STEP 1  

Check your current software version on your box.

If the software version updated (Refer to Table 1), proceed to STEP 2.

If software version different from Table 1, click here for Software Update guide.        

Once software is updated, tune to the impacted channel.        

If issue persist, proceed to STEP 2.

STEP 2    

Run Test Satellite Frequency.    

Click here for the guide.

If Test Pass, proceed to submit report here.

‍

Guide to  submit report:    

At Feedback Type select "I have  missing channel".    

Fill up all the required  information and submit.    

Please indicate if you agreed to recontract for 12 months (technical visit is FOC) or paid visitation  (RM65).    

You will receive appointment  details via SMS within 48 hours.

If Test Fail, proceed to STEP 3.

‍STEP 3    

Proceed to Update Satellite Frequency.    

Click here for the guide.    

Once completed, tune to the impacted channel.            

If issue persist, proceed to submit report here.

‍

Guide to  submit report:    

At Feedback Type select "I have  missing channel".    

Fill up all the required  information and submit.    

Please indicate if you agreed to recontract for 12 months (technical visit is FOC) or paid visitation  (RM65).    

You will receive appointment  details via SMS within 48 hours.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Navigate to IP Diagnostics and press "OK".

STEP 5    

IP Diagnostics information will be displayed.

You may access it by pressing "200' on your Astro remote control whilst watching TV.

STEP 1    

Switch OFF the power of your Ultra / Ulti box and make sure that the adapter's power light is off.

STEP 2    

Switch ON the power of your Ultra / Ulti box and make sure that the adapter's power light is on.

‍

STEP 3  

Put the box on standby mode.

STEP 4

Press and hold the Home button on the box.

STEP 5    

Wait until "boot" appear on the front panel and released.

STEP 6

When “boot” appears, press “Standby”,  “Left “, “Up” continuously until Auto Update appear on box screen and Software Update progress on TV.

‍

‍

STEP 1    

Switch OFF the power of your box and make sure that the adapter's power light is off.

‍

STEP 2

Switch ON the power of your box and make sure that the adapter's power light is on.

STEP 3

Press Standby, Ch+, Standby keys on the box simultaneously when the "boot" message appears on the box front  panel.

The Software Update progress screen will appears.    

The update will take 10 - 15 minutes to complete. Please be patience.

STEP 1  

Switch OFF the power of your box and make sure that the adapter's power light is off.

STEP 2    

Switch ON the power of your box and make sure that the adapter's power light is on.

STEP 3

Press the standby button repeatedly after switch on the power.

STEP 4

Press "OK".

STEP 5    

The Software Update progress screen will appears.

The update will take 10 - 15 minutes to complete.

Please be patience.

You can proceed with below BTS if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to Diagnostics and press “OK”.

STEP 5

Refer to the signal strength on your screen.

If it is 65 or higher, please take the screenshot and submit your feedback form.

If it is below 65, please go to Step 6.

STEP 6

Switch off the power for your box and  make sure that the adapter’s power light is off.

STEP 7

Unscrew the satellite cable from the box  and pull it out.

STEP 8

Plug the satellite cable back into the  box and screw it back securely.

STEP 9

Switch on the power for your box and make sure that the adapter’s power light is on. Please wait for 5 minutes.

STEP 10

Turn on your box. You should no longer be experiencing this issue.

If issue persist, please submit the issue on our Feedback Form with error details and attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized  Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

STEP 1    

On your remote, press the HOME button.

‍

STEP 2    

Navigate to Update Satellite Frequency and press “OK”.

‍

STEP 3  

Choose Test Satellite Frequency and press “OK”.

‍

STEP 4  

Select Yes, continue and press "OK" to start the test.    

Otherwise, select No, go back to cancel.

‍

STEP 5    

Satellite Frequency Test progress screen will be displayed.

‍

STEP 6    

The test result will be displayed once completed.    

Press "OK" to go back to channel.

All Astro customers and non-customers who have an Astro ID will no longer be able to log in to our digital platforms using their usernames. Users will experience this change if they currently do not use an email address or mobile number to login, for example: johndoe2023.

You can recover your Netflix login here or at astro.com.my/Netflix

Step 1: Head to astro.com.my/Netflix

Step 2: At the FAQ section look for "How to recover my Netflix login email and password

For Residential Astro Pay TV customers: You may change your contract from e.g., 12-month to 24-month without incurring a switching fee or cancellation fee. However, if you change your contract from e.g., 24-month to 12-month, will be charged a cancellation fee accordingly if still within minimum term (contract) period. No switching fee applicable.

We encourage customers to ensure their TV compatibility with the Astro Multiroom (Smart TV) app first before making any purchase here.

If you are still experiencing any issues, please contact us at wecare@astro.com.my or call or WhatsApp us at 03-9543 3838 and our agents will be happy to assist you.

We would need you to  run few tests in order for us to understand your issue and to assist you in fixing the problem.

You may proceed with the troubleshooting steps below which should not require any longer than 15 minutes.

1. Please run each of the tests according to your your Laptop/ PC Software.

2. Compile the pictures/ screenshots of your test results in one file (i.e Microsof Word document, PDF file) and  attach them in the Support Ticket below in order for us to assist you further:

• List of websites effected.
• Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.
• Run the Traceroute Test - Please click here for Traceroute Test guideline.
• Run the Ping Test -  Please click here for Ping Test guideline.

3. Once you've gathered all the results, kindly send them all through the Feedback Form below,

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

No. If you are a non-Astro subscriber, you will still be able to create an Astro ID, but access and use of Astro's digital services will be limited. If you are an Astro subscriber, please link your Astro ID to your Astro account number to enjoy exclusive access to all of Astro's digital services.

