STEP 1
Check the internet connectivity by run the Test Connection.
Refer Run Test Connection.


STEP 2
Verify the average speedtest based on the Test Connection result.
a. Above 10Mbps - Proceed to STEP 5
b. Less then 10 Mbps - Proceed to STEP 3

Notes: Minimum 10 Mbps internet speed from box requires in order to get a stable connection.



STEP 3
Check the connection to the box either using Ethernet (LAN cable) or Wi-Fi.
a. If using Ethernet (LAN cable) - Connect to Live Agent for help.
b. If using Wi-Fi - Proceed to STEP 4



STEP 4
Check location of the decoder and router.
a. If nearby (within 1.5m) - Try connect to box from router using LAN cable.
b. If far (more than 1.5m) / No LAN cable - Proceed STEP 5



STEP 5
Reboot router, modem and decoder.
If issue persist, please try again after 30mins to 1 hour. Connect to live agent if persist after 30 mins to 1 hour.

Yes, existing non-Primary Pack customers who add on 50Mbps to their subscription will get to enjoy high speed broadband for only RM60/month and a free speed upgrade to 100Mbps for 24 months. Please note that a new 24-month contract will start upon successful installation.

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.
2. Ensure the fiber cable from your wall socket and modem is securely connected.

Notes: You might be connected to LAN 1 if backbone is Maxis

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option  2/ Option 3/ Option 5/ Option 6

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.    

2. Ensure the fiber cable from your wall socket and modem is securely connected.

3. Ensure both cables on the Modem (LAN Port 2) and Router (WAN Port - Red port) are properly connected.

Notes: You might be connected to LAN 1  if backbone is Maxis
 

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. Please make sure both cables on Router (Any Yellow port) and Astro Decoder (Network Port behind decoder) are properly inserted.

5. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

6. If the issue persists, submit your feedback form and attach your modem light indicator picture/ video for further assistance.
 

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

Video On Demand (VOD) is a new way of enjoying your Astro, for free* as part of your subscription. Here's what you can do by watching your show via VOD:

1. Pick and choose your show anytime of the day without needing to wait for your show to air.

2. Catch-up on episodes you've missed or binge-watch all episodes instantly.

3. Pause, rewind, or fast-forward to your favourite parts of the show.

4. Watch full uncut episodes.

5. No weather or other disruptions during your viewing time.

6. Browse our library of recommended shows for you based on your viewing history. Everything you see is free as part of your subscription.

7. To rent additional blockbuster movies on a pay-per-view basis, visit the "Store' section in our VOD library.

Here’s how to access On Demand:

1. Connect your Astro PVR/Ultra Box to Wi-Fi or download the Astro GO app from here.

2. Press Home on your remote and scroll to On Demand or login with your Astro ID via your Astro GO app.

3. Start streaming on your TV or Astro GO app anytime, anywhere.

* On Demand is FREE for customers with a Wi-Fi connected PVR/Ultra Box and Astro GO app. Entitlement is based on your subscription.

Note: You can also rent additional movies on a pay-per-view basis, all found in the Store.

Returning your Astro box & Smart card/SIM card is a very simple process.

For existing Ultra Box or Ulti Box user, call 03-9543 3838 to schedule our courier partner to come pick up the box or drop them off at the closest Astro Service Centre or Exclusive Partner near you. Click here to find a Customer Service Centre (CSC) or Astro Exclusive Partner (AEP) near you.

For any unreturned Ultra Box or Ulti Box, a box fee of RM100 may be charged to your account.

For all other boxes, please recycle your box at a registered collection center that will properly manage the boxes in an environmentally friendly way. Click here to find a registered collection center near you.

If you would like to upgrade your pack to include Disney+ Hotstar Premium, please contact Astro Customer Contact Centre at 03 9543 3838. Alternatively, please WhatsApp Astro at 03 9543 3838 and type DH Help for further assistance. 

Mesh WiFi devices are available as an add-on subscription from RM10/month across all Astro Fibre speeds. You may subscribe to a maximum of 5 units of Mesh WiFi per Astro Fibre subscription. 

