Preferences and press "OK".

STEP 3  

Navigate to Language and press "OK".

STEP 4    

Choose your language preferences and press "OK".

STEP 5  

Select Yes, continue and press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

The all-new Astro Fibre is Astro's own internet service whereby customers would be able to enjoy the Astro content over the internet via wireless connection along with high-speed internet service ranging from 50Mbps - 800Mbps.

While Astro & Broadband offers Astro content in partnership with Maxis Fibre Broadband or Allo City Broadband for customers to enjoy the best entertainment through Astro while staying connected with high-speed internet.

No, the Astro Fibre App is a free mobile application for all Astro Fibre customers with the latest RG21 router.

All streaming apps willbe made available on the Ultra Box first, followed by the Ulti Box. If youwould like to upgrade to the Ultra Box, please visit product.astro.com.my/tv or reach us via WhatsApp by typing “Hi” at 03-9543 3838 forassistance.

For customers who wish to have their physical tax invoices reprinted, there will be a flat fee of RM10.00 levied as part of the process which has been implemented since year 2015.

STEP 1  

Press "HOME" button on your remote control.

STEP 2

Navigate to Update Satellite Frequency and press “OK”.

‍

STEP 3    

Choose Reprogramming and press “OK”.

STEP 4    

Select Yes, continue and press "OK" to proceed with the update.      

Otherwise, select No, go back to cancel.

STEP 5  

Satellite Frequency Update progress screen will be displayed.

‍

STEP 6    

The test result will be displayed once completed.    

Press "OK" to go back to  channel.

To continue enjoying your PVR decoder and service, you must maintain a minimum monthly subscription fee of RM60 (not inclusive of the recording fee and Govt. Tax).

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/ laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/ laptop].
2. You may open any web browser such as  Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)

Username: admin
Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the  configuration.

i. On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab.

ii. Please ensure Wireless RF Mode is Enabled.

iii. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

iv. Click Submit. Router will auto reboot and connection re-establish after few minutes.

Starting 23 August 2022, Astro customers will progressively be able to access Disney+ Hotstar via the Ulti Box, in addition to the Ultra Box, mobile app and website. 

Please follow the steps below:

Step1: Fill in Merge/Split Equipment Form (Part A & Part B)

Step2: A full payment to be made on any outstanding balance for all related accounts (if any).

Step3: Submit all documents via feedback form or walk in to nearest Astro Customer Service Centre (CSC).

Step4: Customer will expect a call from our validation team (Note: Turnaround time for merge/ split of account is 3-5 working days upon receiving all complete documentation).

Note:

1. There might be a loss of transmission during the processing of transfer equipment ownership, split or merge of equipment.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.
 

1. Try loading the site on a different device.
   • Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.
   • If the website doesn't load on another device, the problem is either with the network
2. Restart your computer.
   • Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.
3. Try loading the site in a different browser.
   • There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.
4. Temporarily disable your antivirus program.
   • Your antivirus software may be interfering with your ability to load certain websites.
   • Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.
5. Reset  your modem and router.
   • Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.
6. Check your computer's date and time settings.
   • If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.
   • Check your computer or mobile device's clock to make sure that it is set to the correct time and date.

i. List of websites effected.
ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.  
iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.
iv. Run the Ping Test -  Please click here for Ping Test guideline.

Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.    
A Traceroute Test traces the route of packets to destination host from our  server.

Please refer to these FAQs for more information, or click here to learn more and sign up for the Ultra Box. Alternatively, you may call 03-7481 8000 to get in touch with an Astro representative.

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.
2. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem connection

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - LAN  port) to PC/Laptop.

4. If you have change the password in Selfcare Time portal recently, please change the router configuration follows the new password made in  Selfcare, but if you didn't make any changes, please go to Step 5.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 2 / Option 3

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.

2. Gently remove fiber optic cable and  blow / wipe the tip of the fibre cable. This is to clean up the cable in  order to avoid any interferences.

3. Re-insert the fiber cable to the  optical port behind the modem.

4. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem Connection

Router Connection

5.  Make Sure both cables on Modem (LAN Port 4 /LAN Port 3 for second decoder) and Astro Decoder (Network Port) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after  reboot.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.


Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/ power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

Option 5

1. Please ensure LAN cable is directly connected to modem port LAN 1.

2. Please use different LAN port if LAN 1 port is still off / not working.

3. If the issue persists, submit your feedback form for further assistance.

Of course! Please ensure your account is active when requesting for a move.

