You can proceed with below BTS if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to Diagnostics and press “OK”.

STEP 5

Refer to the signal strength on your screen.

If it is 65 or higher, please take the screenshot and submit your feedback form.

If it is below 65, please go to Step 6.

STEP 6

Switch off the power for your box and  make sure that the adapter’s power light is off.

STEP 7

Unscrew the satellite cable from the box  and pull it out.

STEP 8

Plug the satellite cable back into the  box and screw it back securely.

STEP 9

Switch on the power for your box and make sure that the adapter’s power light is on. Please wait for 5 minutes.

STEP 10

Turn on your box. You should no longer be experiencing this issue.

If issue persist, please submit the issue on our Feedback Form with error details and attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized  Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

In general, these two bands can be differentiated with these parameters: Coverage, Channel Interference and Speed.

2.4GHz gives better coverage but lower speeds, while 5GHz provides faster internet but covers a smaller area.

STEP 1    

Check your current software version on your box.

If the software version updated (Refer to Table 1) , proceed to STEP 2.

If software version different from Table 1, click here for Software Update guide.

Once software is updated, tune to the impacted channel.        

If issue persist, proceed to STEP 2.

‍

STEP 2  

Run Test Satellite Frequency.    

Click here for the guide.

‍

If dCSS Scan Entrypoint Success, proceed to submit report here.

Guide to submit report:    

At Feedback Type select "I have Astro service related question/request" and Sub Category as "Technical Interruption".

Fill up all the required information and submit.    

Please indicate if you agreed  to recontract for 12 months (technical visit is FOC) or paid visitation (RM65).    

You will receive appointment details via SMS within 48 hours.

If dCSS Scan Entrypoint Fail, proceed to STEP 3.

‍

‍STEP 3    

Proceed to Update Satellite Frequency.

Click here for the guide.
Once completed, tune to the impacted channel.

If issue persist, proceed to submit report here.

‍

Guide to submit report:    

At Feedback Type select "I have Astro service related question/request" and Sub Category as "Technical Interruption".

Fill up all the required information and submit.    

Please indicate if you agreed to recontract for 12 months (technical visit is FOC) or paid visitation (RM65).    

You will receive appointment details via SMS within 48 hours.

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

2.Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user

Password: user

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi to configure the WiFi parameters.

6. You may change the Wi-Fi Name and the Wi-Fi Password as per your preferences, then click "Apply".

7. Your Wi-Fi Name and password has been changed. Kindly ensure to reconnect your WiFi according your new WiFi name and password.

The New Astro First serves as the one-stop, ultimate home cinema offering the biggest and latest local and international blockbuster films where you can:-

• Enjoy value for money viewing for local and international movies from only RM15* per movie or RM17* for UHD movies (*excluding tax).
• Stream each rented movie for as many times as you like within 48 hours* (*unless stated otherwise) anytime, anywhere via On Demand on your Astro Box or Astro GO.
• Watch local/regional movies or international movies from Hollywood studios as recent as 2 weeks or 3 months respectively from Malaysia's cinematic release, in addition to exclusive titles only available on Astro First.

STEP 1

Identify your remote control:

a)   Remote control with Astro logo at the bottom of the remote, proceed to STEP 2.

b)   Remote control with Astro logo at the top of the remote, proceed to STEP 4

‍

STEP 2 (Astro Logo at the bottom of the Remote)

On your remote, press the “set tv” button and set tv instructions will be displayed on top of your screen:

‍

STEP 3

Follow the steps appear on the TV screen to sync your Astro remote and complete the setup.

‍

STEP 4 (Astro Logo atthe top of the Remote)

Press and hold “tv input” key on bottom left of the remote for 3 seconds until the LED blinks twice.

STEP 5

Enter the 2-digit TV Code of your TV Brand and the LED will blink twice:

‍

STEP 6

Try out the TV controls (TV Standby or adjust Volume) to check if they are working correctly.

‍

STEP 7

Press ok and wait for the LED to blink twice to save the settings.

Unfortunately, you can't. My Astro is an easy-to-use, free mobile phone app and responsive web portal that helps Astro customers manage their Astro accounts. Astro customers can watch their favourite shows anytime, anywhere using the Astro GO app which is included in their subscription.

Starting 16 February 2024, you may be asked to perform Astro ID verification when you log in to their Astro account on digital platforms such as www.astro.com.my, Astro GO, My Astro etc. This 2-step process encompasses verifying your email address or phone number and re-entering of your existing password.
 

You will receive an email within 45 minutes of payment made to let you know whether your advance payment is successful or not. If your payment has failed, you may call Astro's Contact Centre at 03-9543 3838 or wait for an Astro representative to be in contact with you within 2 working days to assist you with your order.

