Yes, Mesh WiFi add-on is available for both Astro Fibre Bundle and Astro Fibre subscription.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

To continue enjoying your PVR decoder and service, you must maintain a minimum monthly subscription fee of RM60 (not inclusive of the recording fee and Govt. Tax).

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be experiencing this problem.    

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

You have exceeded the maximum number of registered devices allowed. To manage devices on Astro GO, go to Settings > Registered Devices to view / remove devices from the list of registered devices to your account.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.
 

Step 1: You request for a move. 

‍
Step 2: One of our agents will contact you within 24 hours to set an appointment if you’re using Self Service - Astro Self-Service Portal.

‍
Step 3: You will receive a reminder of your appointment an hour before your scheduled time.

‍
Step 4: The technician will dismantle your satellite dish.

If there is no satellite dish, customers should dismantle the modem, router, and decoder by themselves.

‍
Step 5: You will need to transport your device(s) to your new home.

‍
Step 6: The technician will reinstall your satellite dish, (including modems and routers for broadband customers) at your new home based on the schedule appointment.

‍

Note For IPTV Customers:

1. Upon relocation request, all exiting IPTV customers will be converted to our Astro & Broadband service. Customers can choose to have standard Astro service with satellite dish, or unicast Plug & Play without satellite dish.

2. If customers choose to have satellite dish, an additional RM150.00 will be charged for satellite installation. If customers choose to have unicast Plug & Play service, no satellite dish is required, hence no extra charge will be incurred.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your Ultra Box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

Connect your Ultra Box/Ulti Box today and get the full value for your subscription. We believe we can provide you the best entertainment experience in Malaysia, and it all starts with connecting your box to the internet.

Want to enjoy these features for free?

• Continue watching Astro even when it’s raining.
• Binge-watch and catch-up to 110,000 videos on-demand from Malaysia, Hollywood, Korea, China, Bollywood and more anytime.
• Create multiple profiles in your house to enjoy a personalized Astro experience, with shows recommended to you based on your interest. There is a Kids-friendly version for your little ones as well.
• Rewind, pause and fast-forward shows and matches so that you will never miss another moment.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Scroll to Network Settings and press "OK". Select New Wi-Fi Connection and press "OK".

‍

STEP 4

Select your Wi-Fi network and press "OK". Please enter the password to connect to your network.

STEP 5

You have successfully connected when this screen appears.

We would need you to run few tests in order for us to understand your issue and to assist you in fixing the problem.

This will not take longer than 15 minutes.

1. Please run each of  the test using your laptop or personal desktop by connecting to your Astro Fibre.
2. Please list down the impacted website (Provide us the complete URL i.e. www.astro.com.my).
3. We need you to run below tests and compile the pictures or screenshots of your test results into one file (i.e Microsof Word document, PDF file) and send to our agent in order for us to assist you further:
   • Run the Ping & Traceroute Test - For guidance, please click here for Ping & Traceroute Test guideline. 
   • You may run this by connecting via WiFi or LAN cable. Your test result will appears as per below screen and take a screenshot.

• Run the Speed Test - For guidance, please click here for Speed Test guideline.

We need you to run the Speed Test using both WiFi connection and LAN cable.

4. Once you've gathered all the results, attach in Feedback Form for further assistance.

At this point in time, the Disney+ Hotstar app on the Ultra or Ulti Box does not support Dolby audio. We are working to enable this in a future update. 

SST of 6% and 8% will be applied accordingly to your bundle services:

1. 8% SST to Astro TV Pack
2. 6% SST to Astro Fibre

Your account may be under suspension. To resolve this issue, proceed to submit report via WhatsApp or Feedback Form.

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.
2. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem connection

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - LAN  port) to PC/Laptop.

4. If you have change the password in Selfcare Time portal recently, please change the router configuration follows the new password made in  Selfcare, but if you didn't make any changes, please go to Step 5.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 2 / Option 3

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.

