You can proceed with below BTS if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to Diagnostics and press “OK”.

STEP 5

Refer to the signal strength on your screen.

If it is 65 or higher, please take the screenshot and submit your feedback form.

If it is below 65, please go to Step 6.

STEP 6

Switch off the power for your box and  make sure that the adapter’s power light is off.

STEP 7

Unscrew the satellite cable from the box  and pull it out.

STEP 8

Plug the satellite cable back into the  box and screw it back securely.

STEP 9

Switch on the power for your box and make sure that the adapter’s power light is on. Please wait for 5 minutes.

STEP 10

Turn on your box. You should no longer be experiencing this issue.

If issue persist, please submit the issue on our Feedback Form with error details and attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized  Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

Tap on the "Account' tab on the navigation bar and scroll to "Billing' section. Tap on "Bill Statement' to view any bill statement up to six (6) months.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the  site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.

1. Try loading the site on a different device.

Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.

If the website doesn't load on another  device, the problem is either with the network or the website itself.
 

2. Restart your computer.

Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.
 

3. Try loading the site in a different browser.
 

There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can  load the website.
 

4. Temporarily disable your antivirus program.

Your antivirus software may be interfering with your ability to load certain websites.

Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.
 

5. Reset your modem and router.

Traffic to or from a certain website may be getting tripped up by your  modem or router. Resetting these devices may allow you to access the website again.
 

6. Check your computer's date and time settings.

If your date or time is set incorrectly, you may not be able to  connect to secure (https://) websites.

Check your computer or mobile device's clock to make sure that it is  set to the correct time and date.
 

7. In the event the problem persists, please provide below details for further escalation:

   i. List of websites effected.

   ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.

   iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.

   iv. Run the Ping Test -  Please click here for Ping Test guideline.

Once you've  gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

Refund can only be made by the registered Astro account holders.

However, if you would like to request refunds on behalf of the account holder, you may do so by providing the supporting documents (e.g.: authorization  letter, death certificate, 3rd party NRIC copy).

Astro sends regular payment reminders to customers via SMS until their current charges have been paid. However, we encourage customers to pay their bill as soon as possible to avoid disconnection of Astro service. Please reach out to us here if you require more information about payment reminders or to change your contact details.

The minimum internet speed required to stream via Ultra Plug & Play Box is 30Mbps for 4K UHD viewing, and Ultra/Ulti Plug & Play is 10Mbps for HD viewing. For better streaming experience, we recommend 100Mbps and above.

Please follow the steps in Q5, then continue with the steps below:

You may use the 'forgot password' recovery feature on the login page. Just enter the email address/ mobile number you signed up with and we will send you a recovery email.  

If your account is suspended or disconnected, you will retain the existing subscription when you reconnect. However, if you plan to make any changes after the reconnection, you can only select from the new packs.

No, please use a Malaysian mobile number registered with a local network service to register and activate access for Disney+ Hotstar with your Astro subscription. 

To access these streaming apps, you would need to upgrade to the Ultra or Ulti Box by visiting product.astro.com.my/box. Alternatively, you may also reachus via WhatsApp by typing "Hi

STEP 1  

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3  

Navigate to Display and press "OK".

STEP 4    

Navigate to Resolution and press "OK".

STEP 5    

Navigate to your preferred selection and press “OK”.

STEP 6    

Select Yes, continue and press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

No, the Astro Fibre App is available for Astro Fibre customers with the RG21 router only.

The fee is a one-time activation fee that will be charged when you subscribe to the Plug & Play Box.

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please ensure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Intermittent internet connection using Wi-Fi
1. Router Positioning

Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day  and night.

  i) High vs. Low

     Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.

  ii) Concrete & Metals

      Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also,       avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which       can be almost impossible for Wi-Fi signals to penetrate.

  iii) Distance to Router

      The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.

Otherwise, you should place your  router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.

2. Wireless Interference & Noise

You've probably never  noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices,  Wi-Fi routers, satellites, cell towers, and more.

Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:

i) Microwaves
ii) Bluetooth Devices
iii) Cordless Phone

3.  Surrounding Wi-Fi signals

A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially  problematic in housing complexes and apartments where there can be many routers within close proximity.

Which is why it's important that you pick  a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

4. Usage

More likely, however, is that the people  on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/ Netflix.

Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in  your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document,  PDF, Image file) before submitting the form.

Quick Info
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

STEP 1

Check on your TV input to ensure correct input selected.

If issue remains, switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Unplug the HDMI cable from your box and plug it back in securely.

STEP 3

Switch on the power for your box and make sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 4

Turn on your box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form with the error details and provide  sim card number for assistance.

All Astro customers who are actively using their username to log in will be notified via email or SMS two (2) weeks before this change takes place. Please refer to the guide below on how to check for your registered contact details:

Astro does not provide installment plan facilities. You are advised to pay your charges before the due date, as per your monthly bill statement.

My Astro app and web is currently available in English and Bahasa Malaysia only.

If you subscribe to Astro Fibre between 1 October 2023 to 23 November 2023, you may still get the speed boost by calling in to our Customer Contact Centre at 03-9543 3838 and re-contracting with us. Kindly note that your account will restart with a new 24-month contract.

Please switch your current subscriptions to our new Astro packs to subscribe to Multiroom (Smart TV). To sign up, WhatsApp “SWITCH” to 03-9543 3838 and an agent will assist you. 

Find out more of our new packs at https://product.astro.com.my/tv

Of course not! It is a value-added service introduced for your convenience.

