Unfortunately, you will no longer be able to access Disney+ Hotstar via Astro if you cancel your Astro subscription with Disney+ Hotstar entitlement. 

You can proceed with below BTS if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to Diagnostics and press “OK”.

STEP 5

Refer to the signal strength on your screen.

If it is 65 or higher, please take the screenshot and submit your feedback form.

If it is below 65, please go to Step 6.

STEP 6

Switch off the power for your box and  make sure that the adapter’s power light is off.

STEP 7

Unscrew the satellite cable from the box  and pull it out.

STEP 8

Plug the satellite cable back into the  box and screw it back securely.

STEP 9

Switch on the power for your box and make sure that the adapter’s power light is on. Please wait for 5 minutes.

STEP 10

Turn on your box. You should no longer be experiencing this issue.

If issue persist, please submit the issue on our Feedback Form with error details and attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized  Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which could cause the issue.

3. If issue persists, submit your Feedback Form for further assistance.

Please refer to these FAQs for more information, or click here to learn more and sign up for the Ulti Box. Alternatively, you may call 03-7481 8000 to get in touch with an Astro representative.

Advance payment is only applicable to Astro TV pack purchases. If you subscribe to an Astro Fibre+TV bundle, only one month of your TV subscription fee (excluding tax) is required to be paid upon sign-up. The full tax amount and the first-month subscription fee for Astro Fibre will be paid on your first month's bill.

Your monthly bill of the previous and new pack will be prorated. This will be reflected into your bill accordingly.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Audio Delay and press "OK".

STEP 4

Navigate to your preferred selection and press “OK”.

Slow browsing using LAN cable

Looks like there is something wrong with your service connection.

Please run the Speed Test and attach the picture or screenshot of the speed test in the Feedback Form below, in order for us to provide further assistances.

Click here for Speed Test guideline.

Quick Info

A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
 

Slow browsing using Wi-Fi

1. Router Positioning

Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
 

i) High vs. Low

Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
 

ii) Concrete & Metals

Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
 

iii) Distance to Router

The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
 

Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.

2. Wireless Interference & Noise

You've probably never noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.

Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can  still cause interference. Some common causes of interference include:

i) Microwaves

ii) Bluetooth Devices

iii) Cordless Phone

3. Surrounding Wi-Fi signals

A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel  overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many routers within close proximity.

Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

 

4. Usage

More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/ Netflix.

Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.


Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

STEP 1  

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2  

Navigate to Settings.

STEP 3    

Navigate to Remote Control Settings and press "OK".

STEP 4  

Follow the steps appear on the screen to sync your Astro remote.

ransfer of Equipment Ownership

A request to transfer the equipment’s ownership from the existing account holder to a new account holder. ‍

Note: Transfer of Equipment Ownership is not applicable for IPTV and NJOI account.

Merge of Equipment

A request from the account holder to merge the equipment from two different accounts into one account, provided the equipment must be within the same service address and registered under the same accountholder’s name.

Split of Equipment

A request from the account holder to split the equipment from one account to two different accounts and registered under the same account holder’s name.

You may proceed with the following troubleshooting steps and it shouldn't take you much longer than 15 minutes.

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN  cable to the Black port at D-Link Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://dlinkrouter.local./ and below  page will appear. (These are the defaults and if you have done a  configuration on your router previously, the password may be different)

Username: admin

Password: (Leave the field blank)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, click Settings and then choose Wireless.

6. Below screen will appear to configure the wireless setting. Since this is a dual band router, you will have 2 Wi-Fi Names (SSID); i.e. 2.4GHz and 5GHz.

i. For 2.4GHz setting, click Advanced Settings to display more available options.

ii. To change the channel, click the drop-down arrow for Wi-Fi Channel, then select your desired channel.

Choose between 1 to 13 (Suggested channels : 1,6,11). Click Save for the changes to take place.

The router will auto reboot and connection will re-establish after few minutes.

iii. Next, for 5GHz setting, click Advanced Settings to display more available options to make changes on the wireless channel for 5GHz.

iv. Click the drop-down arrow for Wi-Fi Channel, then select your desired channel from the selection.

v. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few  minutes.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.

1. Try  loading the site on a different device.

  Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.

  If the website doesn't load on another device, the problem is either with the network or the website itself.

2. Restart your computer.

  Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.

3. Try loading the site in a different browser.

  There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.

4. Temporarily disable your antivirus program.

  Your antivirus software may be interfering with your ability to load certain websites.

  Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.

5. Reset  your modem and router.

  Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.

6. Check  your computer's date and time settings.

  If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.

  Check your computer or mobile device's clock to make sure that it is set to the correct time and date.

