Call our contact centre 03-9543 3838 or visit us at astro.com.my.

No, the Mesh WiFi add-on with Astro Fibre is available as subscription service and will not be tied to any device contract.

1. Please standby  computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.254 and below page  will appear.

If below box appear, please enter required details:

USERNAME: Administrator

PASSWORD: (ACCESS KEY AT THE RGW STICKER)

(These are the defaults, if you have done previous configuration on your router the password may be different)

4. Once enter into the page "'TECHNICOLOR TG784N V3'', you may follow below steps to get the best wireless channel information.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. In order to get the best wireless channel, click "Wireless Scan" to scan available surroundings wireless Channel.

D. Please choose channel with lesser number of usage.

Example in below case, you may choose channel 4.

5. To configure wireless channel, please proceed with below steps.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. Then, click "Configure" to change the channel selection (automatic to manual) and other configuration option.

D. Please ensure below items:

i. WLAN Enable: Tick

ii. Interface Enable: Tick

iii. Change the Channel Selection to Manual

iv. Change the wireless Channel based on Step 4(D).

v. Once completed the selection, click the "Apply" button.

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

Want to return your Ultra or Ulti Plug & Play Box? It's simple and free!

Here's what you can do with your unused Ultra/Ulti Plug & Play Box:

1. Return your device to us via Arranged Pick-up:

Step 1: Please call Astro's Contact Centre at 03-9543 3838 to schedule an arranged pick-up by one of our courier partners.

Step 2: Just sit back and relax! A courier agent will come to your doorstep to retrieve the devices.

Astro invests billions of ringgits in content annually to keep Malaysians entertained and informed. Hence, we work alongside industry players, content partners and regulators in protecting intellectual property so that Astro can continue to produce and aggregate compelling content for our viewers.

We continue to educate and raise awareness among the public and businesses about the economic and social losses caused by content piracy. You can play your part in combating piracy by reporting potential copyright infringement of Astro content to the Domestic Trade and Consumer Affairs Ministry (KPDNHEP) on the following channels:

• 1-800-886-800 (hotline)  
• 03-8882 6088 (Enforcement Command Centre)
• +6019-279 4317 (WhatsApp)

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to Installation Settings and press "OK".

STEP 4    

Enter your PIN to access this setting. (Default PIN is 0000).

STEP 5    

Navigate to Restore Factory Settings and press "OK".

STEP 6    

Navigate to Yes, continue and  press "OK" to  confirm your selection.    

Otherwise, navigate to No, go back to maintain the settings.

STEP 7    

Please reboot your box.

STEP 8    

New Installation Settings screen will appear.    

Click here to follow New Installation Settings guide.

The payment will take some time to reflect in My Astro app and web account. If you experience any further issues or it is still not reflecting in My Astro, please reach out to us via WhatsApp at 03-9543 3838 for more details.

1. Clearly indicate full name of Astro customer, contact number and Astro subscription account number when making each payment (e.g. on bank-in slips)
2. For Direct Debit, please contact your bank for standing instructions. Provide the full name of Astro customer and Astro account number. The Direct Debit service may not be available with all banks. Please check with your bank for confirmation of Direct Debit service.
3. Please inform us of any changes in billing address/information by contacting us via one of these platforms.

IMPORTANT NOTICE: To avoid any problems in payment processing, please pay only at authorised Astro payment channels

Yes, you will enjoy an Ulti box when subscribing to Primary/Entertainment/ Movie Pack OR an Ultra box when subscribing to Sports/Sports+/Movies+/Premium 1/Premium 2/Premium 3/Platinum Pack.

You will get FREE installation for both Ultra/Ulti box upon signing up with Astro & Broadband.

The amount you're charged depends on:

• Your contract period and how long's left of your minimum term from the date your subscriptions end, calculated in months.
• Your current box type - Ultra or Ulti/Other Astro Boxes
• The packages you subscribe to, including App services such as Disney+ Hotstar and Netflix

The promotion period of Astro Fibre’s Speed Upgrade Campaign is from 24 November 2023 until 31 May 2024.
 

Upon successful subscription, you will be able to view your chosen HD channels within 3 hours by keying in the channel numbers into your remote control. Please note that subscription through Channel 200 will take effect within 24 hours.

STEP 1    

On your remote, press the ... button and the Channel Guide page will be displayed on your screen.

STEP 2    

Select the channel you would like to remove as favourite and press "OK".

STEP 3  

Select "Remove from Favourite" and press "OK".

STEP 4    

You are successfully removed the channel from favourite list when this screen appears.

You can proceed with below troubleshooting if the weather is good. Ortherwise, you may try again later.

STEP 1
On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.


STEP 2
Navigate to SETTINGS and press “OK”.


STEP 3
Navigate to STB DIAGNOSTICS and press “OK”.


STEP 4
Refer to the signal strength % shown on the top left of your screen.
If it is 65% or higher, please go to WhatsApp to receive further help.
If it is below 65%, please go to STEP 5.


STEP 5
Switch off the power for your box and make sure that the adapter’s power light is off.


STEP 6
Unscrew the satellite cable from the box and pull it out.


STEP 7
Plug the satellite cable back into the box and screw it back securely.


STEP 8
Switch on the power for your box and make sure that the adapter’s power light is on.
Please wait for 5 minutes.


STEP 9
Turn on your box. You should no longer be experiencing this issue.
If issue persist, please attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized Dish
 If issue persist under a centralised satellite dish, please refer to your respective Building Management before contacting our agents.

