If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.
 

1. Try loading the site on a different device.
   • Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.
   • If the website doesn't load on another device, the problem is either with the network
2. Restart your computer.
   • Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.
3. Try loading the site in a different browser.
   • There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.
4. Temporarily disable your antivirus program.
   • Your antivirus software may be interfering with your ability to load certain websites.
   • Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.
5. Reset  your modem and router.
   • Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.
6. Check your computer's date and time settings.
   • If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.
   • Check your computer or mobile device's clock to make sure that it is set to the correct time and date.

i. List of websites effected.
ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.  
iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.
iv. Run the Ping Test -  Please click here for Ping Test guideline.

Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.    
A Traceroute Test traces the route of packets to destination host from our  server.

STEP 1

Try to change channels on your Astro remote. Check the LED light.
If the LED is blinking 3 times or if it is not blinking, replace the batteries and proceed to STEP 2.
Otherwise, if the LED is blinking 1 time, your remote is working fine, let's proceed to STEP 3.

STEP 2

Check if you can change channels using your Astro remote control. You should no longer be experiencing this problem if is a battery issue.
If issue remain after batteries replacement, proceed to STEP 3.

STEP 3

You need to refresh the box setting manually from the box front panel.
Refer to Refresh Box setting (Clear NVRAM) - Ultra / Ulti Box. 
If issue persist, please submit the issue on our Feedback Form.
 

Your cloud recording space will revert to 200 hours by default. If your current recordings exceed 200 hours, the system will delete the exceeded hours once you have stopped the Astro GO+ subscription starting with the oldest recordings first.

You can add a new Netflix account to your bill through CH 741 or clicking the Netflix button on the remote control. Please enter the email address you would like to use for Netflix subscription and ensure the Billing partner is Astro.  

If you would like to transfer your existing Netflix Account to be charged under Astro bill, please follow the steps below:  

1. Cancel your existing subscription with Netflix  

1. Once the remaining duration of your existing subscription has ended, you may proceed to subscribe for Netflix via Astro bill  

1. To subscribe, go to CH 741 and enter the email address used for your previous subscription with Netflix  

1. Once successfully completed, all existing settings and watching history on your Netflix account will be brought over  

Yes. Astro customers will soon be able to enjoy seamless access to Netflix on their connected Ultra and Ulti Boxes. Look out for more details then! Register your interest via https://astro.com.my/Netflix

Your purchase will be reflected on your next monthly Astro bill. For example, if you rented a movie for RM 15.00 for 2 days and your next bill statement is in 2 weeks. RM 15.00 will be reflected in your Astro subscription bill in two weeks' time.

The new packs will be available for existing and new Astro customers starting 9 November 2021.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be experiencing this problem.    

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

Discover thousands of movies and series you'll love, and we are continuously expanding. If you would like to enjoy more movies on top of your current subscription, press the Home button and select On Demand. Use the arrow keys to scroll to Store. Pick and choose to rent any movie for up to 48hours.

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which could  cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

To allow customers to decide on their WiFi connection arrangement based on their preference upon being advised by the installer on-site.

User to manually connect their devices to different WiFi bands based on their usage and preference.

You have exceeded the maximum number of registered devices allowed. To manage devices on Astro GO, go to Settings > Registered Devices to view / remove devices from the list of registered devices to your account.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.
 

This error indicates that you are streaming on Astro GO while being connected to a VPN. Please close your VPN application and try streaming again.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.

The new packs come with 200 hours of Cloud recording by default. If your current recordings exceed 200 hours, the system will delete the exceeded hours once your package has been changed, starting with the oldest recordings first.  

If you would like to retain the previous recordings which exceed 200 hours, you may opt for a selection of 400 or 1500 Cloud Recording hours at a chargeable rate of RM12 or RM15 per month (excl. govt tax) respectively. Or else, you may subscribe to the Platinum pack which comes with complimentary access to 1500 hours of Cloud Recording.

No, the Astro Fibre App is a free mobile application for all Astro Fibre customers with the latest RG21 router.

What is beIN SPORTS CONNECT?

beIN SPORTS CONNECT is the ultimate live streaming sports service that provides you with access to global sporting events both LIVE and on-demand such as major European football leagues and over 3,000 hours of live tennis via Astro's Ultra Box, Ulti Box, mobile app or web.

How do I access the beIN SPORTS CONNECT app on the Ultra/Ulti Box?
On the beIN SPORTS CONNECT mobile app:
Step 1: Open the "beIN SPORTS CONNECT" app and go to your Profile
Step 2: Select "Sign in with Astro" and log in with your Astro ID
Step 3: Go to "Settings" and select the TV Login option
Step 4: A QR code scanner will appear.

