As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3. Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

No, you do not have to prepare any documents before handing your equipment over to the courier agent/installer! All you must do is get your equipment ready before the courier agent/installer arrives to ensure a smooth handover process.

If the bill has been paid, there will not be any additional service tax charge. However, if the bill has been issued by Astro but has not been paid, then the 8% Service Tax will be reflected in the next bill with adjustments on the new tax rate for services rendered from 1st March onwards.

Example:
Bills issued on 15th February will be charged the 6% SST. Customers will see proration for 8% from 1st – 14th March in the next bill issued on 15th March 2024. If you have fully paid your February bill before 1st March, the Service Tax will remains at 6%. You will be able to see the adjustment reflected in your next bill.

For customers with the Ultra or Ulti Box, please ensure to provide your latest contact details to our Astro agent during the call to terminate your account, this includes your mobile number and house address. If you still need further help, please contact us at 03-9543 3838.

Please ensure you:

a. Have your original identification card “MyKad” (Front & Back) with you (Malaysian).

b. Have your original Passport & Visa with you (Non-Malaysian).

c. Are in a brightly lit environment

When using our One Time Payment (OTP) method, you may register more than one credit card per account. However, a single card account can only be used for a maximum of three accounts for OTP transactions.

When using our auto-debit facility, you can only register one card with Astro. Any subsequent card registrations will override the current one.

No, you will not be charged 8% Service Tax for reconnection performed before 1st March 2024. Only reconnections executed on or after 1st March 2024 are subject to the 8% Service Tax.

STEP 1: Try Changing the Channel

Remote LED Indicator Guide:

LED blinks 3 times or doesn't blink at all:
Replace the remote batteries and try again

LED blinks once:
Remote is working fine. Proceed to the next step.

STEP 2: Test Manual Channel Change

Try changing the channel manually directly from the box front panel (If any).
If it's working, you might need to replace your Astro remote, this might be due to a faulty Astro remote.
You can visit the nearest Astro Service Center to replace your remote.

STEP 3: Refresh Box Settings

Manually reload the decoder settings using the front panel of the decoder.
Refer to Refresh Box setting Guide steps here.

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

You will still need to authorise the transaction from your SecureGo registered device. 

Step 1: On another device, perform the transaction via My Astro app 

Step 2: Tap on the push notification you receive on your SecureGo registered device 

Step 3: Tap Approve or Reject to authorise the transaction, and you're done! 

Yes. To change the language, go to the app’s side menu, then go to Settings and select the preferred interface language.

Watch this video or follow below steps to fix your WiFi connectivity issue

Skyworth RG21

1. Please connect your computer or laptop to your Astro Fibre router using WiFi or LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).
2. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user
Password: user

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click WLAN to configure the WiFi parameters.

6. To change the channel on 2.4G, click the drop-down arrow for Channel, then select your desired channel.

7. Then, click "Save & Apply" for the changes to take place.

8. You may make the same changes for 5G by click the drop-down arrow for Channel, then select your desired channel.

9. Then, click "Save & Apply" for the changes to take place.

If you cancel your subscription before completing the 12-month contract period, an early termination fee may apply in accordance with your contract terms. The fee is calculated by multiplying your monthly subscription fee by the number of months remaining in your contract.

Subscribing to any of the Astro X3 pack will not affect your existing Astro plan. The Astro X3 pack is treated as a separate subscription, with a new account created under a different email address. Your current Astro plan and its services will remain active and unchanged unless you choose to terminate them separately.

STEP 1

On your remote, press the HOME button.

STEP 2

Navigate to SETTINGS icon and press "OK".

STEP 3

Navigate to Manage Satellite Frequency and press “OK”.

STEP 4

Choose Test Satellite Frequency and press “OK”.

STEP 5

Choose "Confirm" to continue Test Satellite Frequency and press “OK”.

STEP 6

Satellite Frequency Test progress screen will be displayed.

STEP 7

The test result will be displayed once completed.

By changing from a higher contract duration e.g., 24-months commitment period to lower contract duration e.g., 12-months, a proration of the cancellation fee will be applicable whereby you will be charged per contract's month balance against the maximum cancellation fee agreed upon during sign up for the offer.

A proration of the cancellation fee will be applicable whereby you will be charged per contract's month balance against the maximum cancellation fee agreed upon during sign up for the offer.

You will start a new contract with 12-months commitment and receive the corresponding discount for that duration.

