Upon submitting your application, you will receive the eKYC link via SMS/email/astro.com.my to complete the eKYC verification within 3 days.

No, there is no penalty or switching fee if you decide to cancel your Multiroom (Smart TV) subscription.

Your Disney+ Hotstar will be paused and will only resume once your Astro service is reinstated. 

Yes, as long as it is compatible with Open Mesh standards and Astro Fibre equipment. However, Astro will not be responsible for managing or configuring the device. For the optimum WiFi experience, please pair your Astro Fibre with Astro's Mesh WiFi.

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

You do not need to request for a reconnection as our system will detect your payment and process it immediately, provided you paid via a real-time payment channel.

Click here for a full list of our payment channels.

Mac OS X

1. Click the Go tab in the top menu bar and select Utilities from the drop-down menu.

2. Type "network utility" in the search bar in the top right-hand corner of the Utilities window and then hit the "Enter" key on your keyboard. 

3. Click the Network Utility icon to open the Network Utility window.

4. For Ping Test, select the Ping tab and then type the address you'd like to ping in the text box. Click Ping and wait for the ping results.
 

5. For Traceroute Test, select the Traceroute tab and then type the address you like to traceroute in the text box. Click Trace and wait for the traceroute results.
 

Windows 10

1. Click the Search icon (magnifying glass) in the bottom left-hand corner and type "cmd" into the search bar.

2. Select the Command Prompt app - it will be at the top of the list of search results as the best match.

3. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

Windows 7 & Vista

1. Open the Start menu by clicking the Windows icon at the bottom left-hand corner of the screen.

2. Type "cmd" in the search bar at the  bottom of the menu.

3. Click cmd found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows 8

1. Move the mouse to the right-hand corner of the screen to make the vertical menu bar (charm bar) appear. Click Search.

2. Type "cmd" in the search bar and hit the Enter key on your keyboard.

3. Click cmd that found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows XP

1. Click the Start button in the bottom left-hand corner of the screen.

2. Click the Run option in the right-hand column.

3. Type "cmd" in the text box and then hit the Enter key on your keyboard.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you'd like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

No, eligible customers will not be charged for this speed upgrade. Your speed plan will be upgraded automatically for 24 months, depending on your subscription. After the FREE speed upgrade period, your Astro Fibre plan will return to its regular speed.
 

Your access to Astro GO will depend on the subscription pack that you are subscribed to. Not all shows/channels will be available on Astro GO as this depends on contractual rights with specific guidelines on the entitlement of these shows/channels. We are continuously working hard to make more content available on Astro GO.

You may navigate around the menu on the side bar on Astro GO app, or top bar on the Astro GO web version to find shows available.

Menu Guide

• Home: Check out all the recommended content or watch your subscribed TV channels via the   Channel Guide at the bottom of your home screen. 
• Catch Up: Missed an episode of your favourite series? Fret not, Catch Up on the latest episode of your favourite shows on Astro GO. 
• Boxsets: Watch complete seasons and series from our On Demand library anytime anywhere. 
• Movies: Watch recent and popular movies on your devices! You can access a large catalogue of On Demand movies, according to your subscription. 
• Kids: Catch all the cartoons, animations and a variety of shows for kids of all ages. 
• Sports: Watch the biggest sporting shows LIVE on your mobile device, anytime anywhere. 
• Store: Other than your subscribed packages, you can also purchase and watch your favourite Pay-Per-View movies and other Astro exclusive content (not available on iOS devices).

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/ laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/ laptop].
2. You may open any web browser such as  Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)

Username: admin
Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the  configuration.

i. On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab.

ii. Please ensure Wireless RF Mode is Enabled.

iii. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

iv. Click Submit. Router will auto reboot and connection re-establish after few minutes.

Customers with a Netflix Premium account are allowed to watch on up to 4 supported devices in 4K UHD and Netflix Spatial Audio. In addition, Netflix Premium subscribers are also allowed to download shows to watch offline on 6 devices at a time.

STEP 1
On your remote, press the Home button and the Home Page will be displayed your screen. 



STEP 2
Navigate to SETTINGS.



STEP 3
Navigate to Profile Selection on Startup and press “OK”.



STEP 4
Navigate to your preferred selection and press “OK”.



STEP 5
Navigate to Save and press “OK”.

