You can proceed with below troubleshooting if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4

Refer to the signal strength % shown on the top left of your screen.

If it is 65% or higher, please take the screenshot and submit your Feedback Form.

If it is below 65%, please go to Step 5.

STEP 5

Switch off the power for your box and make sure that the adapter’s power light is off.

‍STEP 6

Unscrew the satellite cable from the box and pull it out.

STEP 7

Plug the satellite cable back into the box and screw it back securely.

STEP 8

Switch on the power for your box and make sure that the adapter’s power light is on.

Please wait for 5 minutes.

STEP 9

Turn on your box. You should no longer be experiencing this issue.

‍

If issue persist, please submit the issue on our Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

‍

Centralized Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

Disabling band steering means that there will be two frequency bands available for the users - 2.4GHz and 5GHz.
 

Note: Band Steering is called Dual-band Combination in the router web interface.
 

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).
2. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user
Password: user
 

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi to configure the WiFi parameters.

6. Click on Dual-band Combination button to disable the Band Steering.

7. Set the Wi-Fi name and Wi-Fi Password for both 2.4GHz and 5GHz bands based on your preference. Then click "Apply" for the changes to take place.

8. Kindly ensure to reconnect your WiFi according your new WiFi name and password.

Customers with HD boxes can subscribe to the All-New Astro Pack without a box upgrade except if the customer request to move to OTT bundled pack which is mandatory to upgrade to Ulti or Ultra. 

Note: OTT is referring to either Netflix, D+H or both.

You may click here to Login and proceed to secure your Astro ID by linking it to your Astro account. If you do not have an Astro ID, please follow the steps in below to create one. You may also choose to log in or create Astro ID with your social accounts (eg. Facebook, Google and Apple).

Yes, the monthly subscription fee will be prorated into your Astro bill.

Yes, you are entitled to a free Ultra/Ulti box with free standard installation upon signing up Astro Fibre with a new 24-month contract.

Mac OS X

1. Click the Go tab in the top menu bar and select Utilities from the drop-down menu.

2. Type "network utility" in the search bar in the top right-hand corner of the Utilities window and then hit the "Enter" key on your keyboard. 

3. Click the Network Utility icon to open the Network Utility window.

4. For Ping Test, select the Ping tab and then type the address you'd like to ping in the text box. Click Ping and wait for the ping results.
 

5. For Traceroute Test, select the Traceroute tab and then type the address you like to traceroute in the text box. Click Trace and wait for the traceroute results.
 

Windows 10

1. Click the Search icon (magnifying glass) in the bottom left-hand corner and type "cmd" into the search bar.

2. Select the Command Prompt app - it will be at the top of the list of search results as the best match.

3. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

Windows 7 & Vista

1. Open the Start menu by clicking the Windows icon at the bottom left-hand corner of the screen.

2. Type "cmd" in the search bar at the  bottom of the menu.

3. Click cmd found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows 8

1. Move the mouse to the right-hand corner of the screen to make the vertical menu bar (charm bar) appear. Click Search.

2. Type "cmd" in the search bar and hit the Enter key on your keyboard.

3. Click cmd that found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows XP

1. Click the Start button in the bottom left-hand corner of the screen.

2. Click the Run option in the right-hand column.

3. Type "cmd" in the text box and then hit the Enter key on your keyboard.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you'd like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

Please visit any of Astro’s digital platform that you would like to log into, such as Astro’s official website (www.astro.com.my). Then, create a new Astro ID using your email address or mobile number by clicking “No Astro ID? Create Now!”. After creating your new Astro ID, please use it to log into our digital platforms moving forward.
 
If you have an active Astro subscription, you may also link it to your Astro ID. Please click here for the guide.
 

STEP 1
Switch off the power of your box and make sure that the adapter’s power light is off.


STEP 2
Unplug the HDMI cable from your TV and plug it back in securely to other available HDMI port.


STEP 3
Switch on the power for your box and make  sure that the adapter’s power light is on.
Please wait for 5 minutes.


STEP 4
Turn on your box. Do select the correct TV input.
You should no longer be experiencing this problem. 
​

Ultra Box with Contract:

Astro customers are entitled to a two (2) years manufacturer warranty and Installation warranty. During this period, after-sales service is free of charge. However, when your warranty period is over, all after-sales service is subject to a minimal service charge starting from RM65 inclusive of 8% Service Tax.

Other Decoders/Ultra Box Without contract:

Astro customers are entitled to a one (1) year manufacturer warranty and (6) months Installation warranty. During this period, after-sales service is free of charge. However, when your Installation warranty period is over, all after-sales service is subject to a minimal service charge starting fromRM65 inclusive of 8% service tax.

