The minimum internet speed required to stream via Ultra Plug & Play Box is 30Mbps for 4K UHD viewing, and Ultra/Ulti Plug & Play is 10Mbps for HD viewing. For better streaming experience, we recommend 100Mbps and above.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

Please contact us through one of our platforms found here or Self-serve by logging in to Astro Self-Service Portal within 3-7 days before moving out and we will sort everything out for you!

Astro sends regular payment reminders to customers via SMS until their current charges have been paid. However, we encourage customers to pay their bill as soon as possible to avoid disconnection of Astro service. Please reach out to us here if you require more information about payment reminders or to change your contact details.

For all new Astro Fibre customers with the RG21 router, the Astro Fibre App will be installed on your mobile device for you during installation. Alternatively,you may refer to the user guide here for self-installation.

Payment via cheque will take 3 - 5 working days to be posted. If you require faster payment posting, we recommend you to pay online via Astro Quick Pay.

Currently Astro GO is only available in Malaysia. You will not be able to access it if you are overseas.

The default PIN is 0000. You may change your PIN to a secure one by doing this at Settings, under your Preferences, select PIN Management, enter your old PIN or default PIN and proceed to create a new PIN.

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2  

Navigate to Settings.

STEP 3  

Navigate to S/PDIF Audio and press "OK".

‍

STEP 4    

Navigate to your preferred selection and press “OK”.

You have exceeded the maximum number of registered devices allowed. To manage devices on Astro GO, go to Settings > Registered Devices to view / remove devices from the list of registered devices to your account.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.
 

No, you are still able to subscribe to iQIYI on your current Astro pack.

Your bill will be waived upon request.

Step 1: Download the My Astro app from either the App Store, Google Play or HUAWEI AppGallery.

Step 2: Sign in with your Astro ID.

Step 3: Select "Rewards" on the home screen to get started.

Watch this tutorial to learn how to create your Astro ID.

This exercise currently only affects person-to-person SMS with URL links. However, the blocking of SMS sent by businesses via short codes such as 6XXXX, 3XXXX, 2XXXX and 1XXXX will be implemented at a later phase. In response to this government initiative, Astro customers will no longer receive SMS bills effective 1 August 2023. This change will be carried out in phases.  

Please switch your preferred Bill Delivery Method using our self-service portals via My Astro Web or My Astro app. Please click here to download the app on your mobile device or login to My Astro Web.

For customers with the Ultra or Ulti Box, you are required to return only the Astro box along with the Smart/SIM Card. There  is no requirement to return the remote control, power cables or satellite  dish/outdoor unit (ODU).

For customers on other Boxes, you are required to discard them (and their accompanying devices such as the Smart/SIM Card) only at registered collection centers for proper handling and management of e-waste in an environmentally sound manner. Click here to find a registered collection center near you.

·      Bill 

·      Log into your Astro Self-Service (location)

·      WhatsApp

Yes, existing Astro & Broadband customers within contract or out of contract can subscribe to Astro Fibre Bundle. The 24-month contract will be renewed.

However, your contract with Maxis/Allo needs to be terminated before signing up to this offer. An early cancellation fee applies if you are still within contract.

‍*Subject to Terms &Conditions of your contract

Please make sure that:

1. You are logging in with the correct registered Astro ID (email or phone number) and password. If you can’t remember your password, please proceed to use the “forget password” function.
2. You have an Astro ID that is linked to an Astro account. (note: NJOI – linked users will not be able to log into Astro GO)
3. Your Astro account is active and not under suspension.

If the above points have been met, you may try some quick solutions below:

1. Clear the cache on your browser or app.
2. Check if you have the latest version of the browser or app.
3. Log out and log back into the browser or app.
4. Relaunch the browser or app.
5. Restart your mobile device.
6. Restart your internet connection.