You can contact Astro's Contact Centre (03 - 9543 1543) to subscribe to the Mesh WiFi.

Not to worry, you will only need to verify your Astro ID once. After that, you may log in to your account as usual.

Please refer to these FAQs for more information.

Starting 12 December 2023, Multiroom Smart TV app customers can enjoy two 4K Ultra HD (4K UHD) channels, namely CH549 Love Nature and CH805 Astro SuperSport. “Love Nature” is available to all customers regardless of their subscribed TV Pack. It celebrates the complexity of life on earth, presenting nature stories in stunning detail and colours.


Additionally, “Astro SuperSport” is only available to customers on the Sports, Sports Plus, Premium 1, Premium 2, Premium 4, Platinum Lite and Platinum Packs. This channel showcases a variety of sporting events, selected to appeal to the Malaysian viewing audience.

You can request for a password reset by clicking on "Forgot My Password' at the login page.

Your monthly bill of the previous and new pack will be prorated. This will be reflected into your bill accordingly.

STEP 1    

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Take a look at the Smart Card Status.

Your account number will be used to identify/verify you for all After Sales-Services. You may also use your mobile number/ Astro smart card number/ NRIC number or Astro Box number.

Please refer to these FAQs and Terms and Conditions for more information.

For more support and options for your subscription, please WhatsApp us at 03 9543 3838 and type DH Help. Alternatively, you may visit astro.com.my/Disney for more information.

Upon successful subscription, you will be able to view your chosen HD channels within 3 hours by keying in the channel numbers into your remote control. Please note that subscription through Channel 200 will take effect within 24 hours.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

‍

STEP 2

Navigate to Settings.

STEP 3

Navigate to Menu Language and press "OK".

STEP 4

Navigate to your preferred language selection and press “OK”.

Any Astro GO compatible device (mobile/tablet/PC) and Multiroom Smart TV* compatible TVs will benefit from Astro GO+. 

1. Clearly indicate full name of Astro customer, contact number and Astro subscription account number when making each payment (e.g. on bank-in slips)
2. For Direct Debit, please contact your bank for standing instructions. Provide the full name of Astro customer and Astro account number. The Direct Debit service may not be available with all banks. Please check with your bank for confirmation of Direct Debit service.
3. Please inform us of any changes in billing address/information by contacting us via one of these platforms.

IMPORTANT NOTICE: To avoid any problems in payment processing, please pay only at authorised Astro payment channels

1. For WiFi connection:
   • For Internet speeds up to 300Mbps, the user needs to have minimum WiFi 802.11n (5GHz) capabilities
   • For Internet speeds up to 500Mbps, the user needs to have minimum WiFi 802.11ac (5GHz) capabilities
   • For Internet speeds up to 800Mbps, the user needs to have minimum WiFi 802.11ax (5GHz) capabilities
2. ​For Wired connection:
   • The users need to use Cat5e Network cable or better and have their device equipped with 1Gbit Network Interface Card (NIC)
3. A summary of the minimum specifications for devices as tabulated below:

1. Number of WiFi antennas in the client device
2. Distance and WiFi signal strength between client device and RGW/Mesh AP
3. Overall WiFi signal congestion/pollution in area
4. Total number of devices connected to the RGW/Mesh AP

• Distance from the RGW/Mesh AP
• Client's Wi-Fi hardware specifications/capabilities
• Overall Wi-Fi signal quality in the area

You will be able to view your new package(s) within 24 hours of subscribing. Please note that if you are an Astro customer subscribing to HD channels, you will have to connect an HDMI cable to your TV before you will be able to enjoy the channels.

The different light colours on your Astro Ultra Box or Ulti Box informs you on the phase the box is going through.

‍

1. Ultra Box magenta light / Ulti Box purple light - Your box is turned "On". ‍

Press the Home button to launch Video On Demand and stream anytime or press channel number on your remote.

‍

2. Ultra Box / Ulti Box orange light - Your box is on "Standby" mode.

Your box is ready to be turned "On" or leave it in this mode to receive new software updates.

3. Ultra Box / Ulti Box blinking orange light - Your box is booting up.

Please wait a few minutes for the box to start.