Yes, until 31 August 2022, customers can subscribe to the Movies Pack for only *RM59.99/month or the Platinum Pack for only *RM99.99/month for 6 months as well as the Premium 1 or Premium 3 Pack for only *RM99.99/month for 6 months until 30 October 2022 and be entitled to access Disney+ Hotstar as part of their Astro subscription. To find out more about our latest promotions, please visit promotions.astro.com.my. 

No, Ultra Box is only available for Entertainment Pack and above only.

The Multiroom (Smart TV) will mirror the subscription entitlement as per your primary subscription. However, NHK World, Radio, Sky News channels and 3rd party apps such as Netflix, Disney+ Hotstar are not available via the Multiroom (Smart TV).

The recommended home internet speed for a smooth viewing is 10Mbps.

The amount you're charged depends on:

• Your contract period and how long's left of your minimum term from the date your subscriptions end, calculated in months.
• Your current box type - Ultra or Ulti/Other Astro Boxes
• The packages you subscribe to, including App services such as Disney+ Hotstar and Netflix

We encourage customers to ensure their TV compatibility with the Astro Multiroom (Smart TV) app first before making any purchase here.

If you are still experiencing any issues, please contact us at wecare@astro.com.my or call or WhatsApp us at 03-9543 3838 and our agents will be happy to assist you.

You can add a reminder to pay your bill, on your Google Calendar with one click. Enjoy uninterrupted services, by remembering to pay your bill on time.

Please check SMS received on the unsuccessful payment status and should you require further clarification contact your issuing bank for clarification or contact us via WhatsApp.

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

You may access it by pressing "200' on your Astro remote control whilst watching TV.

STEP 1
Please wait while your Astro box initializes.



STEP 2
Select your preferred language.



STEP 3
Navigate to Next and press "OK".



STEP 4
Select Auto as the Video Resolution.



STEP 5
Navigate to Next and press "OK".



STEP 6
Navigate to Confirm and press "OK" to confirm your selection if you are able to read the texts on screen properly.
Otherwise, navigate to Cancel to revert to the previous settings.



STEP 7
Select Satellite as the box operating mode.



STEP 8
Navigate to Next and press "OK".



STEP 9
Select your preferred connection.
For connection via Wi-Fi, proceed to STEP 10.
For connection via LAN Cable, proceed to STEP 16 once you are connected.



STEP 10
Please wait while your Astro box searches for available Wi-Fi networks.



STEP 11
Navigate to your preferred Wi-Fi network and press "OK".



STEP 12
Please enter the password to connect to the Wi-Fi network.



STEP 13
Navigate to Done to continue.



STEP 14
Please wait while your Astro box connects to the internet.



STEP 15
Navigate to Yes to allow your Astro box to connect to this network automatically.
Otherwise, navigate to No.
Proceed to STEP 17 for the next step.



STEP 16
Navigate to Next and press "OK". 



STEP 17
Navigate to Universal.



STEP 18
Navigate to Next and press "OK".



STEP 19
Select 01 M3B VL - 10732 as the Entry Point.



STEP 20
Navigate to Next and press "OK".



STEP 21
Please wait until the signal reading is updated.
Navigate to Finish and press "OK" to complete the settings.

STEP 1
On your remote, press the Home button and the Home Page will be displayed your screen. 



STEP 2
Navigate to SETTINGS.



STEP 3
Navigate to Profile Selection on Startup and press “OK”.



STEP 4
Navigate to your preferred selection and press “OK”.



STEP 5
Navigate to Save and press “OK”.

For payments made using credit cards, refunds will be reversed back to the respective card. Whilst payment made by cash and online banking will be made to the account holders bank account.

You may submit your request via Feedback Form with below information details based on your payment method.

Please choose below option in the Feedback Form:

Category: I would like to request for refund

Sub Category: Request for Refund

1) Refund via Bank transfer:

Bank Name: 

Bank Account Number:

*Note: Please confirm your bank account details and ensure it's correct

‍

2) Refund via Foreign bank:

Bank Name:

Bank Account Number:

Bank Swift Code:

IBAN Code:

Currency: Eg: Dollar/Yen etc

*Note: Please confirm your bank account details and ensure it's correct

‍

3) Credit Card:

 Credit Card Number: 

ONLY last 4 digit credit card updated with Astro account

*Note: Please confirm your credit card details and ensure it's correct

Yes, you will enjoy an Ulti box when subscribing to Primary/Entertainment/ Movie Pack OR an Ultra box when subscribing to Sports/Sports+/Movies+/Premium 1/Premium 2/Premium 3/Platinum Pack.

You will get FREE installation for both Ultra/Ulti box upon signing up with Astro & Broadband.

Once your Plug & Play Box has been activated, a courier service will reach out to you within TWO (2) weeks for a time for them to pick up the old Astro box and SIM card/Smartcard.