2. Gently remove fiber optic cable and  blow / wipe the tip of the fibre cable. This is to clean up the cable in  order to avoid any interferences.

3. Re-insert the fiber cable to the  optical port behind the modem.

4. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem Connection

Router Connection

5.  Make Sure both cables on Modem (LAN Port 4 /LAN Port 3 for second decoder) and Astro Decoder (Network Port) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after  reboot.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.


Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/ power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

Option 5

1. Please ensure LAN cable is directly connected to modem port LAN 1.

2. Please use different LAN port if LAN 1 port is still off / not working.

3. If the issue persists, submit your feedback form for further assistance.

Astro introduces the new Ulti Box with a redesigned new interface, Cloud recording feature, enhanced search capabilities and more. Just connect the all new Ulti Box to the Internet and take control of your entertainment and stream up to 110,000 videos on demand, anytime. 

‍

The features of the new Ulti Box include:

·      New Home Screen - Everything you see is yours

·      Discover Video on Demand (VOD) - Discover 110,000 videos, stream anytime, anywhere

·      Search - Search for your favorite show or video faster and easier

·      Play from Start - Missed the start of the show? Just restart.

·      Stop Here, Continue There -Stop on one screen and continue on another device

·      Multi-Screen - Stream seamlessly across any device

·      Cloud Recording - Record all the programmers you want at the same time

.      **Continuous viewing - Enable to continue watching your favorite shows during raining.

‍

We recommend an Internet speed of 10Mbps and above for optimal access to cloud recording, streaming on demand videos and search functions. 

Note: ** Except 4K UHD, Astro First and all radio channels

You may proceed with the following troubleshooting steps and it shouldn't take you much longer than 15 minutes.

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN  cable to the Black port at D-Link Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://dlinkrouter.local./ and below  page will appear. (These are the defaults and if you have done a  configuration on your router previously, the password may be different)

Username: admin

Password: (Leave the field blank)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, click Settings and then choose Wireless.

6. Below screen will appear to configure the wireless setting. Since this is a dual band router, you will have 2 Wi-Fi Names (SSID); i.e. 2.4GHz and 5GHz.

i. For 2.4GHz setting, click Advanced Settings to display more available options.

ii. To change the channel, click the drop-down arrow for Wi-Fi Channel, then select your desired channel.

Choose between 1 to 13 (Suggested channels : 1,6,11). Click Save for the changes to take place.

The router will auto reboot and connection will re-establish after few minutes.

iii. Next, for 5GHz setting, click Advanced Settings to display more available options to make changes on the wireless channel for 5GHz.

iv. Click the drop-down arrow for Wi-Fi Channel, then select your desired channel from the selection.

v. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few  minutes.

Your monthly bill of the previous and new pack will be prorated. This will be reflected into your bill accordingly.

Your bill will be waived upon request.

1. Ensure power cable  is connected tightly.    

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

No, you will not be automatically switched to the new pricing. To perform a manual switch, please contact us at 03-9543 3838.

Yes, eKYC verification is mandatory. In addition, this verification process helps to reduce manual handling of customer's personal information and secure against unauthorised usage.

For customers with Entertainment Plus, Movies Plus, Sports Plus, Premium 2, Premium 3, and Platinum Pack 

1. Launch Netflix from the home screen or via remote control. 

2. Click on Get Started

3. If you are an existing Netflix customer, please fill in the email address and password associated with your Netflix account. Once successfully completed, all existing settings and watching history on your Netflix account will be brought over. If you are a new Netflix customer, create a new account by filling in your email address and a password for your new Netflix account. 

4. In the next screen, you will be shown your default Netflix package “Standard”, you can choose to upgrade to “Premium” here. 

5. The final screen provides a summary of your account including your email. Click Start Watching to enjoy Netflix on your Ultra/Ulti Box. 