Follow the steps below to pair the mobile app with your TV screenOn the Astro Ultra/Ulti Box:
Step 1: At Astro Home, go to the app rail and select "beIN SPORTS CONNECT"
Step 2: Go to the Profile icon at the top of your screen and click "OK"
Step 3: A QR code will be presented on your screen. Use the in-app QR code scanner on your mobile device to scan the QR code
Step 4: Your TV screen will refresh automatically and you will be able to enjoy the beIN SPORTS CONNECT app on your TV!

Who is entitled to access the beIN SPORTS CONNECT app on the Ultra/Ulti Box?
Only Astro customers with the Sports subscription as part of their Astro TV Pack (Bundle or add-on) will be able to enjoy the beIN SPORTS CONNECT app on their Ultra/Ulti Box. For further enquiries, please WhatsApp "Get beIN" to our Customer Contact Center at 03-9543 3838.

What are the content available in the beIN SPORTS CONNECT app?
Customers can enjoy major European football leagues, over 3,000 hours of live tennis and other global sporting events LIVE and on-demand on the app. You may check out the complete list of competitions available on the app here: beIN SPORTS CONNECT | Live Leagues and Competitions | LaLiga, Serie A, Ligue

Can I stream on more than one device at the same time?
No, you can only stream the beIN SPORTS CONNECT app on one device at a time.

How many devices can I use to watch beIN SPORTS CONNECT?
You can have up to five (5) devices registered to your account at any given time. However, you can only stream from one (1) device at a time.

Can I download content for offline viewing?
Unfortunately, downloading of content is not a feature that is currently available.

Are subtitles or dubbing available for the content on beIN SPORTS CONNECT?
Unfortunately, subtitles and dubbing options are currently not available.

How can I subscribe to beIN SPORTS CONNECT via Astro?
The beIN SPORTS CONNECT app is not available as an add-to-bill option. Please visit www.product.astro.com.my/tv to sign up to one of our TV Packs with the Sports subscription.

Can I access the beIN SPORTS CONNECT app outside of Malaysia?
No, you will not be able to watch beIN SPORTS CONNECT content outside of Malaysia as the app is geo-blocked for each country.

How do I register for an Astro ID?
Download the beIN SPORTS CONNECT app > Select "Login with Astro"> Click "Do not have an Astro ID? Click here".

Can I update my email address/mobile number for my Astro ID?
Yes, please visit Astro's Self Service Portal via myastro.astro.com.my to update your email address or mobile number.

I have forgotten my password; what should I do?
Step 1: Click "Log in" and click "Forgot my password"
Step 2: Enter your email address and click "Submit"
Step 3: An email will be sent to your registered email address with further instructions on how to reset your password

How do I unlock a locked user account?

You may contact Astro's Customer Service by:

1. Submitting a feedback form here: https://support.astro.com.my/feedback-form
2. Reaching out to us via WhatsApp by typing "Hi" at 03-95433838 for assistance

STEP 1
Check on the adapter's power light.
If the adapter's power light is ON, please refer to Blank Screen troubleshooting steps here.
Otherwise, if the adapter's power light  is OFF, switch off the power for your box.

STEP 2
Ensure power cable is connected tightly.
Plug in power cable to different power socket and switch on the plug.
You should no longer be experiencing this  problem.
If issue remains, proceed to STEP 3.

STEP 3
Try a different power socket to connect the equipment.
Turn on the power socket and check the adapter's power light.

If there is no light on your power adaptor's, please submit the issue on our Feedback Form and attach a picture of your smart card number for assistance.
Please indicate in the form if any lightning strike/thunderstorm/power trip occurred.

STEP 1
Please wait while your Astro box initializes.



STEP 2
Select your preferred language.



STEP 3
Navigate to Next and press "OK".



STEP 4
Select Auto as the Video Resolution.



STEP 5
Navigate to Next and press "OK".



STEP 6
Navigate to Confirm and press "OK" to confirm your selection if you are able to read the texts on screen properly.
Otherwise, navigate to Cancel to revert to the previous settings.



STEP 7
Select IPTV Plug & Play (self-install) as the box operating mode.



STEP 8
Navigate to Next and press "OK".



STEP 9
Select your preferred connection.
For connection via Wi-Fi, proceed to STEP 10.
For connection via LAN Cable, proceed to STEP 16 once you are connected.



STEP 10
Please wait while your Astro box searches for available Wi-Fi networks.



STEP 11
Navigate to your preferred Wi-Fi network and press "OK".



STEP 12
Please enter the password to connect to the Wi-Fi network.



STEP 13
Navigate to Done to continue.



STEP 14
Please wait while your Astro box connects to the internet.