All existing or new Astro customers who meet the following criteria may upgrade to the Ultra Box:

1. Have an internet connection at home (recommended>10Mbps speed)
2. Maintain a minimum subscription with a HD + Recording service

If you live in a high-rise building, please call us at 03- 7481 8000 to check if your building can support the Ultra Box. If your high-rise building allows for the set-up of individual dishes you will be able to upgrade to the Ultra Box, subject to the criteria above.

If you would like to access our 4K UHD content via the Astro UHD channel 805 and UHD content on VOD, Astro Best and Astro First. We also recommend:

1. 4K UHD supported TV that is HDCP2.2 compliant
2. Internet connection of at least 30Mbps

Note: If you do not have an internet connection at home, you may take up the Ultra Box bundled with Astro™'s broadband package with rebates of up to RM30/month. For more details and to sign up for Astro & Broadband, please click here.

Deposit of RM500 (Maxis) and RM300 (Allo) is payable by new subscribers (non-Malaysian). The fee will be reimbursed when service is terminated.

No deposit required for all existing Astro customers and new subscribers (Malaysian).

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to SETTINGS and press "OK".

STEP 3

Navigate to STB Diagnostics and press "OK".

STEP 4

Navigate to Network Diagnostics and press "OK" .

STEP 5

Please ensure the Tunes service multicast status is Multicast Up.

If the status is Multicast is Not Available, please reboot the decoder and router before verifying this status.

If issue persists, please submit the issue on our Feedback Form with error details and attach a picture of your Network Diagnostics.

Step 1:
Type ASTRO<space>BAL<space>10-Digit Astro Account No. 
Example: ASTRO BAL 08XXXXXXXX

*Standard telco charges and Terms and Conditions apply

Step 2:
Send SMS to 66688

Yes. You are entitled to separate Netflix accounts for each main Astro subscription e.g. If you have subscribed to Entertainment Plus, Platinum Pack, etc separately. Therefore, if you have more than one main Astro subscription with Netflix, you may choose to create multiple email addresses to activate each respective Netflix subscription. Please follow the steps provided to you via email/SMS in order to activate your Netflix subscriptions on the website.

Yes, customers may need to provide additional documents such as bank-in slips or payment receipts. Any incomplete document, customer will be notified by Astro after validation is made.

If you choose to self-install the Plug& Play Box, then no installation fee will be charged. However, there will be an activation fee (please refer to the table below)

If you choose to have an installer to install the Plug & Play Box, then an installation fee will also apply.

Astro is continuously improving our user interface and introducing new features to our platforms to ensure that your Astro experience is more seamless, efficient and user-friendly.

For details on our latest interface, Picture-in-Picture mode and auto-start interactive mode on Astro GO, please click here. For enhancements to the Title Information Page, the ability to disable the Profile Selection Screen and adjustable auto-standby timing, please click here.

In addition, we have also recently introduced an infinite scrolling feature at the title information page and the ability to select the video quality directly from the video player. For more information, please click here.

Tune to channel 200 - select on "My Account".Your Total amount due will be stated under the "Bill Summary" section.

**Please note that this feature requires your box to be connected to your home Wi-Fi. Alternatively you can perform the SMS steps displayed on the screen to check your bill amount.

Each Astro customer is entitled up to 4 smart devices to be registered including mobile, laptops, tablets and Smart TV per household.

If you have maximised the registered device, you will be able to see the list of all your current registered devices on your mobile screen. Please remove any one device to allow the current Smart TV device to be included.

Do note that only 1 Smart TV device is allowed at any point in time.

Please check your internet speed and connection status via internet connection test. If your internet is working fine and the issue persists, proceed to submit report via WhatsApp or Feedback Form.

STEP 1    

On your remote, press the HOME button.

‍

STEP 2    

Navigate to Update Satellite Frequency and press “OK”.

‍

STEP 3  

Choose Test Satellite Frequency and press “OK”.

‍

STEP 4  

Select Yes, continue and press "OK" to start the test.    