‍

For Non-Entertainment Plus, Premium 2, Premium 3, and Platinum Pack Pack customers (New Netflix customers) 

1. Launch Netflix from the home screen or via remote control.

2. Click on Join Now

3. Create a new account by filling in your email address and a password for your new Netflix account. 

4. The final screen provides a summary of your account including your email. Click Start Watching to enjoy Netflix on your Ultra/Ulti Box. 

Note: The Netflix plan will be defaulted to Premium, you may select ‘Change Plan’ to choose the ‘Standard’ plan. 

‍

For Non-Entertainment Plus Pack, Premium 2, Premium 3, and Platinum Pack customers (Existing Netflix customers) 

1. Launch Netflix from the home screen or via remote control 

2. Click on Sign-in 

3. If you are an existing Netflix customer, please fill in the email address and password associated with your Netflix account. 

4. You will be able to start watching Netflix on your Ultra/Ulti Box once you log in.

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.
2. Ensure the fiber cable from your wall socket and modem is securely connected.

Notes: You might be connected to LAN 1 if backbone is Maxis

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option  2/ Option 3/ Option 5/ Option 6

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.    

2. Ensure the fiber cable from your wall socket and modem is securely connected.

3. Ensure both cables on the Modem (LAN Port 2) and Router (WAN Port - Red port) are properly connected.

Notes: You might be connected to LAN 1  if backbone is Maxis
 

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. Please make sure both cables on Router (Any Yellow port) and Astro Decoder (Network Port behind decoder) are properly inserted.

5. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

6. If the issue persists, submit your feedback form and attach your modem light indicator picture/ video for further assistance.
 

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

Your Astro account number is a 10-digit combination e.g.08XXXXXXXX. You may log on to My Astro Portal, select "Account" , and you may find your 10-digit account number above your address, or refer to the top right-hand corner of your bill.

The warranty period will be 24 months.

If you would like more information or to provide feedback, kindly log in to our support page via support.astro.com.my. For more questions regarding Astro Pack, you may reach out to us via call at 03-7481 1000 (Monday to Friday, 9AM – 6PM exclude public holidays).
 

Any Astro GO compatible device (mobile/tablet/PC) and Multiroom Smart TV* compatible TVs will benefit from Astro GO+. 

Depending on your service, it is mandatory to return some devices as per our T&Cs, whilst other devices should be disposed of and recycled at collection centres registered under the Department of Environment. To find out what you should do with your devices after service termination, please click here.

Starting 16 February 2024, you may be asked to perform Astro ID verification when you log in to their Astro account on digital platforms such as www.astro.com.my, Astro GO, My Astro etc. This 2-step process encompasses verifying your email address or phone number and re-entering of your existing password.
 

Step 1:

Type ASTRO<space>BARCODE<space>10 digit account number

Example: ASTRO BARCODE 0866603852

Step 2:

Send SMS to 66688

*Standard telco charges and Terms and Conditions apply

STEP 1    

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Take a look at the Smart Card Status.

Please check your internet speed and connection status via internet connection test. If your internet is working fine and the issue persists, proceed to submit report via WhatsApp or Feedback Form.

Yes, as part of our Astro Fibre Movies & Sports Campaign, new Astro Fibre customers can enjoy 50Mbps + the Movies/Movies+/Sports/Sports+ Pack TV bundle for a special price from only RM164.99/month when they sign up within the campaign period, with more than RM800 savings in total.

Yes, you can purchase Astro First and Astro Best content by using the app and web. Refer below for the steps to purchase movies via this app and web. Thereafter, you can watch them on Astro Go.

STEP 1    

On your remote, press the ... button and the Channel Guide page will be displayed on your screen.

STEP 2    

Select the channel you would like to unlock and press "OK".

STEP 3    

Select "Unlock Channel" and press "OK".

STEP 4    

Enter the PIN to unblock the channel.

STEP 5    

You are successfully unlocked the channel when this screen appears.

If you sign up Astro & Broadband with standard Ultra & Ulti box (DBB), all channels are available.  

However, there are channels that will not be available with Ultra/Ulti Plug & Play Box which are NHK World (398).

