Visit our page to find out about our new packs.

1. Please standby  computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.254 and below page  will appear.

If below box appear, please enter required details:

USERNAME: Administrator

PASSWORD: (ACCESS KEY AT THE RGW STICKER)

(These are the defaults, if you have done previous configuration on your router the password may be different)

4. Once enter into the page "'TECHNICOLOR TG784N V3'', you may follow below steps to get the best wireless channel information.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. In order to get the best wireless channel, click "Wireless Scan" to scan available surroundings wireless Channel.

D. Please choose channel with lesser number of usage.

Example in below case, you may choose channel 4.

5. To configure wireless channel, please proceed with below steps.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. Then, click "Configure" to change the channel selection (automatic to manual) and other configuration option.

D. Please ensure below items:

i. WLAN Enable: Tick

ii. Interface Enable: Tick

iii. Change the Channel Selection to Manual

iv. Change the wireless Channel based on Step 4(D).

v. Once completed the selection, click the "Apply" button.

STEP 1    

On your remote, press the ... button and the Channel Guide page will be displayed on your screen.

STEP 2    

Select the channel you would like to remove as favourite and press "OK".

STEP 3  

Select "Remove from Favourite" and press "OK".

STEP 4    

You are successfully removed the channel from favourite list when this screen appears.

You must subscribe to an Astro subscription (NJOI customers are not eligible) in order to get the Ulti Box. 

‍

The eligibility criteria for the Ulti Box are as follows:

New Customers

All new Astro customers with a monthly subscription fee of below RM100 will be entitled to select the Ulti Box upon signing up for Astro’s packages. 

‍

Existing Customers (Box Upgrade for Primary or Multiroom)

Existing customers are required to have an internet connection at home with a recommended internet speed of 10Mbps and above in order to upgrade your existing box to Ulti Box. 

Note: 

·      Existing Ultra Box customers are not eligible for a swap to the Ulti Box.

·      If your existing box is a PVR, you will lose access to all the recordings stored in the PVR

‍

Multiroom (New subscription)

Customers subscribing for an additional multiroom subscription are entitled to select the Ulti Box as part of the subscription.

Unfortunately, you can't. My Astro is an easy-to-use, free mobile phone app and responsive web portal that helps Astro customers manage their Astro accounts. Astro customers can watch their favourite shows anytime, anywhere using the Astro GO app which is included in their subscription.

Please disregard the reminder if payment had been made and do check if you have any outstanding balance on Astro Quick Pay.

We would need you to  run few tests in order for us to understand your issue and to assist you in fixing the problem.

You may proceed with the troubleshooting steps below which should not require any longer than 15 minutes.

1. Please run each of the tests according to your your Laptop/PC Software.
2. Compile the pictures / screenshots of your test results in one file (i.e Microsof Word document, PDF file) and attach them in the Support Ticket below in order for us to assist you further:
   • List of websites effected.
   • Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.
   • Run the Traceroute Test - Please click here for Traceroute Test guideline.          
   • Run the Ping Test - Please click here for Ping Test guideline.
3. Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.

A Ping Test shows how long it takes for packets to reach host.

A Traceroute Test traces the route of packets to destination host from our server.

Yes, all Astro customers with a Disney+ Hotstar subscription can access the app on the Ultra/Ulti Box. To access the app, please refer here. 

Yes, switching package is allowed. However, switching package from Non-Deal to Deal bundle will refresh a new 24-month contract.

Please call our Customer Contact Centre or WhatsApp "DH Help" at 03 9543 3838 to cancel your Disney+ Hotstar 3-months add-on pass with Astro. 

The Malaysia Communication and Multimedia Commission (MCMC)has issued a directive to all telecommunication companies (telcos) to block the sending and receiving of SMS with URL links. The move is aimed at preventing users from becoming victims of online scams. This exercise is applicable for all person-to-person SMS with URL links sent to or received from local and international mobile numbers, which has already taken effect as of 2 May 2023.

The minimum internet speed required to stream via Ultra Plug & Play Box is 30Mbps for 4K UHD viewing, and Ultra/Ulti Plug & Play is 10Mbps for HD viewing. For better streaming experience, we recommend 100Mbps and above.

If your account is suspended or disconnected, you will retain the existing subscription when you reconnect. However, if you plan to make any changes after the reconnection, you can only select from the new packs.

If your existing Netflix account is linked with your Astro subscription, your Netflix account will resume on the previous method of payment. If you linked a new Netflix account with your Astro subscription, cancelling Astro service will also cancel your Netflix account.

1. Unifi netis brand

The following shows an Interface based on Unifi router

1. Launch Web Browser and enter the default's gateway's IP address (192.168.1.1) in the address bar.

1. Enter Username and Password.
   1. Username = tmadmin
   2. Password = Adm@xxxx (xxxx refers to last four digits of MAC address)

1. Choose WLAN -> wlan0 (2.4GHz) Basic Setting. Note down on SSID.

1. Choose WLAN -> wlan1 (5GHz). Compare SSID with previous SSID.

1. If SSID for wlan0 (2.4GHz) and wlan1 (5GHz) are the same. Change wlan1 (5GHz) SSID by adding number 5(i.e. ifuni_5G) to differentiate from 2.4 GHz. Click Apply Changes.