For customers who wish to have their physical tax invoices reprinted, there will be a flat fee of RM10.00 levied as part of the process which has been implemented since year 2015.

Visit our page to find out about our new packs.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Navigate to IP Diagnostics and press "OK".

STEP 5    

IP Diagnostics information will be displayed.

No, there are no penalty fees for the Mesh WiFi devices should you wish to terminate Astro Fibre within/after 24 months. 

Yes, you are entitled to a free Ultra/Ulti box with free standard installation upon signing up Astro Fibre with a new 24-month contract.

The new packs come with 200 hours of Cloud recording by default. If your current recordings exceed 200 hours, the system will delete the exceeded hours once your package has been changed, starting with the oldest recordings first.  

If you would like to retain the previous recordings which exceed 200 hours, you may opt for a selection of 400 or 1500 Cloud Recording hours at a chargeable rate of RM12 or RM15 per month (excl. govt tax) respectively. Or else, you may subscribe to the Platinum pack which comes with complimentary access to 1500 hours of Cloud Recording.

We encourage customers to ensure their TV compatibility with the Astro Multiroom (Smart TV) app first before making any purchase here.

If you are still experiencing any issues, please contact us at wecare@astro.com.my or call or WhatsApp us at 03-9543 3838 and our agents will be happy to assist you.

1. For WiFi connection:
   • For Internet speeds up to 300Mbps, the user needs to have minimum WiFi 802.11n (5GHz) capabilities
   • For Internet speeds up to 500Mbps, the user needs to have minimum WiFi 802.11ac (5GHz) capabilities
   • For Internet speeds up to 800Mbps, the user needs to have minimum WiFi 802.11ax (5GHz) capabilities
2. ​For Wired connection:
   • The users need to use Cat5e Network cable or better and have their device equipped with 1Gbit Network Interface Card (NIC)
3. A summary of the minimum specifications for devices as tabulated below:

1. Number of WiFi antennas in the client device
2. Distance and WiFi signal strength between client device and RGW/Mesh AP
3. Overall WiFi signal congestion/pollution in area
4. Total number of devices connected to the RGW/Mesh AP

• Distance from the RGW/Mesh AP
• Client's Wi-Fi hardware specifications/capabilities
• Overall Wi-Fi signal quality in the area

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.

1. Try  loading the site on a different device.

  Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.

  If the website doesn't load on another device, the problem is either with the network or the website itself.

2. Restart your computer.

  Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.

3. Try loading the site in a different browser.

  There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.

4. Temporarily disable your antivirus program.

  Your antivirus software may be interfering with your ability to load certain websites.

  Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.

5. Reset  your modem and router.

  Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.

6. Check  your computer's date and time settings.

  If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.

  Check your computer or mobile device's clock to make sure that it is set to the correct time and date.

In the  event the problem persists, please provide below details for further  escalation:

  i. List of websites effected.          

  ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.  

  iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.          

  iv. Run the Ping Test -  Please click here for Ping Test guideline.

 Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

Step 1: Separate Your Wi-Fi Network Name

First, you need to set up your Wi-Fi to Dual-band in order to be less susceptible to interference, and allows you to choose between the 2.4GHz or 5GHz bands when connecting a device. A Wi-Fi frequency of 5GHz is best when you are near your router, and 2.4GHz is best for when you are far from your router.

• Check the bottom of your router for a website or IP address, username, and password.

Below are details for a standard login based on a standard router issued by ISP (Telekom Malaysia, Maxis, and Time dot Com)

• Login to your account
• Identify your Wi-fi Settings (This could be in advanced settings)
• Identify both the 2.4GHz and 5GHz options.
• Split the signals by renaming the 2.4GHz and 5GHz signals respectively, and make sure both are enabled.
• For detailed instructions based on router model, on how to separate your Wi-Fi, click here and choose the option according to your ISP and router brand.

Step 2: Factory reset your Ultra Box by following the steps below.

a. Press the Home button on your remote

b. Go to your settings page

c. Scroll down and select Reset/Restore

d. Select restore factory settings and proceed

e. Enter your PIN to access restore factory settings (default pin: 0000)

f. Choose restore and wait until the box reboots automatically. This may take around 2 minutes and you will see the Astro logo again when it's done.

You will be able to check your balance, switch to e-billing, request for payment barcode and request for reconnect at standard telco rate.

