You can proceed with below troubleshooting if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4

Refer to the signal strength % shown on the top left of your screen.

If it is 65% or higher, please take the screenshot and submit your Feedback Form.

If it is below 65%, please go to Step 5.

STEP 5

Switch off the power for your box and make sure that the adapter’s power light is off.

‍STEP 6

Unscrew the satellite cable from the box and pull it out.

STEP 7

Plug the satellite cable back into the box and screw it back securely.

STEP 8

Switch on the power for your box and make sure that the adapter’s power light is on.

Please wait for 5 minutes.

STEP 9

Turn on your box. You should no longer be experiencing this issue.

‍

If issue persist, please submit the issue on our Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

‍

Centralized Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

In your first Astro bill, the first month's bill will be deducted accordingly excluding tax. You will still need to pay the full tax amount for your first month as per your first month's bill.

Note: Advance payment is only applicable to Astro TV pack purchases. If you subscribe to an Astro Fibre + TV bundle, only one month of your TV subscription fee (excluding tax) is required to be paid upon sign-up. The full tax amount and the first-month subscription fee for Astro Fibre will be paid on your first month's bill.

STEP 1  

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3  

Navigate to STB Diagnostics and press "OK".

STEP 4    

Select Advanced Diagnostics and press "OK".

STEP 5  

Details information of Advanced Diagnostics screen will be displayed.

STEP 6    

Press down arrow on your remote to get more information.

Upon completion of the termination process, customer will receive one last closing bill stating the total amount due to Astro according to their billing option.

For customers who had opted to switch their billing option to e-bill or SMS bill, they will receive their final bill accordingly.

For customers who opted for paper bill, they will receive the final bill via paper bill. (The Paper Bill Charge will be applied).

Absolutely not. Astro wants to give our members the convenience of having all their favourite series, exciting originals, vernacular signatures, live sports and local blockbuster movies all in one place.

STEP 1
Check on the adapter's power light.
If the adapter's power light is ON, please refer to Blank Screen troubleshooting steps here.
Otherwise, if the adapter's power light  is OFF, switch off the power for your box.

STEP 2
Ensure power cable is connected tightly.
Plug in power cable to different power socket and switch on the plug.
You should no longer be experiencing this  problem.
If issue remains, proceed to STEP 3.

STEP 3
Try a different power socket to connect the equipment.
Turn on the power socket and check the adapter's power light.

If there is no light on your power adaptor's, please submit the issue on our Feedback Form and attach a picture of your smart card number for assistance.
Please indicate in the form if any lightning strike/thunderstorm/power trip occurred.

For technical visit, the current fees will remain unchanged i.e.: 8% Service Tax absorbed by Astro. As for installation fees, current fees will remain unchanged i.e.: 6% Service Tax has already been included in installation fees, as 2% will be absorbed by Astro.
 

If you add on the Mesh WiFi during your initial order of Astro Fibre, there is no additional installation fee. If you order the Mesh WiFi as an add-on at a later time, you will have to pay RM49 per installer visit. However, if you choose to have the Mesh WiFi delivered via courier in order to self-install your Mesh WiFi, there will be no installation or delivery fee charged.

The Personal Video Recorder (PVR) is Astro's High Definition (HD)decoder which comes with a recording function and can be connected to Wi-Fi to access videos on demand. The PVR comes with the following features:

HIGH DEFINITION (HD):High Definition offers greater detail than Standard Definition including vibrant colour and multi-dimensional audio.

CONTROL LIVE TV: Record, Pause, Play & Rewind your favourite TV programmes at any moment. The PVR comes with storage capacity of 500GB (200 hours of HD recording)

ON DEMAND: Experience the new way of watching Astro. Gain access to a library of up to 50,000 On Demand titles that you can pick and watch instantly.

Your account number will be used to identify/verify you for all After Sales-Services. You may also use your mobile number/ Astro smart card number/ NRIC number or Astro Box number.

Astro wants to give our members the convenience of having all their favourite series, exciting originals, vernacular signatures, live sports and local blockbuster movies in one place. Astro customers will be able to enjoy greater convenience by having Netflix bundled with their Astro subscription, consolidating the subscriptions, and providing easy access for payment in a single bill, at the best value.

STEP 1    

Check your current software version on your box.

If the software version updated (Refer to Table 1) , proceed to STEP 2.

If software version different from Table 1, click here for Software Update guide.

Once software is updated, tune to the impacted channel.        

If issue persist, proceed to STEP 2.

‍

STEP 2  

Run Test Satellite Frequency.    