Otherwise, select No, go back to cancel.

‍

STEP 5    

Satellite Frequency Test progress screen will be displayed.

‍

STEP 6    

The test result will be displayed once completed.    

Press "OK" to go back to channel.

STEP 1    

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Take a look at the HDMI Connection Status.

You will be charged 8% Service Tax on Astro Pay TV services rendered on or after 1st March 2024, whereas your Astro Fibre including Mesh will remain at 6% Service Tax.
 

There will be no penalty imposed upon the removal of Astro GO+ from your subscription.

This issue occurs because  your TV does not support the higher resolution.
 

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.
 

STEP 2

Switch on the power for your box and make sure that the adapter's power light is on.
 

STEP 3

Press the standby button repeatedly after switch on the power.

The Startup Options screen will appear on your TV.

STEP 4

Press "987" to access the Advanced Startup Options menu.

Then, press "1" to initiate a reset setting.

STEP 5

Press "OK" to confirm restore to factory setting.

STEP 6

After the factory setting is restored, TV will turn blank.

Please wait until the box completes initiate setup.

STEP 7

Press "1" to initiate Linux download on the software.

STEP 8

Once completed, the following screen will appear on your TV.

Refer to Installation Setup guide here to complete the setup.

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which could  cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

STEP 1

Try to change channels on your Astro remote. Check the LED light.
If the LED is blinking 3 times or if it is not blinking, replace the batteries and proceed to STEP 2.
Otherwise, if the LED is blinking 1 time, your remote is working fine, let's proceed to STEP 3.

STEP 2

Check if you can change channels using your Astro remote control. You should no longer be experiencing this problem if is a battery issue.
If issue remain after batteries replacement, proceed to STEP 3.

STEP 3

You need to refresh the box setting manually from the box front panel.
Refer to Refresh Box setting (Clear NVRAM) - Ultra / Ulti Box. 
If issue persist, please submit the issue on our Feedback Form.
 

Step 1: You request for a move. 

‍
Step 2: One of our agents will contact you within 24 hours to set an appointment if you’re using Self Service - Astro Self-Service Portal.

‍
Step 3: You will receive a reminder of your appointment an hour before your scheduled time.

‍
Step 4: The technician will dismantle your satellite dish.

If there is no satellite dish, customers should dismantle the modem, router, and decoder by themselves.

‍
Step 5: You will need to transport your device(s) to your new home.

‍
Step 6: The technician will reinstall your satellite dish, (including modems and routers for broadband customers) at your new home based on the schedule appointment.

‍

Note For IPTV Customers:

1. Upon relocation request, all exiting IPTV customers will be converted to our Astro & Broadband service. Customers can choose to have standard Astro service with satellite dish, or unicast Plug & Play without satellite dish.

2. If customers choose to have satellite dish, an additional RM150.00 will be charged for satellite installation. If customers choose to have unicast Plug & Play service, no satellite dish is required, hence no extra charge will be incurred.

Mac OS X

1. Click the Go tab in the top menu bar and select Utilities from the drop-down menu.

2. Type "network utility" in the search bar in the top right-hand corner of the Utilities window and then hit the "Enter" key on your keyboard. 

3. Click the Network Utility icon to open the Network Utility window.

4. For Ping Test, select the Ping tab and then type the address you'd like to ping in the text box. Click Ping and wait for the ping results.
 

5. For Traceroute Test, select the Traceroute tab and then type the address you like to traceroute in the text box. Click Trace and wait for the traceroute results.
 