Check out how a cancellation fee is calculated with examples via this link:

This error indicates that you have reached the maximum number of simultaneous video streams across devices for one (1) account. To stop seeing this error, please stop streaming on one of your other devices.

• If you have recently purchased your Astro pack or made any changes to your pack on or after 9th November you can stream on two (2) concurrent screens

• If you have not made any changes you can stream on four (4) concurrent screens.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.

Step 1: Separate Your Wi-Fi Network Name

First, you need to set up your Wi-Fi to Dual-band in order to be less susceptible to interference, and allows you to choose between the 2.4GHz or 5GHz bands when connecting a device. A Wi-Fi frequency of 5GHz is best when you are near your router, and 2.4GHz is best for when you are far from your router.

• Check the bottom of your router for a website or IP address, username, and password.

Below are details for a standard login based on a standard router issued by ISP (Telekom Malaysia, Maxis, and Time dot Com)

• Login to your account
• Identify your Wi-fi Settings (This could be in advanced settings)
• Identify both the 2.4GHz and 5GHz options.
• Split the signals by renaming the 2.4GHz and 5GHz signals respectively, and make sure both are enabled.
• For detailed instructions based on router model, on how to separate your Wi-Fi, click here and choose the option according to your ISP and router brand.

Step 2: Factory reset your Ultra Box by following the steps below.

a. Press the Home button on your remote

b. Go to your settings page

c. Scroll down and select Reset/Restore

d. Select restore factory settings and proceed

e. Enter your PIN to access restore factory settings (default pin: 0000)

f. Choose restore and wait until the box reboots automatically. This may take around 2 minutes and you will see the Astro logo again when it's done.

Kindly download the Astro Smart TV app from your Smart TV’s app store and follow the steps on the screen to log in.

After completing the subscription process, you will be able to access the iQIYI App on the Ultra/Ulti Box by following the steps below:

On your Ultra/Ulti Box
Step 1: At the Home menu, go to the App Rail and select "iQIYI"
Step 2: Click "OK" on your Astro remote
Step 3: While on the iQIYI App Home Page, navigate to "VIP account" located at the top left pane and click "Login". A page with a QR Code will be presented on your TV screen
Step 4: Scan the QR code using your mobile device and you will be directed to the iQIYI mobile app
Step 5: Follow the steps under "On Mobile App" below to pair your iQIYI account with your Ultra/Ulti Box

On the iQIYI Mobile App
Step 1: Download the iQIYI App on your mobile device
Step 2: At the login page, select "Continue with Astro"
Step 3: Log in with your Astro ID
Step 4: Click on the "Me" icon located at the bottom of the screen, and you will be presented with your iQIYI profile page
Step 5: Click on the in-app QR code scanner located at the top right corner of the screen
Step 6: Scan the QR Code displayed on your TV screen with the in-app QR code scanner. Refer to Step 3 under "On your Ultra/Ulti Box" above
Step 7: The screen on your TV will reload automatically and the iQIYI App home screen will be displayed. Now, you can enjoy the iQIYI App on your Ultra/Ulti Box!

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to TV Settings and press “OK”.

STEP 4

Navigate to your preferred selection and press “OK”.

STEP 5

Navigate to Save and press "OK" to confirm your selection.

We try to make as many movies and TV shows available for download. However, for some titles, while we may have the rights to offer them via streaming, we may not be able to offer them for download.

STEP 1

Check on the adapter's power light.

If the adapter's power light is ON, please refer to Blank Screen troubleshooting steps here.

Otherwise, if the adapter's power light is OFF, switch off the power for your box.

STEP 2

Ensure power cable is connected tightly.

Plug in power cable to different power socket and switch on the plug.

You should no longer be experiencing this problem.

If issue remains, proceed to STEP 3.

STEP 3

Try a different power socket to connect the equipment.

Turn on the power socket and check the adapter's power light.

If there is no light on your power adaptor's, please submit the issue on our Feedback Form with error details and provide your sim card number for assistance.

Please indicate in the form if any lightning strike/thunderstorm/power trip occurred.

STEP 1
On your remote, press the Home button and the Home Page will be displayed on your screen.

STEP 2
Navigate to Profile.

STEP 3
The Profile Selection Screen will be displayed.

STEP 4
Navigate to Edit Profile.

STEP 5
Choose a profile to edit.

STEP 6
Navigate to Delete Profile.

STEP 7
Click Confirm to delete your profile.

STEP 8
The deleted profile will be removed from the Profile Selection Screen.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Guide.

STEP 3

Select the channel you would like to add to favourite list and press "OK".