1. Ensure that all cables have been plugged out of the old Astro box. To remove the white satellite cable from your old Astro box, simply hold the cable, twist, and gently pull.
2. Set aside these items to be ready for our delivery partner to pick up from you:

• Old Astro Box
• Old Astro Smartcard/SIM Card (leave this in your Astro Box)

3. When a courier arrives at your residence, do confirm that they are collecting items on behalf of Astro.
4. Allow the courier to check the serial number of the Astro box.
5. Hand them all the items for return, and you're done!

STEP 1    

On your remote, press the ... button and the Channel Guide page will be displayed on your screen.

STEP 2    

Select the channel you would like to remove as favourite and press "OK".

STEP 3  

Select "Remove from Favourite" and press "OK".

STEP 4    

You are successfully removed the channel from favourite list when this screen appears.

Yes, you will. Customers who purchased Astro First / Astro Best / Pay-per-View event in February 2024 with a viewing period in March 2024 will be charged an 8% Service Tax in their next bill.
 

Currently, there are no rebates provided when you sign-up for the Ultra/Ulti Plug & Play Box.

You can add a new Netflix account to your bill through CH 741 or clicking the Netflix button on the remote control. Please enter the email address you would like to use for Netflix subscription and ensure the Billing partner is Astro.  

If you would like to transfer your existing Netflix Account to be charged under Astro bill, please follow the steps below:  

1. Cancel your existing subscription with Netflix  

1. Once the remaining duration of your existing subscription has ended, you may proceed to subscribe for Netflix via Astro bill  

1. To subscribe, go to CH 741 and enter the email address used for your previous subscription with Netflix  

1. Once successfully completed, all existing settings and watching history on your Netflix account will be brought over  

You will be able to access Netflix on your Ultra and Ulti Box. However, kindly note that if you have an Ulti Box with a Netflix Premium subscription, you will not be able to watch content in 4K UHD and Netflix Spatial Audio.

Yes, you can upgrade your internet speed. However, speed downgrade is not allowed.

Please ensure to put your box on standby mode to refresh the signal.

a. Using IVR
   ​1. Dial 03-95433838 and select you preferred language.
   2. Select Account Related.

   4. Select Refresh Smartcard.

b. Using MyAstro web
  
STEP 1
Go to https://myastro.astro.com.my/ in your web browser.

STEP 2
Keyin your Email / Mobile number and password. Then, press "LOG IN".
 
STEP 3
Click on TV pack.
 

STEP 4
Choose Main Room for the Primary Box; else choose Multiroom (If any).
 

STEP 5
Click on "Refresh" to refresh signal on your box. 

For Main Box      

For Multiroom

STEP 6
After tap the Refresh, below notification will be displayed as below.

For Main Box 

For Multiroom

c. Using My Astro App

STEP 1
Open My Astro App and click "Login".

 

STEP 2
Keyin your Email / Mobile number and password. Then, press "LOG IN".

 

STEP 3
Go to "Account".

 

STEP 4
Scroll down to "TV pack" and click on it.

 

STEP 5
Choose Main Room for the Main Box; else choose Multiroom (If any).

 

STEP 6
Tap on "Refresh" to refresh signal on your box. 

 

STEP 7
After tap the Refresh, below notification will be displayed as below.

 

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the blue port in Cisco Router and direct to computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

‍

‍

4. Type the Username and Password as below. Then click "OK". (These are the defaults, if you have done previous configuration on your router the password may be different).

Username: admin

Password: admin (or time123)

5. Click "OK" when a Warning prompt that says,” Using this advanced utility to change your router settings could disable your network” appears. Below display will appears.

6. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

7. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

8. Click Wireless Security to view the security settings of your wireless network. Take note of the Security Mode and the Passphrase.

For the example below, the Security Mode used is WPA2/WPA Mixed Mode.

The Wireless name is called Network Name (SSID) and the Passphrase is your wireless password.

‍

9. Now that you have the Wireless name and Password, you are ready to connect your wireless computers and devices to the network.

10. You may change the Network Name (SSID) and the Passphrase to follow your preferences and please ensure save the changes made. Please reconnect to the new wireless name with the new password once completed.

‍

You may manage all your Astro subscriptions via My Astro app. Download here or on your App Store or Google Play Store.

Netflix is a streaming entertainment service that offers a wide variety of award-winning TV programmes, films, anime, documentaries and more - on thousands of internet-connected devices. There's always something new to discover, and more TV shows and movies are added every month. The more you watch, the better Netflix gets at recommending TV shows and movies you'll love.

Astro customers with an internet-connected Ultra Box or Ulti Box can access the Netflix app and watch Netflix content via their Astro Box. For more information about Netflix, visit the Netflix website.