The Multi-user Profile feature allows customers to create individual profiles within their Astro Box and Astro GO with the following personalisations:

• Personalised Recommendations
• Continue Watching 
• Watch List
• Last Viewed Channel
• Favourite & Blocked Channels

The MUP feature is a great way to allow individual users to tailor personal Astro experiences whilst using a shared device (e.g.: Astro Box) in the household, providing them with better personalised recommendations and encouraging better content discovery.

Click here to find out more on this new feature and how to use it!

If you accidently clicked “delete my account” on the Astro Fibre app, you will bedirected to submit a request via Feedback Form as the image below.

If you submit a request, our Astro representative will get back to you within 3 business days to learn more about the issue(s) you are currently facing with the app. Customers may proceed to permanently delete their account during the call if they wish. Once complete, your Astro ID will be deleted and you will be unlinked from all Astro apps and services including partner apps that are associated with your Astro ID including Astro GO, My Astro, Astro Awani, Syok, beIN SPORTS CONNECT, iQIYI, TVBAnywhere+,HBO GO, Gempak, XUAN, Astro Ulagam etc.

You may create another Astro ID by following the steps here and re-link your new account to all Astro apps and services, including partner apps.

This error indicates that you are streaming on Astro GO while being connected to a VPN. Please close your VPN application and try streaming again.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.

Starting 1 April 2024, Astro’s Chinese content offering on our Primary & Family Pack is now bigger than ever with the addition of up to 10 channels featuring the latest Chinese primetime dramas, variety and current affairs programmes as well as great selection of movies and musical shows. These are the channels available in the Primary & Family Pack at no additional cost:

• Celestial Movies (CH309)
• TVB Jade (CH310)
• Astro AOD (CH311)
• TVB Entertainment News (CH317)
• TVB Xing He (CH319)
• TVBS Asia (CH320)
• NHK World (CH398)

No. Starting 1 April 2024, for new customers and current customers looking to switch their Asian Favourites, our Asian Favourites options will be:

• Viu Premium
• Indonesian Favourites
• Indian Favourites

Yes, existing Astro & Broadband customers within contract or out of contract can subscribe to Astro Fibre Bundle. The 24-month contract will be renewed.

However, your contract with Maxis/Allo needs to be terminated before signing up to this offer. An early cancellation fee applies if you are still within contract.

‍*Subject to Terms &Conditions of your contract

All streaming apps willbe made available on the Ultra Box first, followed by the Ulti Box. If youwould like to upgrade to the Ultra Box, please visit product.astro.com.my/tv or reach us via WhatsApp by typing “Hi” at 03-9543 3838 forassistance.

Starting 1 April, access to TVBAnywhere+ is no longer available to Astro customers. However, you can continue to enjoy TVB content via On Demand and TVB Jade (CH310) and Astro AOD (CH311). If you would like to subscribe to the TVBAnywhere+ app, you may still do so by purchasing it directly from TVB.

Yes, you can. If you are an existing Astro customer with the Disney+ Hotstar add-on option, your Disney+ Hotstar add-on option will be converted without any early termination charge upon your successful re-contract to eligible bundle packages. 

Want to return your Ultra or Ulti Plug & Play Box? It's simple and free!

Here's what you can do with your unused Ultra/Ulti Plug & Play Box:

1. Return your device to us via Arranged Pick-up:

Step 1: Please call Astro's Contact Centre at 03-9543 3838 to schedule an arranged pick-up by one of our courier partners.

Step 2: Just sit back and relax! A courier agent will come to your doorstep to retrieve the devices.

1. Please use a LAN ethernet cable and connect your computer/ laptop to the back of the Maxis Router.

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox, etc.

3. On the address bar, please go to http://192.168.1.254 and the page below will appear.

    The default login of the router as below. If you have done a configuration on your router and changed your password previously, please use the password you have previously set.
 

    Username: administrator

    Password: Router S/N (Available on the sticker at the back of the router)

4. Once you have successfully login, the router's web-based setup page will appear.

5. From the left menu, select WIRELESS to access the screen below.

6. You may change the Channel selection by scrolling down to the Advanced Setup.

7. To change the channel on 2.4 GHz and 5 GHz, click the drop-down arrow for Channel, then select your desired channel.

Then, click "Apply" for the changes to take  place.

8. A warning box will popup, click "OK" for the changes to take place.

9. Please wait until the connection reestablish.

Yes, customers will be charged a fixed Paper Bill Fee of RM10.00 per bill every month for each account.

Payment for Astro services will not increase. However, the Service Tax applicable will be increased from 6% to 8% and this will result in an increase in the total amount payable.

Service Tax is charged based on the date the service is rendered. For services rendered on or after 1st March 2024, the Service Tax rate would be at 8% whilst for services enjoyed before 1st March 2024, the Service Tax rate would be 6%.
 

A deposit of RM500 is payable for new subscribers (non-Malaysians). The fee will be refunded when service is terminated.

No deposit is required for all existing Astro customers and new subscribers (Malaysians).

Rebates/refunds are not provided. Early termination of the 3-months pass add on is subject to an early termination fee prorated to RM54.90 for the remaining months.

1. Tune to Astro channel 200 - select "Add-Ons"

2. Select the option for Monthly Subscription

3. Send the WhatsApp code as per displayed on the TV screen

No additional subscription is required. Video On-Demand (VOD) is a value-added service for all Astrro customers with connected Astro boxes (Ultra Box, Ulti Box, HD-PVR & PVR boxes). All you have to do is connect your decoder to your home Wi-Fi and you'll be able to access the world of on demand. Binge-watch, rewind, fast-froward and stream all your favourite shows anytime.