For Residential Astro Pay TV customers: Yes, you are allowed to change your package to the one that best suits your entertainment needs. You may make the following pack changes:  

1. Pack upgrades

1. Movement within Entertainment, Movies or Sports (e.g., switching from Sports to Entertainment)

1. Movement within Premium pack (to a different combination of content)

For these changes, you will remain on same contract duration, or you can choose to change to longer commitment. If you downgrade your packs, you will be charged a cancellation fee for pack, and you can then choose a new contract for the new pack. Kindly note additional contract details for Disney+ Hotstar and Netflix.  

(Please refer to the section "Changes to your Astro Contract" for more details)

Not all shows/channels will be available on the Plug & Play Box as this depends on contractual rights with specific guidelines on the entitlement of these shows/channels and what you have as a part of your subscription.

• Customers subscribing to Plug & Play Box with or without Astro Broadband will not have access to 1 (one) Channel - NHK World

Please be assured that we are continuously working hard to make more content available on the Plug & Play Box.

If you prefer to have all these channels, we recommend that you choose the Satellite dish option for the Ultra or Ulti Box.

Unavailable channels are as below:

Please note that only one Disney+ Hotstar access is bundled to each TV Pack subscription which allows two concurrent streams on Disney+ Hotstar. 

Please check SMS received on the unsuccessful payment status and should you require further clarification contact your issuing bank for clarification or contact us via WhatsApp.

Information of the PPV CH200 cessation has been announced on CH200 from 1 - 7 October prior to the PPV cessation. Once again, we regret any inconvenience caused.

Unfortunately, this means that you are using a TV model that does not support 4K UHD resolution (Sony BRAVIA 4K GB, Sony BRAVIA 4K UR or Sony BRAVIA VH). Not to worry, we are working with the Sony team to ensure you will be able to enjoy these 4K UHD channels soon. We will keep you posted once these channels are available to you!

Please contact the courier agent directly to change the retrieval date from the initially agreed date and time.

Yes, however we do advise keeping your subscription while your TV is being fixed to avoid having to download the app again.

Yes, you can sign up for auto-debit after your account has been activated via My Astro.
 
Alternatively, you may also call our Customer Contact Centre at 03-9543 3838 for assistance or to enquire about any current Auto Debit promotions.

The Download/Upload for each of the speed is as follow:

50Mbps/20Mbps

100Mbps/50Mbps

500Mbps/100Mbps

800Mbps/200Mbps

*Actual download/upload speeds is dependent on external factors, including but not limited to the distance between your devices and the WiFi router, network capacity and the number of connected users, the quality of your internal wiring, any obstructions of WiFi signals, the signal strength of wireless connection from your devices and if you are using a wireless connection. 

You are attempting to play a content that is not part of your subscription. If you are not able to play a content that you are subscribed to, proceed to submit report via WhatsApp or Feedback Form.

For existing Astro Fibre customers with the WiFi 6 Huawei K562e router, youwould need to upgrade to the latest RG21 router in order to access the AstroFibre  with a one-off fee of RM300 (excluding SST). For any enquiries, please contact our Customer ContactCentre at 03 - 9543 1543and an Astro agent will be available to assist you immediately.

You may register up to four (4) devices.

To remove devices on Astro GO, click on Settings > Registered Devices to view and remove a device(s) from the list of devices registered to your Astro ID.

Yes, you may upgrade to the Ultra Box if you are currently on the Entertainment or Movie Pack. If you are on the 500Mbps or 800Mbps plan, the upgrade will be free. However, a one-time fee of RM100 (excluding Govt. Tax) will apply if you are on the 50Mbps or 100Mbps plan. Please call or WhatsApp our Customer Contact Centre at 03-9543 3838 if you would like to make this upgrade. Please refer to the table below for the complete guide for Ultra Box upgrade:

Yes,existing Astro & Broadband customers within contract or out of contract can subscribe to Astro Fibre offer. The 24-month contract will be renewed.

However, your contract with Maxis/Allo needs to be terminated before signing up to this offer. An early cancellation fee applies if you are still within contract.

‍*Subject to Terms &Conditions of your contract

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Preferences and press "OK".

STEP 3  

Navigate to Language and press "OK".

STEP 4    

Choose your language preferences and press "OK".

STEP 5  

Select Yes, continue and press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer  than 15 minutes.

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Black port at D-Link Router and direct to the computer/laptop).    

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.    

3. On the address bar, please go to tplinkwifi.net and to access to below login page. Type the Username and Password, then click "Login".

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your router previously, the password may be  different)

For example, below is the login details of the above router:

Username: admin

Password: TIMECE24

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, choose Basic and then click Wireless tab on the left menu to access to below screen.

6. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

7. You may change the Wireless Network Name (SSID) and the Password to follow your preferences, then click "Save"  for the changes to take  place.

Please reconnect to the new wireless name with the new password once completed.

‍