STEP 1  

Press "HOME" button on your remote control.

STEP 2

Navigate to Update Satellite Frequency and press “OK”.

‍

STEP 3    

Choose Reprogramming and press “OK”.

STEP 4    

Select Yes, continue and press "OK" to proceed with the update.      

Otherwise, select No, go back to cancel.

STEP 5  

Satellite Frequency Update progress screen will be displayed.

‍

STEP 6    

The test result will be displayed once completed.    

Press "OK" to go back to  channel.

For all new Astro Fibre customers with the RG21 router, the Astro Fibre App will be installed on your mobile device for you during installation. Alternatively,you may refer to the user guide here for self-installation.

Yes, from now till 31 May 2022, new customers who sign up for the Platinum Pack on a 24-month contract get to enjoy 60 days on Astro including complimentary access to Sports Extra for 24 months.

For further details on Platinum Pack, please click bit.ly/PlatinumPack60DaysOnUs. Alternatively, new customers on the Movies Pack can enjoy 30 days access to the pack on us.

For more details, please click bit.ly/MoviesPack30DaysOnUs.

If you subscribe to Astro Fibre between 1 October 2023 to 23 November 2023, you may still get the speed boost by calling in to our Customer Contact Centre at 03-9543 3838 and re-contracting with us. Kindly note that your account will restart with a new 24-month contract.

If you have forgotten your username or password, you may follow the steps below:

Step 1. Go to netflix.com

Step 2: Click on Sign In

Step 3: Click on "Need Help

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.
2. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem connection

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - LAN  port) to PC/Laptop.

4. If you have change the password in Selfcare Time portal recently, please change the router configuration follows the new password made in  Selfcare, but if you didn't make any changes, please go to Step 5.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 2 / Option 3

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.

2. Gently remove fiber optic cable and  blow / wipe the tip of the fibre cable. This is to clean up the cable in  order to avoid any interferences.

3. Re-insert the fiber cable to the  optical port behind the modem.

4. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem Connection

Router Connection

5.  Make Sure both cables on Modem (LAN Port 4 /LAN Port 3 for second decoder) and Astro Decoder (Network Port) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after  reboot.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.


Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/ power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

Option 5

1. Please ensure LAN cable is directly connected to modem port LAN 1.

2. Please use different LAN port if LAN 1 port is still off / not working.

3. If the issue persists, submit your feedback form for further assistance.

For My Astro App Users 
Go to the "Account' tab and scroll to "Personal Info' section. Click "Name & contact info' to view and update your personal contact information.

For Ultra and/or Ulti Users 

1. Launch the My Astro app on your Home screen and you will land on your My Astro account dashboard. Then, press the yellow button on your Astro remote control to visit your "Account details".
2. Press the down button to view the "Personal info".
3. Press the left button and focus on the edit icon for the contact details, press on "OK" to change your contact details.

Advance payment can be made via credit/debit card or online banking.

Please provide your primary mobile number via My Astro Portal, or send it to one of our platforms found here.

Note:

• Any changes of contact details to be requested by account holder only.
• Only account holder's contact to be updated as primary mobile number in the system.

No, Astro & Broadband only offers a 24-month contract period upon sign up.

Step 1:
Type ASTRO<space>BAL<space>10-Digit Astro Account No. 
Example: ASTRO BAL 08XXXXXXXX

*Standard telco charges and Terms and Conditions apply

Step 2:
Send SMS to 66688

 Activate your Disney+ Hotstar access with your Astro subscription, using the steps below:

• Step 1 - Create- and verify your Astro ID at astro.com.my/astroID. If you already have an existing Astro ID, go to Step 2.

• Step 2 - Goto astro.com.my/Disney. Login with your Astro ID, activate with your mobile number and verify with a one time passcode (OTP) sent to your mobile number.

• Step 3 - Download the Disney+ Hotstar app or login via web, and sign in with the mobile number provided in Step 2. Start streaming!

• Bundle Packs with Chinese Favourites: If you are currently on the Chinese Favourites selection, your selection will switch to Viu Premium at no additional cost progressively from 1 April 2024. Not to worry, you may still manually switch to other Asian Favourite selections if you wish via the My Astro app.