STEP 4

Select "Add to Favourites" and press "OK".

STEP 5

You are successfully added the channel to favourite list when this screen appears.

STEP 6

Your selected channel will have a heart tagging after added as favourite.

Please ensure that you have subscribed to the mentioned channel.
If you're subscribed to this channel, follow below steps.

STEP 1
You need to refresh the signal on your box.
Refer to Refresh signal of your box guide.

STEP 2
If issue persist after 30 minutes, proceed to submit report via WhatsApp or Feedback Form.

Yes, you have the option to transfer the credit balance to another active Astro account. It will be considered as payment to that account and is subject to Astro's terms & conditions.

Upon logging in or creating a new account, you will be prompted to link your Astro Account to your Astro ID.If you do not have an Astro ID, please follow the steps in to create one and linking if to your Astro Account:

• Step 1: Click “Create Now” on the Astro ID login page
• Step 2: Enter your name, email or mobile number, and your preferred password
• Step 3: Key in the account holder’s MyKad number followed by the Astro account or smartcard number. Refer to your Astro Bill for the account number (10 digits).
• Step 4: Enter the 6-digit verification code sent to your mobile or click on the email verification link to verify
• Step 5: You’re all set!

1. Sending a WhatsApp message with "Hi" to 03-9543 3838 for assistance.

2. Submitting a feedback form at www.astro.com.my/contactus/form.

Alternatively, for any issues related to Prime Video, users can visit the Prime Video Help page for further assistance from Prime Video.

If you are unable to log in to the Astro Smart TV app, please follow the steps below:

1. Verify Your Astro ID Credentials

• Ensure you are using the correct Astro ID (email address/mobile number) and password.
• If you have forgotten your password, reset it via the Astro login page.

2. Check Your Internet Connection

• Ensure your Smart TV is connected to the internet.
• Test your internet connection by opening another app on the TV.
• Restart your router and Smart TV if necessary.

3. Update the Astro App and TV Software

• Make sure the Astro app is updated to the latest version.
• Check that your Smart TV firmware/software is up to date.

4. Restart the App

• Close the Astro app completely.
• Reopen the app and try signing in again.

5. Reinstall the Astro App

• Uninstall the Astro app from your Smart TV.
• Download and install it again from your TV's app store.
• Attempt to log in once more.

If you are still unable to log in, proceed to submit report via WhatsApp or Feedback Form and provide:

• Smart TV brand and model
• Screenshot/photo of the error message
• Astro ID (email address used for login)
• Details of the troubleshooting steps already performed

This information will help the support team investigate and resolve the issue more quickly.

Astro & Broadband comes with 24-month contract commitment.

Customers with a Netflix Premium account are allowed to watch on up to 4 supported devices in 4K UHD and Netflix Spatial Audio. In addition, Netflix Premium subscribers are also allowed to download shows to watch offline on 6 devices at a time.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.1.254 and below page will appear.

The default login of the router as below. If you have done a configuration on your router previously, the password may be different.

Username: user
Password: Router S/N (Available on the sticker at the back of the router)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the left menu, choose Wireless 2.4GHz and then click Basic Settings tab on the left menu to access to below screen.

6. You may change the Wireless Network Name (SSID) and the SSID Password to follow your preferences, then click "Save" for the changes to take place.

Please reconnect to the new wireless name with the new password once completed.

7. Since this is a dual band router, you will have 2 Wireless Network Names (SSID) i.e. 2.4GHz and 5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

You may change the Wireless Network Name (SSID) and the SSID Password to follow your preferences for 5GHz by choosing Wireless 5GHz then click Basic Settings.

Click "Save" for the changes to take place and reconnect to the new wireless name with the new password once completed.

You may check your bills and outstanding via My Astro web or My Astro app via this link.

Note: Bill statements and payment history are not available on WhatsApp. For a more complete billing experience, including access to your payment history, download and use the My Astro app.

1. Open/Download the My Astro app or visit My Astro web.

2. Login with your Astro ID.

3. Go to Account.

4. Under Billing, tap on Bill Delivery Method.

5. Select 'Email (FREE)' and tap 'Proceed'.

6. Tap 'Confirm'.

7. Select 'Approve' to update bill delivery method.

8. A successful notification will be displayed.

Astro customers can enjoy a special offer of RM13.90/month (RRP RM13.90/month) when they subscribe to WeTV VIP via Astro.

Please contact your issuing bank to enable card-not-present (CNP) transactions. This security measure helps us to protect your card information from being misused in fraudulent transactions.