Click here for the guide.

‍

If dCSS Scan Entrypoint Success, proceed to submit report here.

Guide to submit report:    

At Feedback Type select "I have Astro service related question/request" and Sub Category as "Technical Interruption".

Fill up all the required information and submit.    

Please indicate if you agreed  to recontract for 12 months (technical visit is FOC) or paid visitation (RM65).    

You will receive appointment details via SMS within 48 hours.

If dCSS Scan Entrypoint Fail, proceed to STEP 3.

‍

‍STEP 3    

Proceed to Update Satellite Frequency.

Click here for the guide.
Once completed, tune to the impacted channel.

If issue persist, proceed to submit report here.

‍

Guide to submit report:    

At Feedback Type select "I have Astro service related question/request" and Sub Category as "Technical Interruption".

Fill up all the required information and submit.    

Please indicate if you agreed to recontract for 12 months (technical visit is FOC) or paid visitation (RM65).    

You will receive appointment details via SMS within 48 hours.

You may proceed with the following troubleshooting steps and it shouldn't take you much longer than 15 minutes.

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN  cable to the Black port at D-Link Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://dlinkrouter.local./ and below  page will appear. (These are the defaults and if you have done a  configuration on your router previously, the password may be different)

Username: admin

Password: (Leave the field blank)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, click Settings and then choose Wireless.

6. Below screen will appear to configure the wireless setting. Since this is a dual band router, you will have 2 Wi-Fi Names (SSID); i.e. 2.4GHz and 5GHz.

i. For 2.4GHz setting, click Advanced Settings to display more available options.

ii. To change the channel, click the drop-down arrow for Wi-Fi Channel, then select your desired channel.

Choose between 1 to 13 (Suggested channels : 1,6,11). Click Save for the changes to take place.

The router will auto reboot and connection will re-establish after few minutes.

iii. Next, for 5GHz setting, click Advanced Settings to display more available options to make changes on the wireless channel for 5GHz.

iv. Click the drop-down arrow for Wi-Fi Channel, then select your desired channel from the selection.

v. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few  minutes.

Yes, customers will be charged 8% Service Tax for packages purchased after 29th February due to the implementation of the 8% Service Tax starting 1st March 2024.
 

Astro introduces Liga Malaysia for all Astro customers to watch the Malaysian Football League’s Liga Malaysia competitions LIVE, comprising Perlawanan Sumbangsih (Piala Sultan Haji Ahmad Shah), Liga Super, Piala FA and Piala Malaysia live in HD on Astro Arena (CH801), Arena Bola channels (CH803 and CH804) and stream on Astro GO until further notice.

Service Tax is charged based on the date the service is rendered. For services rendered on or after 1st March 2024, the Service Tax rate would be at 8% whilst for services enjoyed before 1st March 2024, the Service Tax rate would be 6%.
 

You may utilise your credit balance to offset future billing on your Astro account, or contact us here for further enquiries.

1. Router Positioning
   • Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
   • High vs. Low
     • Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals
     • ​Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for WiFi signals to penetrate.
   • Distance to Router
     • ​ The further away from your router you  get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
     • Otherwise, you should place your  router near the center of your home. After all, WiFi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.
2. Wireless Interference & Noise
   • You've probably never  noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices,  WiFi routers, satellites, cell towers, and more.
   • Although WiFi is  supposed to be on a different frequency than most of these devices, the  amount of radio noise can still cause interference. Some common causes of interference include:
     1. Microwaves
     2. Bluetooth Devices
     3. Cordless Phone
3. Surrounding Wi-Fi signals
   • A truth of the modern world is that every  household has their own WiFi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many  routers within close proximity.
   • Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels  for you automatically, but sometimes it's better to investigate and find the best channel yourself.
4. Usage
   • More likely, however, is that the people  on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/ Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

Starting 12 December 2023, Multiroom Smart TV app customers can enjoy two 4K Ultra HD (4K UHD) channels, namely CH549 Love Nature and CH805 Astro SuperSport. “Love Nature” is available to all customers regardless of their subscribed TV Pack. It celebrates the complexity of life on earth, presenting nature stories in stunning detail and colours.


Additionally, “Astro SuperSport” is only available to customers on the Sports, Sports Plus, Premium 1, Premium 2, Premium 4, Platinum Lite and Platinum Packs. This channel showcases a variety of sporting events, selected to appeal to the Malaysian viewing audience.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.        

‍

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Black port at D-Link Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.    

3. On the address bar, please go to http://dlinkrouter.local./ and below page will appear. (These are the defaults and if you have done a configuration on your router previously, the password may be different).          