Note: Connection to Wi-Fi may be temporarily loss while the changes is updated.

Slow browsing using LAN cable

Looks like there is something wrong with your service connection.

Please run the Speed Test and attach the picture or screenshot of the speed test in the Feedback Form below, in order for us to provide further assistances.

Click here for Speed Test guideline.

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.

Slow browsing using Wi-Fi

1. Router Positioning

Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.

i) High vs. Low

Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible  interferences.

ii) Concrete & Metals

Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement  as this area is usually enclosed by a lot of concrete, which can be almost  impossible for Wi-Fi signals to penetrate.

iii) Distance to Router

The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.

Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put  it at one end of the house.

2. Wireless Interference & Noise

You've probably never noticed but there  are wireless signals all around you wherever you go and they're passing  through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.

Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:

i) Microwaves

ii) Bluetooth Devices

iii) Cordless Phone

3. Surrounding Wi-Fi signals

A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel overlap. This can be  somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many routers within close proximity.

Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels for you automatically,  but sometimes it's better to investigate and find the best channel yourself.

 

4. Usage

More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/ Netflix.

Fortunately, if this is the case, you can prioritize your own network  traffic by enabling Quality of Service in your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

 

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

Yes,existing Astro & Broadband customers within contract or out of contract can subscribe to Astro Fibre offer. The 24-month contract will be renewed.

However, your contract with Maxis/Allo needs to be terminated before signing up to this offer. An early cancellation fee applies if you are still within contract.

‍*Subject to Terms &Conditions of your contract

The Ultra Box is Astro's latest generation of 4K UHD enabled box with Cloud recording feature, redesigned new interface, and UHD resolution. Just connect the all-new Ultra Box to the internet and take control of your entertainment and explore over 110,000 videos that are waiting to be streamed, anytime. With the ability to record as many shows as you want simultaneously.

The new interface on Astro Ultra Box offers an enhanced viewing experience with a brand-new look and feel with features such as:

·        New Home Screen - Everything you see is yours

·        Discover VOD - Discover 110k videos, stream anytime, anywhere including in 4K UHD

·        Search - Search faster and easier

·        Play from Start - You missed the start? Just restart

·        Stop Here, Continue There - Stop on one screen and continue on another device

·        Multi-Screen - Stream seamlessly across any device

·        Cloud Recording - Record all the programmes you want at the same time

.       **Continuous viewing - Enable to continue watching your favorite shows during raining
 

Note: ** Except 4K UHD, Astro First and all radio channels

You can add a reminder to pay your bill, on your Google Calendar with one click. Enjoy uninterrupted services, by remembering to pay your bill on time.

You can track your ticket status by contacting us via WhatsApp or call us at 03-9543 3838.

Please refer to "Upon downloading the app, what do I do next?" question on this FAQ here or call us at 03-9543 3838 for any further queries.

STEP 1    

On your remote, press the Home button and the menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3    

Navigate to Restore and press "OK".

STEP 4    

Navigate to Restore Factory Settings and press "OK".

STEP 5

Enter your PIN to access this setting. (Default PIN is 0000).

STEP 6    

Navigate to Restore and  press "OK" to  confirm your selection.    

Otherwise, navigate to Cancel, go back to remain the settings.

STEP 7    

Please wait while the box restoring defaults and will reboot once complete.

STEP 8    

Your box will automatically restart and display this screen.

Click here to follow New Installation Settings guide for Satellite

Click here to follow New Installation Settings guide for Plug and Play

I am sorry you can't. While we understand the value customers see in choosing their preferred service/pack individually, the packaging of channels/services in the new packs are necessary for us to offer content/services at an affordable price to our customers.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Audio and press "OK".

STEP 4

Navigate to your preferred selection and press “OK”.

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2  

Navigate to Settings.

STEP 3  

Navigate to S/PDIF Audio and press "OK".

‍

STEP 4    

Navigate to your preferred selection and press “OK”.

Connect your PVR to Wi-Fi and enjoy access to our library of Video On Demand. Replay old seasons, catch-up latest episodes of your favourite shows, anytime you want. To connect your PVR, follow the steps below:

STEP 1    

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2    

Navigate to SETTINGS and press “OK”.

STEP 3    

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4  

Navigate to Network and press "OK".

STEP 5    

Navigate to Wi-Fi and press "OK".

STEP 6    

Select New Connection and press "OK".

STEP 7    

Select your Wi-Fi network and navigate to "Connect".

STEP 8    

Please enter the password to connect to your network and press "OK".

STEP 9    

You are successfully connected when this screen appears.

The new packs and access to Netflix on the Ultra Box and Ulti Box is available for Astro IPTV customers.