Windows 10

1. Click the Search icon (magnifying glass) in the bottom left-hand corner and type "cmd" into the search bar.

2. Select the Command Prompt app - it will be at the top of the list of search results as the best match.

3. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

Windows 7 & Vista

1. Open the Start menu by clicking the Windows icon at the bottom left-hand corner of the screen.

2. Type "cmd" in the search bar at the  bottom of the menu.

3. Click cmd found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows 8

1. Move the mouse to the right-hand corner of the screen to make the vertical menu bar (charm bar) appear. Click Search.

2. Type "cmd" in the search bar and hit the Enter key on your keyboard.

3. Click cmd that found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows XP

1. Click the Start button in the bottom left-hand corner of the screen.

2. Click the Run option in the right-hand column.

3. Type "cmd" in the text box and then hit the Enter key on your keyboard.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you'd like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

There are 2 methods of setting maturity ratings restriction on Netflix: 

‍

Method 1 – Create a Kids Profile in Netflix App on Ultra/Ulti Box 

1. On the Netflix home menu, select “Switch Profile” 

2. Select Add Profile.  

3. Name the profile. 

4. Select Kids. Kids profiles have a logo 'Kids' on the profile icon so they are easy to identify.  

5. Select Continue. The new profile will show on the list of profiles on your account. 

‍

Method 2 – Manually set Viewing Restrictions for each profile 

1. Go to https://www.netflix.com/profiles/manage

2. Select a Profile. 

3. Under Maturity Settings, select Edit. 

4. Enter your Netflix password. 

5. You may select the desired Maturity Rating settings or add a particular title restrictions for the profile. 

6. Select Save. 

For more information kindly visit: 

• https://help.netflix.com/en/node/114275

• https://help.netflix.com/en/node/114276

Please check if you are streaming on a supported device. Astro GO is only applicable within the supported platforms; mobile devices (phones and tablets) and web browsers.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.

Please follow the steps below to retrieve your Astro ID:



Note: Only Astro customers whose Astro ID is linked to their subscription can retrieve their Astro ID this way. Otherwise, you would need to create a new account.
 

It will take around 10 to 15 minutes before you are able to view your purchase.

1. Power reset (on & off) your Modem and Router.

2. Ensure standard physical connection (No 3rd party devices connected to decoder and modem).

3. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

4. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

5. On the address bar, type https://testmyline.astro.com.my/ and below page will appear.

6.Click "GO", and the test will begin.

The test is completed once both download and upload speeds are displayed.

Sample of the Speedtest result is shown below.

**Please ensure the snapshot includes a time stamp and network used either LAN cable or wireless (as per picture above)

7. Kindly screenshot or take a picture of the result, name it as "LAN Speedtest" for test using LAN cable (wired connection).

8. Repeat the test once again using WiFi connection (Please unplug your LAN cable and connect via wireless connection using your SSID).

9. Screenshot or take a picture of the result, name it as "WiFi Speedtest".

No, there are no penalty fees for the Mesh WiFi devices should you wish to terminate Astro Fibre within/after 24 months. 

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which could cause the issue.

3. If issue persists, submit your Feedback Form for further assistance.

Currently, My Astro app and web supports TV pack upgrade. You can go to "Account' and scroll to  "Subscription' section and select "TV pack'. You may reach out to us via WhatsApp at 03-9543 3838 for more details.

For Ultra and/or Ulti box users, launch the My Astro app on your Home screen and you will land on the My Astro account dashboard. Press ">'  remote button to go to your Subscription card and "OK' button to proceed with the TV pack upgrade.

Astro TV customers

No, you will not be required to take on a new contract after moving. If you still have an existing contract, the contract will continue.

‍

Broadband / IPTV customers

Yes, your contract will be renewed to a new 24-month contract.

(i) Head over to My Astro Portal and go to 'Bill & Payment'. Click on 'Payment History'
(ii) Contact us via one of these platforms. Please ensure you include your Astro Account Number.

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3  

Navigate to Satellite Settings and press "OK".

STEP 4  

Select Diagnostics and press "OK".

STEP 5    

Signal reading on Tuner 1 will be displayed. Navigate to right arrow for next step.

STEP 6  

Signal reading on Tuner 2 will be displayed. Navigate to "Done" and press "OK" to complete the diagnostics.