No. If you are a non-Astro subscriber, you will still be able to create an Astro ID, but access and use of Astro's digital services will be limited. If you are an Astro subscriber, please link your Astro ID to your Astro account number to enjoy exclusive access to all of Astro's digital services.

Astro & Broadband offers Astro content with Astro Fibre, Maxis Fibre Broadband and Allo City Broadband for customers to enjoy the best entertainment through Astro while staying connected with high-speed internet.

With the current Astro & Broadband plans, customers will enjoy substantial savings by choosing their desired broadband speed from 30Mbps - 800Mbps to accompany their Astro packages.

STEP 1

‍

Try to change channels on your Astro  remote.

INDICATOR: LED blinking 3 times / NO LED blink

SOLUTION: Replace new battery

Proceed to Step 2.

‍

INDICATOR: LED blinking 1 time

Confirm it's not your Astro remote faulty, let's proceed to Step 3.

‍

STEP 2

If issue remain after the battery replacement, this might be due to a faulty Astro remote.

Try changing the channel manually directly from the box front panel (If any).

If it's working, you might need to  replace your Astro remote.

You may walk-in to our nearest Customer Service Center for the replacement.

STEP 3

You need to refresh the box setting by initiate manually from box front panel.    

Refer to Refresh Box setting Guide steps here.

For existing Astro Fibre customers with the WiFi 6 Huawei K562e router, youwould need to upgrade to the latest RG21 router in order to access the AstroFibre  with a one-off fee of RM300 (excluding SST). For any enquiries, please contact our Customer ContactCentre at 03 - 9543 1543and an Astro agent will be available to assist you immediately.

You can proceed with below BTS if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to Diagnostics and press “OK”.

STEP 5

Refer to the signal strength on your screen.

If it is 65 or higher, please take the screenshot and submit your feedback form.

If it is below 65, please go to Step 6.

STEP 6

Switch off the power for your box and  make sure that the adapter’s power light is off.

STEP 7

Unscrew the satellite cable from the box  and pull it out.

STEP 8

Plug the satellite cable back into the  box and screw it back securely.

STEP 9

Switch on the power for your box and make sure that the adapter’s power light is on. Please wait for 5 minutes.

STEP 10

Turn on your box. You should no longer be experiencing this issue.

If issue persist, please submit the issue on our Feedback Form with error details and attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized  Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

You can add a new Netflix account to your bill through CH 741 or clicking the Netflix button on the remote control. Please enter the email address you would like to use for Netflix subscription and ensure the Billing partner is Astro.  

If you would like to transfer your existing Netflix Account to be charged under Astro bill, please follow the steps below:  

1. Cancel your existing subscription with Netflix  

1. Once the remaining duration of your existing subscription has ended, you may proceed to subscribe for Netflix via Astro bill  

1. To subscribe, go to CH 741 and enter the email address used for your previous subscription with Netflix  

1. Once successfully completed, all existing settings and watching history on your Netflix account will be brought over  

Thank you for your interest in returning your Astro Box & Smart card/SIM card. By returning these items, you are playing your part in preserving our environment as we will refurbish the box and return it to circulation or recycle it.

All Astro box and smartcard/SIM cards are also property of Astro and as per our current T&Cs, customers are required to return them upon termination of Astro services.

Disney+ Hotstar is available to Astro customers on the Disney+ Hotstar app on Android and iOS devices and website (DisneyPlusHotstar.my) which is accessible on tablets and connected TVs. Unfortunately, Disney+ Hotstar is not available on Astro GO. However, customers can enjoy it on the big screen via the Ultra or Ulti Box. 

Yes, you will enjoy an Ulti box when subscribing to Primary/Entertainment/ Movie Pack OR an Ultra box when subscribing to Sports/Sports+/Movies+/Premium 1/Premium 2/Premium 3/Platinum Pack.

You will get FREE installation for both Ultra/Ulti box upon signing up with Astro & Broadband.