• Chinese Favourites Add-ons: There will not be any changes to your current subscription pricing. Furthermore, your subscription will now include additional channels on a free preview basis.

• Old Packs: There will not be any changes to your current subscription pricing. However, as we have recently made adjustments to the channel lineup in our packs, please call us at 03-7481 1000 (Monday to Friday, 9AM – 6PM exclude public holidays) to find out how you get more value from your subscription.

You may proceed with the following troubleshooting steps and it shouldn't take you much longer than 15 min

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Yellow port at Tplink Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to tplinkwifi.net and to access to below login page. Type the Username and  Password, then click "Login".

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your  router previously, the password may be different.

For example, below is the login details of the above router:
 

Username: admin

Password: TIMECE24
 

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, choose Advanced and click the Wireless tab on the left menu. Then, select Wireless Settings from the sub menu. Below screen will appear for 2.4GHz selection.

i. Please ensure to tick Enable Wireless Radio function.

ii. To change the channel, click the  drop-down arrow for Channel, then select your desired channel.

Choose between 1 to 13 (Suggested  channels : 1,6,11). Then, click "Save" for the changes to take place.

iii. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

iv. Next, select 5GHz to make changes on the wireless channel for 5GHz.

v. Click the drop-down arrow for Channel, then select your desired channel from the selection.

vi. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

No, this change in due date will not impact your monthly bill subscription.

If you choose to self-install the Plug& Play Box, then no installation fee will be charged. However, there will be an activation fee (please refer to the table below)

If you choose to have an installer to install the Plug & Play Box, then an installation fee will also apply.

If you have NOT made any changes to your Astro pack on or after 9th November 2021, you can enjoy up to four (4) concurrent streams on Astro GO anywhere, anytime. However, if you have Astro GO+ as part of your subscription, you will be upgraded to four (4) concurrent streams.

If your account is suspended or disconnected, you will retain the existing subscription when you reconnect. However, if you plan to make any changes after the reconnection, you can only select from the new packs.

Astro Rewards is open to all *Active Astro PayTV customers and their immediate family members

* "Active Astro customer" refers to subscriber of the Astro Service and whose account is current and active with no outstanding payments due and owing to Astro and who has not breached the Astro subscription agreement nor given any instructions to terminate and /or suspend his/her subscription to the Astro Service as at the date of winner notification. Winners must remain active Astro customers until the date of collection of prizes.

You can subscribe to new packs via  

• Online - astro.com.my  
• WhatsApp GET ASTRO (for new customers) or SWITCH (for existing customers) to 03-9543 3838
• Astro Customer Service Centres.

1) Download the Astro app from the app store available on your Smart TV.

2) Follow the steps below depending on your Smart TV brand.

There are a few ways you can access Netflix on the Ultra Box as below: 

• Access Netflix on the Ultra/Ulti Box via the Home Screen and select the Netflix app from the Apps row. 
• Launch the Netflix app directly from their remote control by clicking on the “Netflix” button if it’s available on your remote control. 
• Tune into CH 741

IMPORTANT! If you are accessing Netflix on your Ultra/Ulti Box for the first time, please wait for the Netflix activation email from Astro (this may take up to 10 minutes) for the app to be reflected in your account. If you skip this 10-minute period, you may experience double charging by incorrectly signing up for Netflix using your credit card details.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.        

‍

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Black port at D-Link Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.    

3. On the address bar, please go to http://dlinkrouter.local./ and below page will appear. (These are the defaults and if you have done a configuration on your router previously, the password may be different).          

Username: admin          

Password: (Leave the field blank)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, click Settings and then choose Wireless.

6. Below screen will appear to configure the wireless setting. Since this is a dual band router, you will have 2 Wi-Fi Names (SSID) i.e. 2.4GHz and 5GHz.

You may connect to any of the SSID, preferably with a stronger signal available.

7. You may change the Wi-Fi Name (SSID) and the Password to follow your preferences, and then click "Save" for the changes to take  place.

Please reconnect to the new wireless name with the new password once completed.

If band steering is enabled, you do not need to worry about which frequency band that your devices are connected to because the WiFi router will make the assessment and direct each device to appropriate frequency band.

However, it is important to note that quality and signal strength are not guaranteed due to unpredictability given that it is completely up to the connected devices and the WiFi router to intelligently decide on which band to connect.