STEP 15
Navigate to Yes to allow your Astro box to connect to this network automatically.
Otherwise, navigate to No.
Proceed to STEP 17 for the next step.



STEP 16
Navigate to Next and press "OK". 



STEP 17
Your box's connection status will be displayed.
Navigate to Finish to complete the setup.

1. Router Positioning
   • Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
   • High vs. Low
     • Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals
     • ​Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for WiFi signals to penetrate.
   • Distance to Router
     • ​ The further away from your router you  get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
     • Otherwise, you should place your  router near the center of your home. After all, WiFi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.
2. Wireless Interference & Noise
   • You've probably never  noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices,  WiFi routers, satellites, cell towers, and more.
   • Although WiFi is  supposed to be on a different frequency than most of these devices, the  amount of radio noise can still cause interference. Some common causes of interference include:
     1. Microwaves
     2. Bluetooth Devices
     3. Cordless Phone
3. Surrounding Wi-Fi signals
   • A truth of the modern world is that every  household has their own WiFi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many  routers within close proximity.
   • Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels  for you automatically, but sometimes it's better to investigate and find the best channel yourself.
4. Usage
   • More likely, however, is that the people  on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/ Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

Any packages with Entertainment Plus, Movies Plus & Sports Plus will include Netflix. The default Netflix offering is Netflix Standard (2 screens and HD viewing) as part of your Entertainment Plus, Movies Plus and Sports Plus subscription. You can upgrade up to Netflix Premium (4 screens and 4K UHD viewing) at a price of RM 10 (inclusive of govt. tax).  

Note: For the above subscriptions, you may use the email address used for your existing subscription with Netflix to activate and the future billing for Netflix will be transferred to your Astro bundle charges. For users that are billed for Netflix through Apple before joining the Astro bundle, remember to cancel your Apple billing arrangement after activating the Astro bundle else you may be double charged for your Netflix account.

If you do not have a bundle which includes Netflix, you may also add a new Netflix subscription to your Astro Bill for billing convenience.

You will not be able to switch between channels, use the app as a remote control, view favorite channels and programmes, use programme showtime reminder, and remote record feature.

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.
2. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem connection

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - LAN  port) to PC/Laptop.

4. If you have change the password in Selfcare Time portal recently, please change the router configuration follows the new password made in  Selfcare, but if you didn't make any changes, please go to Step 5.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 2 / Option 3

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.

2. Gently remove fiber optic cable and  blow / wipe the tip of the fibre cable. This is to clean up the cable in  order to avoid any interferences.

3. Re-insert the fiber cable to the  optical port behind the modem.

4. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem Connection

Router Connection

5.  Make Sure both cables on Modem (LAN Port 4 /LAN Port 3 for second decoder) and Astro Decoder (Network Port) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after  reboot.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.


Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/ power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

Option 5

1. Please ensure LAN cable is directly connected to modem port LAN 1.

2. Please use different LAN port if LAN 1 port is still off / not working.

3. If the issue persists, submit your feedback form for further assistance.

Yes, a penalty fee of RM200/Mesh WiFi unit will be imposed if the customer fails to return the device(s). The courier company will make two attempts to retrieve the Mesh WiFi unit(s) within a period of 30 days, failing which the penalty would be imposed.

For Ultra/Ulti Plug & Play Box installation, it is recommended that you attempt to self-install by following the installation guide here, but there is an option to request for an installer to install the box at your premise. However, there will be a separate fee for this service request.

Astro continuously reviews its content proposition to offer the best choices and a variety of compelling content for our customers for the best viewing experience. As such, we will cease the sale of PPV passes on CH200 from 8 October onwards.

Customers can continue to enjoy their favourite content by subscribing to the relevant packs and stay tuned for more exciting offers to be announced soon.

Should there be any changes in plans we will keep our customers informed on any new development.

Currently, Maxis, Digi, Celcom, TuneTalk, U-Mobile, Yes, XOX and Webe.

For Platinum Pack and Multiroom Smart TV customers, Astro GO+ is included in your subscription at no extra charge. For customers on other packages, you will be able to add-on Astro GO+ to your subscription for RM 5.99/month.

Please use your Astro ID to log in to the Astro Fibre App. If you do not have an Astro ID, kindly follow the simple steps here to create one.

Some of our payment partners require payees to scan the barcode on the statement to make payment. Always bring your Astro bill statement when making payment over the counter.

Astro is continuously improving our user interface and introducing new features to our platforms to ensure that your Astro experience is more seamless, efficient and user-friendly.

For details on our latest interface, Picture-in-Picture mode and auto-start interactive mode on Astro GO, please click here.