Unfortunately, your Disney+ Hotstar access with Astro will be terminated as well. 

Real-time payments are posted almost instantaneously. However, daily system maintenance occurs between 12AM to 3AM - any payment made during this period will be delayed until system maintenance is complete.

If you are interested to upgrade your box, you can do so via Astro's retailers or online as follows:

I. Visit https://hub.astro.com.my/#5

II. Select `Box Upgrade` and log in with your Astro ID

III. Select the box you would like to upgrade

Once you have received the eKYC link, you need to complete the verification within 3 days.

1. Router Positioning
   • Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
   • High vs. Low
     • Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals
     • ​Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for WiFi signals to penetrate.
   • Distance to Router
     • ​ The further away from your router you  get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
     • Otherwise, you should place your  router near the center of your home. After all, WiFi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.
2. Wireless Interference & Noise
   • You've probably never  noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices,  WiFi routers, satellites, cell towers, and more.
   • Although WiFi is  supposed to be on a different frequency than most of these devices, the  amount of radio noise can still cause interference. Some common causes of interference include:
     1. Microwaves
     2. Bluetooth Devices
     3. Cordless Phone
3. Surrounding Wi-Fi signals
   • A truth of the modern world is that every  household has their own WiFi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many  routers within close proximity.
   • Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels  for you automatically, but sometimes it's better to investigate and find the best channel yourself.
4. Usage
   • More likely, however, is that the people  on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/ Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

To request for a move, you may choose to:

1. Self-serve by logging in to My Astro app and follow the steps below:

Step 1: From Account tab, choose Installation address under Subscription.
Step 2: Click "Relocate”.
Step 3: Verify your identity via OTP.
Step 3: Fill in the OTP that you receive and proceed by clicking "Verify"
Step 4: Confirm the Address, a support ticket will be created.

2. Submit your feedback via below link: https://support.astro.com.my/feedback-form

Step1: Choose Feedback Type

• Type: Technical issues
• Issue: I want to enquire about installation/ relocation

Step2: Fill in the form and click “Submit” support ticket.

The main changes are the revamped look and feel of the user interface on the Smart TV App, which include redesigns to the Astro interface that consists of title rows at the Home Page to feature popular franchises, new live programmes posters and changes to the menu bar for easier navigation.

For more info, please read our dedicated FAQ on this here.

In addition, we have also recently introduced a new look to the Title Information Page and the ability to disable the Profile Selection Screen. For more information, please click here.

Yes, Mesh WiFi add-on is available for both Astro Fibre Bundle and Astro Fibre subscription.

Yes, customers who have upgraded their packages or reconnected their Astro service in February 2024 will be charged with 8% Service Tax from 1st March 2024, for services period on or after 1st March 2024.
 

Slow browsing using LAN cable

Looks like there is something wrong with your service connection.

Please run the Speed Test and attach the picture or screenshot of the speed test in the Feedback Form below, in order for us to provide further assistances.

Click here for Speed Test guideline.

Quick Info

A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
 

Slow browsing using Wi-Fi

1. Router Positioning

Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
 

i) High vs. Low

Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
 

ii) Concrete & Metals

Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
 

iii) Distance to Router

The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
 

Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.

2. Wireless Interference & Noise

You've probably never noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.

Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can  still cause interference. Some common causes of interference include:

i) Microwaves

ii) Bluetooth Devices

iii) Cordless Phone

3. Surrounding Wi-Fi signals

A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel  overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many routers within close proximity.

Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

 

4. Usage

More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/ Netflix.

Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.


Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

You will need to have an Astro subscription before you can subscribe to Disney+ Hotstar as an add-on service via Astro or enjoy any Astro bundle promotions. Please click here to subscribe to our Movies, Premium 1, Premium 3 or Platinum Pack to enjoy all your favourite Global and Malaysian hits for even better value and savings!

There are various offers currently available for both existing and new customers:

• Existing Astro TV Customers

You may choose from a selection of Astro Fibre speeds from 50Mbps to 800Mbps to accompany your Astro TV Packs from as low as RM60/month for 50Mbps or RM90/month for 100Mbps. That is more than RM900 of savings in total across all speed plans from 50Mbps to 800Mbps. On top of this offer, you will also get to enjoy a complimentary speed upgrade for 24 months if you subscribe within 24 November 2023 to 31 May 2024. This is part of Astro’s initiative to give better value to support loyal customers, and the full details of this offer are as follows:

*Offers applicable to non-Primary Pack bundles only.
**Speed upgrade offer is only eligible for customers who sign up within 24 November 2023 to 31 January 2024.
 