In the  event the problem persists, please provide below details for further  escalation:

  i. List of websites effected.          

  ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.  

  iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.          

  iv. Run the Ping Test -  Please click here for Ping Test guideline.

 Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

You may report the incident on WhatsApp at 03-95433838 by typing PNP and our dedicated agents will attend to your matter. Please have your Airway Bill tracking numbers ready for validation.

If a replacement box/Astro SIM card is deemed necessary, a new Plug &Play Box and a new Astro SIM card will be couriered to your service address.

My Astro is an easy-to-use, free mobile phone app and responsive web portal that helps Astro customers to manage their Astro accounts. My Astro allows customers to manage their accounts, pay bills, and get any support they need. In addition, customers can find and purchase the latest shows to be viewed on their Astro Box or on Astro GO. Customers can also receive news about Astro's latest products and content offerings.

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.
2. Ensure the fiber cable from your wall socket and modem is securely connected.

Notes: You might be connected to LAN 1 if backbone is Maxis

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option  2/ Option 3/ Option 5/ Option 6

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.    

2. Ensure the fiber cable from your wall socket and modem is securely connected.

3. Ensure both cables on the Modem (LAN Port 2) and Router (WAN Port - Red port) are properly connected.

Notes: You might be connected to LAN 1  if backbone is Maxis
 

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. Please make sure both cables on Router (Any Yellow port) and Astro Decoder (Network Port behind decoder) are properly inserted.

5. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

6. If the issue persists, submit your feedback form and attach your modem light indicator picture/ video for further assistance.
 

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

Astro is continuously improving our user interface and introducing new features to our platforms to ensure that your Astro experience is more seamless, efficient and user-friendly.

For details on our latest interface, Picture-in-Picture mode and auto-start interactive mode on Astro GO, please click here. For enhancements to the Title Information Page, the ability to disable the Profile Selection Screen and adjustable auto-standby timing, please click here.

In addition, we have also recently introduced an infinite scrolling feature at the title information page and the ability to select the video quality directly from the video player. For more information, please click here.

STEP 1

Check on your TV input to ensure correct input selected.

If issue remains, switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Unplug the HDMI cable from your box and plug it back in securely.

STEP 3

Switch on the power for your box and make sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 4

Turn on your box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form with the error details and provide  sim card number for assistance.

electronic Know-Your-Customer (eKYC) is an online process of identifying and verifying individual customers using electronic means. This enables a person to be an Astro customer anytime and anywhere, hassle-free and helps to secure your Astro account by protecting it from unauthorised usage.

Mac OS X

1. Click the Go tab in the top menu bar and select Utilities from the drop-down menu.

2. Type "network utility" in the search bar in the top right-hand corner of the Utilities window and then hit the "Enter" key on your keyboard. 

3. Click the Network Utility icon to open the Network Utility window.

4. For Ping Test, select the Ping tab and then type the address you'd like to ping in the text box. Click Ping and wait for the ping results.
 

5. For Traceroute Test, select the Traceroute tab and then type the address you like to traceroute in the text box. Click Trace and wait for the traceroute results.
 

Windows 10

1. Click the Search icon (magnifying glass) in the bottom left-hand corner and type "cmd" into the search bar.

2. Select the Command Prompt app - it will be at the top of the list of search results as the best match.

3. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

Windows 7 & Vista

1. Open the Start menu by clicking the Windows icon at the bottom left-hand corner of the screen.

2. Type "cmd" in the search bar at the  bottom of the menu.

3. Click cmd found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows 8

1. Move the mouse to the right-hand corner of the screen to make the vertical menu bar (charm bar) appear. Click Search.

2. Type "cmd" in the search bar and hit the Enter key on your keyboard.

3. Click cmd that found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows XP

1. Click the Start button in the bottom left-hand corner of the screen.

2. Click the Run option in the right-hand column.

3. Type "cmd" in the text box and then hit the Enter key on your keyboard.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you'd like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

There will be no changes to your Netflix account when you move to a new address.

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

Please first ensure Disney+ Hotstar access is included and has been activated as part of your Astro subscription. Once you have completed your activation process, you can enjoy Disney+ Hotstar on the Ultra box with these simple steps:

• Step 1 -Press "Home' on your Astro remote control. On the apps rail, select "Disney+ Hotstar' app > OK > My Account

No, the Mesh WiFi add-on with Astro Fibre is available as subscription service and will not be tied to any device contract.

If you have a random Astro power cable, remote control or old box lying around at home, you are required to discard them only at registered collection centres for proper handling and management of e-waste in an environmentally sound manner. Click here to find a registered collection centre near you.

For all recycling-related questions, please click here.