In addition, we have also recently introduced a new look to the Title Information Page, the ability to disable the Profile Selection Screen and adjustable auto-standby timing. For more information, please click here.

You will only be able to watch Astro GO and/or Multiroom Smart TV on up to 2 devices at the same time as opposed to 4 devices with Astro GO+. 

Your cloud recording storage will also decrease from 1500 hours down to 200 hours. Your stored recordings/downloaded shows that exceed 200 hours will also be removed. 

No, you need to have an Astro ID to enjoy the features.

Yes, as part of our Astro Fibre Movies & Sports Campaign, new Astro Fibre customers can enjoy 50Mbps + the Movies/Movies+/Sports/Sports+ Pack TV bundle for a special price from only RM164.99/month when they sign up within the campaign period, with more than RM800 savings in total.

Deposit of RM500 (Maxis) and RM300 (Allo) is payable by new subscribers (non-Malaysian). The fee will be reimbursed when service is terminated.

No deposit required for all existing Astro customers and new subscribers (Malaysian).

Please ensure that you have subscribed to the mentioned channel.
If you're subscribed to this channel, follow below steps.

STEP 1
You need to refresh the signal on your box.
Refer to Refresh signal of your box guide.

STEP 2
If issue persist after 30 minutes, proceed to submit report via WhatsApp or Feedback Form.

After service termination of your Astro Fibre service, we will call you via your registered mobile number (up to 3 times over 3 days) to schedule an arranged pick-up by one of our Astro agents. Our agent will then come to your doorstep, dismantle the devices for you and retrieve them.  

Note: Upon termination of your service, customers are required to return their old Astro Fibre devices to Astro. Failure to do so will incur a fee of RM200 (WiFi Router), RM500 (Fibre Modem) and RM200 (Mesh WiFi Unit - if applicable) for each unit. All prices stated are exclusive of Govt. tax.

Astro is an official distributor of Disney+ Hotstar, the dedicated streaming home for global, and Malaysian hits. Astro customers can now subscribe to Disney+ Hotstar through the new, bigger and more diverse Packs, i.e.: Movies, Premium 1, Premium 3 or Platinum Pack. The streaming service brings together blockbuster movies from Hollywood to Hallyu and award-winning content from Disney, Marvel, Star Wars, Pixar, National Geographic, FX, 20th Centuary Studios and more including exclusive premieres from leading Malaysian studios. Take your family entertainment to the next level with Disney+ Originals like I am Groot, Prey, Baymax, Obi-Wan Kenobi, She-Hulk, IN THE SOOP: Friendcation and more - with the convenience of one monthly bill for all your entertainment needs. 

Movies Pack, Premium 1, Premium 3 and Platinum customers as well as customers on the Starter Plus Pack, Value Plus Pack, and Disney+ Hotstar (3-months Pass) can enjoy Disney+ Hotstar on Astro. 

Customers can subscribe to Disney+ Hotstar via astro.com.my/Disney, as well as via authorised retailers and dealers. 

You will be able to check your balance, switch to e-billing, request for payment barcode and request for reconnect at standard telco rate.

Mesh WiFi technology greatly improves the WiFi network coverage within your home and virtually eliminates all WiFi “dead spots”. However, like all technologies there are limitations that you should be aware of.

‍

The pairing of Mesh unit to the WiFi router is automatically handled between the WiFi router and the Mesh unit after it calculates its current position in relation to the WiFi router and surrounding Mesh unit (if available) already connected to the WiFi router.

‍

If you are self-installing the mesh at your house, it is advisable for you to always pair the Mesh unit(s) with the WiFi router only regardless of how many Mesh unit available at your house. 

‍

Please note that if you have a Mesh connected to another Mesh, the expected performance of the WiFi speed will  not perform as  optimally as when compared to a Mesh connected directly to the WiFi router. Adding more points (also referred as Number of hops) in between your device to the WiFi router which will cause a reduction in bandwidth and add latency.

1. Power reset (on & off) your Modem and Router.

2. Ensure standard physical connection (No 3rd party devices connected to decoder and modem).

3. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

4. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

5. On the address bar, type https://testmyline.astro.com.my/ and below page will appear.

6.Click "GO", and the test will begin.

The test is completed once both download and upload speeds are displayed.

Sample of the Speedtest result is shown below.

**Please ensure the snapshot includes a time stamp and network used either LAN cable or wireless (as per picture above)

7. Kindly screenshot or take a picture of the result, name it as "LAN Speedtest" for test using LAN cable (wired connection).

8. Repeat the test once again using WiFi connection (Please unplug your LAN cable and connect via wireless connection using your SSID).

9. Screenshot or take a picture of the result, name it as "WiFi Speedtest".