‍

4. Ultra Box / Ulti box blinking blue light - Your box is downloading a software update.

Please wait a few minutes for the download to complete.

All Astro customers and non-customers who have an Astro ID will no longer be able to log in to our digital platforms using their usernames. Users will experience this change if they currently do not use an email address or mobile number to login, for example: johndoe2023.

When Band Steering is enabled, only one SSID network name with one password is available. Example:

i.SSID: SSID, Password: 12345678

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please ensure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Intermittent internet connection using Wi-Fi
1. Router Positioning

Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day  and night.

  i) High vs. Low

     Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.

  ii) Concrete & Metals

      Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also,       avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which       can be almost impossible for Wi-Fi signals to penetrate.

  iii) Distance to Router

      The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.

Otherwise, you should place your  router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.

2. Wireless Interference & Noise

You've probably never  noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices,  Wi-Fi routers, satellites, cell towers, and more.

Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:

i) Microwaves
ii) Bluetooth Devices
iii) Cordless Phone

3.  Surrounding Wi-Fi signals

A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially  problematic in housing complexes and apartments where there can be many routers within close proximity.

Which is why it's important that you pick  a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

4. Usage

More likely, however, is that the people  on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/ Netflix.

Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in  your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document,  PDF, Image file) before submitting the form.

Quick Info
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

Please update your auto-debit payment details via My Astro Portal.

Real-time payments are posted almost instantaneously. However, daily system maintenance occurs between 12AM to 3AM - any payment made during this period will be delayed until system maintenance is complete.

Astro is continuously improving our user interface and introducing new features to our platforms to ensure that your Astro experience is more seamless, efficient and user-friendly.

For details on our latest interface, Picture-in-Picture mode and auto-start interactive mode on Astro GO, please click here. For enhancements to the Title Information Page, the ability to disable the Profile Selection Screen and adjustable auto-standby timing, please click here.

In addition, we have also recently introduced an infinite scrolling feature at the title information page and the ability to select the video quality directly from the video player. For more information, please click here.

STEP 1    

Check your current software version on your box.

If the software version updated (Refer to Table 1) , proceed to STEP 2.

If software version different from Table 1, click here for Software Update guide.

Once software is updated, tune to the impacted channel.        

If issue persist, proceed to STEP 2.

‍

STEP 2  

Run Test Satellite Frequency.    

Click here for the guide.

‍

If dCSS Scan Entrypoint Success, proceed to submit report here.

Guide to submit report:    

At Feedback Type select "I have Astro service related question/request" and Sub Category as "Technical Interruption".

Fill up all the required information and submit.    

Please indicate if you agreed  to recontract for 12 months (technical visit is FOC) or paid visitation (RM65).    

You will receive appointment details via SMS within 48 hours.

If dCSS Scan Entrypoint Fail, proceed to STEP 3.

‍

‍STEP 3    

Proceed to Update Satellite Frequency.

Click here for the guide.
Once completed, tune to the impacted channel.

If issue persist, proceed to submit report here.

‍

Guide to submit report:    

At Feedback Type select "I have Astro service related question/request" and Sub Category as "Technical Interruption".

Fill up all the required information and submit.    

Please indicate if you agreed to recontract for 12 months (technical visit is FOC) or paid visitation (RM65).    

You will receive appointment details via SMS within 48 hours.

Yes, if a device is faulty due to customer's negligence, it is subject to a penalty fee for each device:

• WiFi router: RM200

• Fibre modem: RM500

• Mesh WiFi: RM200/unit

Step 1: Separate Your Wi-Fi Network Name

First, you need to set up your Wi-Fi to Dual-band in order to be less susceptible to interference, and allows you to choose between the 2.4GHz or 5GHz bands when connecting a device. A Wi-Fi frequency of 5GHz is best when you are near your router, and 2.4GHz is best for when you are far from your router.

• Check the bottom of your router for a website or IP address, username, and password.