Username: admin          

Password: (Leave the field blank)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, click Settings and then choose Wireless.

6. Below screen will appear to configure the wireless setting. Since this is a dual band router, you will have 2 Wi-Fi Names (SSID) i.e. 2.4GHz and 5GHz.

You may connect to any of the SSID, preferably with a stronger signal available.

7. You may change the Wi-Fi Name (SSID) and the Password to follow your preferences, and then click "Save" for the changes to take  place.

Please reconnect to the new wireless name with the new password once completed.

STEP 1  

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2  

Navigate to Settings.

STEP 3  

Navigate to STB Diagnostics and press "OK".

STEP 4    

Select Household Diagnostics and press "OK".

STEP 5    

Details information of Household Diagnostics screen will be  displayed.

For My Astro App Users 
Go to the "Account' tab and scroll to "Personal Info' section. Click "Name & contact info' to view and update your personal contact information.

For Ultra and/or Ulti Users 

1. Launch the My Astro app on your Home screen and you will land on your My Astro account dashboard. Then, press the yellow button on your Astro remote control to visit your "Account details".
2. Press the down button to view the "Personal info".
3. Press the left button and focus on the edit icon for the contact details, press on "OK" to change your contact details.

Astro GO is a companion app that is complimentary for all Astro subscribers and allows up to 2 users to stream at the same time. 200 hours of cloud recording* come complimentary with your Pay TV subscription. 

Astro GO+ is an add-on service that enables up to 4 users to stream Astro GO and/or Multiroom Smart TV** at the same time. The amount of cloud recording storage will also be increased to 1500 hours. 

 *Cloud recording hours are shared across your Astro Box, Astro GO and Multiroom Smart TV 

** Provided that you have a Multiroom Smart TV subscription

Step 1: You request for a move. 

‍
Step 2: One of our agents will contact you within 24 hours to set an appointment if you’re using Self Service - Astro Self-Service Portal.

‍
Step 3: You will receive a reminder of your appointment an hour before your scheduled time.

‍
Step 4: The technician will dismantle your satellite dish.

If there is no satellite dish, customers should dismantle the modem, router, and decoder by themselves.

‍
Step 5: You will need to transport your device(s) to your new home.

‍
Step 6: The technician will reinstall your satellite dish, (including modems and routers for broadband customers) at your new home based on the schedule appointment.

‍

Note For IPTV Customers:

1. Upon relocation request, all exiting IPTV customers will be converted to our Astro & Broadband service. Customers can choose to have standard Astro service with satellite dish, or unicast Plug & Play without satellite dish.

2. If customers choose to have satellite dish, an additional RM150.00 will be charged for satellite installation. If customers choose to have unicast Plug & Play service, no satellite dish is required, hence no extra charge will be incurred.

If Netflix is included as part of your Astro pack, you will find it in My Astro app 

where you will be able to manage all the streaming apps you are entitled to.  

Netflix will also be included in your Astro bill under “Monthly Charges”  

If you have added Netflix to your bill (Netflix Add-on), the Netflix subscription charge will appear in your Astro bill under “One-time charges” as Netflix App Subscription or Netflix Premium and will be charged monthly. You should refer to Netflix account Management for any changes to your Netflix subscription or should you wish to change to other billing methods.

Astro is continuously improving our user interface and introducing new features to our platforms to ensure that your Astro experience is more seamless, efficient and user-friendly.

For details on our latest interface, Picture-in-Picture mode and auto-start interactive mode on Astro GO, please click here.

In addition, we have also recently introduced a new look to the Title Information Page, the ability to disable the Profile Selection Screen and adjustable auto-standby timing. For more information, please click here.

1. Please standby computer/laptop to access to the internet and connection must be via LAN  (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and  direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.1.254 and below page will appear.

The default login of the router as below. If you have done a configuration on your router previously,  the password may be different.

Username: user
Password: Router S/N (Available on the sticker at the back of the router)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the left menu, choose Wireless 2.4GHz  and then click Basic Settings tab on the left menu to access to below screen.

6. You may change the Wireless Network Name (SSID) and the SSID Password to follow your preferences, then click "Save"  for the changes to take place.

Please reconnect to the new wireless name with the new password once completed.

7. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

You may change the Wireless Network Name (SSID) and the SSID Password to follow your preferences for 5GHz by choosing Wireless 5GHz  then click Basic Settings.

Click "Save" for the changes to take  place and reconnect to the new wireless name with the new password once  completed.