Having trouble with your phone line ?

You may proceed to contact dedicated service provider directly - 1 800 8211 23

No, currently Simply South is not available for offline viewing.

The "coming soon" label on some streaming apps on your TV and the "Apps" page of Astro's website allows our customers to stay on top of new launches as they happen! Stay tuned for these upcoming streaming apps so you can access even more content that you love from across the world.

The Download function offers an alternative to streaming so that you can watch TV shows and movies offline anywhere.

You can start downloading a movie/TV show by clicking on the "Download” button. Kindly note that you can only download one title at the time. Other titles will be in queue and will start downloading automatically as soon as the first download is complete.

Once you have downloaded a title, the progress icon will show “Complete” and you may find your downloaded content by checking “My Library” > “Downloads”.

*To save on data usage, we recommend downloading via Wi-Fi.

Downloaded content retention periods vary according to the type of content.

1. Each movie – minimum 2 Days
2. Each TV series episode - minimum 7 Days

The number of days left for you to view your content in offline mode is shown for each piece of downloaded content for your reference. Expired content will be automatically deleted from the app, freeing up your device storage.

Huawei HG8240

Huawei HG850A

FIBER HOME

ALCATEL LUCENT

HUAWEI

ZTE

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.
2. Ensure the fiber cable from your wall socket and modem is securely connected.

Modem connection with Fiber Cable

Modem connection with Copper Cable

Notes: You might be connected to LAN 1 if backbone is Maxis

Router connection

Technicolor Router

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option 2/ Option 3/ Option 5/ Option 6

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.

2. Ensure the fiber cable from your wall socket and modem is securely connected.

3. Ensure both cables on the Modem (LAN Port 2) and Router (WAN Port - Red port) are properly connected.

Modem connection with Fiber Cable

Modem connection with Copper Cable

Notes: You might be connected to LAN 1 if backbone is Maxis

Router connection

Technicolor Router

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. Please make sure both cables on Router (Any Yellow port) and Astro Decoder (Network Port behind decoder) are properly inserted.

DMT4 (Hybrid mode)

DMT5 (Hybrid mode)

DMT4 (IP mode)

DMT5 (IP mode)

5. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

6. If the issue persists, submit your feedback form and attach your modem light indicator picture/ video for further assistance.

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

After successfully adding ZEE5 Premium to your bill, follow the simple steps below to stream ZEE5 on your Ultra/Ulti Box:

Step 1: Go to your Astro Home Page and click “ZEE5” under the Apps rail
Step 2: Scan the QR code on screen with your mobile device
Step 3: Log in with an existing ZEE5 ID or sign up for a new account. Then, enter the activation code displayed on your TV screen into the ZEE5 mobile app.
Step 4: Now, enjoy streaming ZEE5 on your Ultra/Ulti Box!
Please ensure that the email address used to log in to the app is the same one used to purchase your ZEE5 premium subscription.

1. Launch the Simply South icon on your Ultra and Ulti box
2. Click on “Log in” button via top menu in Simply South app
3. Follow the instructions displayed on your TV screen

Yes, customer may choose to have different billing method for each different account.

Physical bill charging will only apply to the account that has opted for paper bills.

No, SecureGo can only be tied to 1 device per Astro ID.

Yes, you may return Astro equipment even after being charged for the box fee. You can choose either to opt for:

1. At-Home Collection: Please contact Astro to schedule for equipment collection. A courier partner agent or installer will call for the collection.
2. Self-drop-off: Customers are required to self-pack their Ultra Box or Ulti Box and SIM Card into a box and drop the parcel off at any of our listed courier partner branch.

After successfully returning the box, Astro will proceed to waive off the box fee within 30 days from the confirmation date of the returned items to our Astro warehouse. However, if you’ve made the payment, we will proceed with the refund to your registered credit card or to your account.

Starting 29th April 2025 onwards, the Sun NXT app will be available on the Ultra/Ulti Box for all Astro customers to enjoy on the big screen, web app or/and mobile app.

You will receive a 6-digit SMS OTP number sent to your registered mobile number.

Customers who downgraded their package from Astro Broadband Bundle/Astro Fibre Bundle to Astro TV Pack only will be charged 8% Service Tax effective 1^st March 2024 onwards. Any adjustment or proration charges incurred before the downgrade will be calculated based on 8% service tax in the next bill, in line with the latest package downgrade.

For Astro Ultra Box or Ulti Boxes, you will be able to see an itemised charge called "Box Fee” in your Astro bill.