Below are details for a standard login based on a standard router issued by ISP (Telekom Malaysia, Maxis, and Time dot Com)

• Login to your account
• Identify your Wi-fi Settings (This could be in advanced settings)
• Identify both the 2.4GHz and 5GHz options.
• Split the signals by renaming the 2.4GHz and 5GHz signals respectively, and make sure both are enabled.
• For detailed instructions based on router model, on how to separate your Wi-Fi, click here and choose the option according to your ISP and router brand.

Step 2: Factory reset your Ultra Box by following the steps below.

a. Press the Home button on your remote

b. Go to your settings page

c. Scroll down and select Reset/Restore

d. Select restore factory settings and proceed

e. Enter your PIN to access restore factory settings (default pin: 0000)

f. Choose restore and wait until the box reboots automatically. This may take around 2 minutes and you will see the Astro logo again when it's done.

The Astro Fibre app is a newly introduced mobile application exclusively for Astro Fibre customers to allow them to schedule when each user can access the internet, share network access to guests in a secure manner, easy device management, amongst many other features for a better WiFi experience. For more information about this app, please visit here.

If you accidently clicked “delete my account” on the Astro Fibre app, you will bedirected to submit a request via Feedback Form as the image below.

If you submit a request, our Astro representative will get back to you within 3 business days to learn more about the issue(s) you are currently facing with the app. Customers may proceed to permanently delete their account during the call if they wish. Once complete, your Astro ID will be deleted and you will be unlinked from all Astro apps and services including partner apps that are associated with your Astro ID including Astro GO, My Astro, Astro Awani, Syok, beIN SPORTS CONNECT, iQIYI, TVBAnywhere+,HBO GO, Gempak, XUAN, Astro Ulagam etc.

You may create another Astro ID by following the steps here and re-link your new account to all Astro apps and services, including partner apps.

Please follow the steps below:

Step1: Fill in Merge/Split Equipment Form (Part A & Part B)

Step2: A full payment to be made on any outstanding balance for all related accounts (if any).

Step3: Submit all documents via feedback form or walk in to nearest Astro Customer Service Centre (CSC).

Step4: Customer will expect a call from our validation team (Note: Turnaround time for merge/ split of account is 3-5 working days upon receiving all complete documentation).

Note:

1. There might be a loss of transmission during the processing of transfer equipment ownership, split or merge of equipment.

You may click here to Login and proceed to secure your Astro ID by linking it to your Astro account. If you do not have an Astro ID, please follow the steps in below to create one. You may also choose to log in or create Astro ID with your social accounts (eg. Facebook, Google and Apple).

Connect your PVR to Wi-Fi and enjoy access to our library of Video On Demand. Replay old seasons, catch-up latest episodes of your favourite shows, anytime you want. To connect your PVR, follow the steps below depending on your box type:

(a) Wi-Fi Enabled PVR (DMT5)

·      Press the “Home” button and select “Settings” > “Network” > “Wi-Fi”

·      Allow the PVR to scan Wi-Fi networks available and subsequently choose your home Wi-Fi network > Enter your Wi-Fi password if required

·      Once connected, the icon below will appear on the screen.

‍
      Tip: Use the alpha-numeric keyboard on your Astro Remote to key in your password

·      Press the “Home” button and select “On Demand” to start watching videos on demand!

‍

(b) Non-Wi-Fi Enabled PVR (HD PVR)

There are two ways to connect your HD PVR decoder to your home Wi-Fi
(i) Using the Ethernet (LAN) cable 
 

·       Plug in the LAN cable from your modem into the PVR network port

·       Once connected, the icon below will appear on the screen

·       Press the “Home” button and select “On Demand” to start watching videos on demand!

(ii) Using an Astro Wi-Fi dongle as per shown below

Step 1 - Plugin the Wi-Fi dongle into the front USB part of your PVR decoder.

Step 2 - A prompt will appear stating "Do you wish to connect to a wireless network?", select "Yes, continue."

Step 3 - Once connected, the Wi-Fi icon will appear on the screen. Now you are ready to download and enjoy Astro's on demand entertainment.

Step 4 - Press the “Home” button and select “On Demand” to start watching videos on demand!

*The Wi-Fi dongle is only applicable for the non-Wi-Fi enabled PVR (as per the picture).