Yes, you may cancel your Astro Fibre order before service activation, however, kindly note that there is a cancellation charge of RM212 (inclusive of SST) for any service cancellation done 48 hrs before scheduled appointment.

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

By default, the band steering featured is disabled. Follow these steps to enable it.

Note: Band Steering is called Dual-band Combination in the router web interface.

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).
2. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user
Password: user

 

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi to configure the WiFi parameters.

6. Click on Dual-band Combination button to enable the Band Steering.

7. A pop-up message will appear showing "The device network may be disconnected when dual-band combination is enabled". Click "OK" to proceed.

8. Set the Wi-Fi name and Wi-Fi password based on customer's preferences. Then click "Apply" for the changes to take place.

Please reconnect to the new Wi-Fi name with the new password once completed.

You can subscribe to new packs via  

• Online - astro.com.my  
• WhatsApp GET ASTRO (for new customers) or SWITCH (for existing customers) to 03-9543 3838
• Astro Customer Service Centres.

Once your Plug & Play Box has been activated, a courier service will reach out to you within TWO (2) weeks for a time for them to pick up the old Astro box and SIM card/Smartcard.

1. Ensure that all cables have been plugged out of the old Astro box. To remove the white satellite cable from your old Astro box, simply hold the cable, twist, and gently pull.
2. Set aside these items to be ready for our delivery partner to pick up from you:

• Old Astro Box
• Old Astro Smartcard/SIM Card (leave this in your Astro Box)

3. When a courier arrives at your residence, do confirm that they are collecting items on behalf of Astro.
4. Allow the courier to check the serial number of the Astro box.
5. Hand them all the items for return, and you're done!

STEP 1
Check the internet connectivity by run the Test Connection.
Refer Run Test Connection.


STEP 2
Verify the average speedtest based on the Test Connection result.
a. Above 10Mbps - Proceed to STEP 5
b. Less then 10 Mbps - Proceed to STEP 3

Notes: Minimum 10 Mbps internet speed from box requires in order to get a stable connection.



STEP 3
Check the connection to the box either using Ethernet (LAN cable) or Wi-Fi.
a. If using Ethernet (LAN cable) - Connect to Live Agent for help.
b. If using Wi-Fi - Proceed to STEP 4



STEP 4
Check location of the decoder and router.
a. If nearby (within 1.5m) - Try connect to box from router using LAN cable.
b. If far (more than 1.5m) / No LAN cable - Proceed STEP 5



STEP 5
Reboot router, modem and decoder.
If issue persist, please try again after 30mins to 1 hour. Connect to live agent if persist after 30 mins to 1 hour.

You can access the self-help service 24 hours a day for the following: 

1. Check account balance.

2. Refresh your Smartcard if your account is active but TV screen displays "This channel is not included in your subscription" or "We apologise for the service interruption".

3. Check application status.

4. Guide on Self Service troubleshooting guide via SMS Link.

5.  Check trouble ticket appointment announcement.

6.  Apps Related Self Service login & Activation guide via SMS Link.

7.  Apps Related FAQ Details via SMS Link.

No, your rewards cannot be transferred to another person or exchanged for cash.

Any packages with Entertainment Plus, Movies Plus & Sports Plus will include Netflix. The default Netflix offering is Netflix Standard (2 screens and HD viewing) as part of your Entertainment Plus, Movies Plus and Sports Plus subscription. You can upgrade up to Netflix Premium (4 screens and 4K UHD viewing) at a price of RM 10 (inclusive of govt. tax).  

Note: For the above subscriptions, you may use the email address used for your existing subscription with Netflix to activate and the future billing for Netflix will be transferred to your Astro bundle charges. For users that are billed for Netflix through Apple before joining the Astro bundle, remember to cancel your Apple billing arrangement after activating the Astro bundle else you may be double charged for your Netflix account.

If you do not have a bundle which includes Netflix, you may also add a new Netflix subscription to your Astro Bill for billing convenience.

1. Please standby computer/laptop to access to the internet and connection must be via (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 or www.tplinkwifi.net and below page will appear.

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your router previously, the password may be different

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.
 

5. From the top menu, choose Basic and then click Wireless tab on the left menu to access to below screen.

6. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

7. You may change the Wireless Network Name (SSID) and the Password to follow your preferences, then click "Save"  for the changes to take place.

Please reconnect to the new wireless name with the new password once completed.

Astro GO is a companion app that is complimentary for all Astro subscribers and allows up to 2 users to stream at the same time. 200 hours of cloud recording* come complimentary with your Pay TV subscription. 

Astro GO+ is an add-on service that enables up to 4 users to stream Astro GO and/or Multiroom Smart TV** at the same time. The amount of cloud recording storage will also be increased to 1500 hours. 

 *Cloud recording hours are shared across your Astro Box, Astro GO and Multiroom Smart TV 

** Provided that you have a Multiroom Smart TV subscription

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2  

Navigate to Settings.

STEP 3  

Navigate to S/PDIF Audio and press "OK".

‍

STEP 4    

Navigate to your preferred selection and press “OK”.

No, the Ulti Box does not support 4K UHD content. If you would like to watch Astro's 4K UHD content, please sign up for an Ultra box at Astro Ultra Box and Ulti Box | Astro.

You may check your bills and outstanding via:

• Channel 200 from your Astro Box.
• Astro Self Self-Serve Portal or MyAstro App via this link.
• WhatsApp "Payment" to 03 9543 3838 and follow the steps provided.

There will be no changes to your Netflix account when you move to a new address.