STEP 1  

Press "HOME" button on your remote control.

STEP 2    

Navigate to Preferences and press "OK".

STEP 3  

Navigate to Auto Standby and press "OK".

STEP 4    

Navigate to your preferred selection and press “OK”.

STEP 5  

Select Yes, continue and then press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

You would need your 10-digit account number and your email address.

Only new and existing Astro Fibre customers with the latest RG21 router can use the Astro Fibre app.

No, you can remain in your current pack, however starting 9 November 2021, you would need to subscribe to the new packages to make any changes to your subscription. We strongly encourage customers to switch to the new packs to enjoy the best content experience from Astro.

Your bill statement will include details of your monthly subscription charges; e.g. charges for your chosen Astro packages and Broadband service. It will also show the time period of which your first bill will cover, as well as indicate how much the total charges are and when the payment due date is.

This Service Tax is imposed on customers of Pay TV broadcasting services by the Government. As such the Service Tax will be passed on to the customers.
 

Of course not! It is a value-added service introduced for your convenience.

As our customers deserve the best entertainment experience, Astro is refreshing its content and packages to offer more choice, value, flexibility, and better experience in a streaming world as part of the new Astro experience.  

The all-new Astro packs are designed for customers in the streaming and connected world, where they can stream all the shows they love on Ultra Box and Ulti Box. Customers can now enjoy their favourite shows all on Astro, from global streaming services like Netflix, Disney+ Hotstar, HBO GO, iQIYI, TVBAnywhere+ as well as all Astro's flagship shows and the best of live sports in one place, on the big screen. Our new packages offer unbeaten value, a greater variety of content and greater convenience, all made better with our Astro & Broadband for better connectivity.

Please make sure that:

1. You are logging in with the correct registered Astro ID (email or phone number) and password. If you can’t remember your password, please proceed to use the “forget password” function.
2. You have an Astro ID that is linked to an Astro account. (note: NJOI – linked users will not be able to log into Astro GO)
3. Your Astro account is active and not under suspension.

If the above points have been met, you may try some quick solutions below:

1. Clear the cache on your browser or app.
2. Check if you have the latest version of the browser or app.
3. Log out and log back into the browser or app.
4. Relaunch the browser or app.
5. Restart your mobile device.
6. Restart your internet connection.

Thank you for your interest in returning your Astro Box & Smart card/SIM card. By returning these items, you are playing your part in preserving our environment as we will refurbish the box and return it to circulation or recycle it.

All Astro box and smartcard/SIM cards are also property of Astro and as per our current T&Cs, customers are required to return them upon termination of Astro services.

To continue enjoying your PVR decoder and service, you must maintain a minimum monthly subscription fee of RM60 (not inclusive of the recording fee and Govt. Tax).

STEP 1  

On your remote, press the HOME button.

STEP 2

Navigate to SETTINGS icon and press "OK".

‍

STEP 3  

Navigate to Manage Satellite Frequency and press “OK”.

STEP 4

Choose Test Satellite Frequency and press “OK”.

STEP 5  

Choose "Confirm" to continue Test Satellite Frequency and press “OK”.

‍

STEP 6  

Satellite Frequency Test progress screen will be displayed.

‍

STEP 7  

The test result will be displayed once completed.

Currently the Multiroom (Smart TV) app is supported on four (4) brands with the software version listed below:

1. Sharp
2. Sony
3. LG
4. Samsung

STEP 1

Switch OFF the power of your Ultra / Ulti box and make sure that the adapter's power light is off.

STEP 2

Switch ON the power of your Ultra / Ulti  box and make sure that the adapter's power light is on.

STEP 3

On your remote control, press the standby button repeatedly until the Startup Options appear on TV.

STEP 4    

Press "1".

‍

STEP 5

Press "1".

‍

STEP 6

The Software Update progress screen will appears.    

The update will take 10 - 15 minutes to  complete.    

Please be patience.

Photograph or scan your payment receipt, and send it to one of our contact platforms found here.

Video On Demand is FREE* for all Astro customers with connected Astro boxes (Ultra Box, Ulti Box, HD-PVR &PVR boxes). Aside from our extensive library of more than 110,000 video, you can also enjoy blockbuster movies on a pay-per-view basis. 

‍Please note that your default pin is 0000 to make any purchases. 

‍*Entitlement is based on subscription package.

STEP 1    

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Take a look at the Smart Card Status.

Astro Fibre is Astro’s own internet service that enables you to enjoy Astro content while staying connected with high-speed fibre broadband. Customers can enjoy substantial savings by choosing your desired broadband speed  to accompany your Astro TV packages. Customers can choose from two types of Astro Fibre offering:

1. Astro Fibre Bundle offers the best value proposition of 50Mbps to 800Mbps high-speed broadband bundled with Astro TV content packages including access to leading streaming services, creating a one-stop entertainment solution for its customers.
2. Astro Fibre is a standalone high-speed broadband service of 100Mbps to 800Mbps offering a powerful WiFi system leveraging the latest WiFi 6 router and a flexible mesh proposition.

If you are subscribed to Netflix via a bundle, Netflix comes by default as part of your entitlement.

If you are subscribed to Netflix as an a-la carte, the cancellation of Netflix can only be done via Netflix's Website, etc). This change will reflect in your next bill. From mid-December 2021 you may also cancel Netflix add-on through Astro Call Center.