• For New Astro Customers

*Promotion price is applicable for Astro Fibre bundles only.
**Speed upgrade offer is only eligible for customers who sign up within 24 November 2023 to 31 May 2024.
 
 

Astro is an official distributor of Disney+ Hotstar, the dedicated streaming home of global, and Malaysian Hits. Astro customers can now subscribe to Disney+ Hotstar through our Movies, Premium 1, Premium 3 or Platinum Pack and enjoy award-winning entertainment with Disney+ Hotstar alongside Astro's much-loved local content for even better value and savings. Now, customers can enjoy Disney+ Hotstar on their Ultra or Ulti Box, mobile app or web! In addition, customers who have multiple primary Astro accounts will be entitled to multiple entitlements to Disney+ Hotstar.

Tap on the "Account' screen on the navigation bar and scroll to the "Subscription' section. Tap on "TV Pack' to view your pack, box, multiroom, and Astro GO information.

You will need to bring along all devices to your new place as no new devices will be issued.

Relocation will be subjected to new 24 months recontract and standard relocation fee applies for both Maxis and Allo respectively.

Please submit your issue here or you can WhatsApp us at 03-9543 3838.

1. Please standby computer/laptop to access to the internet and connection must be via LAN  (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and  direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.1.254 and below page will appear.

The default login of the router as below. If you have done a configuration on your router previously,  the password may be different.

Username: user
Password: Router S/N (Available on the sticker at the back of the router)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the left menu, choose Wireless 2.4GHz  and then click Basic Settings tab on the left menu to access to below screen.

6. You may change the Wireless Network Name (SSID) and the SSID Password to follow your preferences, then click "Save"  for the changes to take place.

Please reconnect to the new wireless name with the new password once completed.

7. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

You may change the Wireless Network Name (SSID) and the SSID Password to follow your preferences for 5GHz by choosing Wireless 5GHz  then click Basic Settings.

Click "Save" for the changes to take  place and reconnect to the new wireless name with the new password once  completed.

Visit https://product.astro.com.my/box or check out our user guide for a quick and easy way to get started!

No, Astro & Broadband with Maxis/Allo comes in bundle packages only.

Standalone broadband subscription is only applicable to our Astro Fibre service.

STEP 1    

Check your current software version on your box.

If the software version updated (Refer to Table 1) , proceed to STEP 2.

If software version different from Table 1, click here for Software Update guide.

Once software is updated, tune to the impacted channel.        

If issue persist, proceed to STEP 2.

‍

STEP 2  

Run Test Satellite Frequency.    

Click here for the guide.

‍

If dCSS Scan Entrypoint Success, proceed to submit report here.

Guide to submit report:    

At Feedback Type select "I have Astro service related question/request" and Sub Category as "Technical Interruption".

Fill up all the required information and submit.    

Please indicate if you agreed  to recontract for 12 months (technical visit is FOC) or paid visitation (RM65).    

You will receive appointment details via SMS within 48 hours.

If dCSS Scan Entrypoint Fail, proceed to STEP 3.

‍

‍STEP 3    

Proceed to Update Satellite Frequency.

Click here for the guide.
Once completed, tune to the impacted channel.

If issue persist, proceed to submit report here.

‍

Guide to submit report:    

At Feedback Type select "I have Astro service related question/request" and Sub Category as "Technical Interruption".

Fill up all the required information and submit.    

Please indicate if you agreed to recontract for 12 months (technical visit is FOC) or paid visitation (RM65).    

You will receive appointment details via SMS within 48 hours.

We would need you to  run few tests in order for us to understand your issue and to assist you in fixing the problem.

You may proceed with the troubleshooting steps below which should not require any longer than 15 minutes.

1. Please run each of the tests according to your your Laptop/PC Software.
2. Compile the pictures / screenshots of your test results in one file (i.e Microsof Word document, PDF file) and attach them in the Support Ticket below in order for us to assist you further:
   • List of websites effected.
   • Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.
   • Run the Traceroute Test - Please click here for Traceroute Test guideline.          
   • Run the Ping Test - Please click here for Ping Test guideline.
3. Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.

A Ping Test shows how long it takes for packets to reach host.

A Traceroute Test traces the route of packets to destination host from our server.