By default, the band steering featured is disabled. Follow these steps to enable it.

Note: Band Steering is called Dual-band Combination in the router web interface.

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).
2. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user
Password: user

 

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi to configure the WiFi parameters.

6. Click on Dual-band Combination button to enable the Band Steering.

7. A pop-up message will appear showing "The device network may be disconnected when dual-band combination is enabled". Click "OK" to proceed.

8. Set the Wi-Fi name and Wi-Fi password based on customer's preferences. Then click "Apply" for the changes to take place.

Please reconnect to the new Wi-Fi name with the new password once completed.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Standby Mode and press "OK".

STEP 4

Navigate to your preferred selection and press "OK".

STEP 5

Navigate to Save and press "OK" to confirm your selection.

Astro Fibre subscription also comes with a 24-month contract commitment and will NOT be auto renewed at the end of contact period.

In general, these two bands can be differentiated with these parameters: Coverage, Channel Interference and Speed.

2.4GHz gives better coverage but lower speeds, while 5GHz provides faster internet but covers a smaller area.

Rebates/refunds are not provided. Early termination of the 3-months pass add on is subject to an early termination fee prorated to RM54.90 for the remaining months.

No, the quality of your video depends on the speed and reliability of your internet.

By changing from a 12-months commitment period to 24-months, there will not be any cancellation fee applicable. You will start a new contract with 24-months commitment and receive the corresponding discount for that duration.

If you did not receive the recovery email or verification code, please make sure that:

1. You are inserting the correct email or mobile number you used to register for your Astro ID.
2. Check your junk mailbox or spam folder.  

To find out which email or phone number you have used to register your Astro ID, you may submit a feedback form. Kindly select feedback type "I have an enquiry/issue with Apps" choose "Astro GO" 
 

We will get in touch with you within 48 hours to solve your enquirie

If you have NOT made any changes to your Astro pack on or after 9th November 2021, you can enjoy up to four (4) concurrent streams on Astro GO anywhere, anytime. However, if you have Astro GO+ as part of your subscription, you will be upgraded to four (4) concurrent streams.

Astro introduces Liga Malaysia for all Astro customers to watch the Malaysian Football League’s Liga Malaysia competitions LIVE, comprising Perlawanan Sumbangsih (Piala Sultan Haji Ahmad Shah), Liga Super, Piala FA and Piala Malaysia live in HD on Astro Arena (CH801), Arena Bola channels (CH803 and CH804) and stream on Astro GO until further notice.

If Astro does not receive your payment by the stated due date, your service may be disrupted as our system will automatically suspend your account. If you then wish to reconnect your subscription account, a charge of up to RM42.40 (inclusive of SST) will be imposed upon reconnection.

Find out more about the reconnection fee here.

No, Astro & Broadband only offers a 24-month contract period upon sign up.

The main features and changes in this update are the revamped look and feel of Astro's user interface on the Astro Ultra/Ulti Boxes and Astro GO, which include redesigns to the Astro interface that consists of title rows at the Home Page to feature popular franchises, new live programmes posters and changes to the menu bar for easier navigation; auto-start Interactive Mode on Astro GO; as well as a Picture-in-Picture mode that shrinks your video player so you can keep watching your favourite shows while using other apps.

The details of each feature are:

• New Astro user interface
• Picture-in-picture mode
• Auto-start Interactive Mode on Astro GO

For more info, please read our dedicated FAQ on this here.

Please be sure to take your decoder, satellite dish, smartcard, remote control and all other fixtures after dismantling is done by the technician.

Please ensure you:  

a. Have your original identification card “MyKad” (Front & Back) with you (Malaysian).

b. Have your original Passport & Visa with you (Non-Malaysian).

c. Are in a brightly lit environment

No, you can remain in your current pack, however starting 9 November 2021, you would need to subscribe to the new packages to make any changes to your subscription. We strongly encourage customers to switch to the new packs to enjoy the best content experience from Astro.

You will receive SMS notifications upon successful sign-up with a delivery tracking number for the Plug & Play Box and the Astro SIM card.

The WiFi SSID and password of the Mesh unit will be automatically synchronized to the WiFi router. Hence, there is no need to configure the WiFi parameters.

*WiFi SSID (Service Set Identifier) is the name of your wireless network, also known as Network ID. It is viewable to anyone with a wireless device within reachable distance of your network.

Connect your PVR to Wi-Fi and enjoy access to our library of Video On Demand. Replay old seasons, catch-up latest episodes of your favourite shows, anytime you want. To connect your PVR, follow the steps below depending on your box type:

(a) Wi-Fi Enabled PVR (DMT5)

·      Press the “Home” button and select “Settings” > “Network” > “Wi-Fi”

·      Allow the PVR to scan Wi-Fi networks available and subsequently choose your home Wi-Fi network > Enter your Wi-Fi password if required

·      Once connected, the icon below will appear on the screen.

‍
      Tip: Use the alpha-numeric keyboard on your Astro Remote to key in your password

·      Press the “Home” button and select “On Demand” to start watching videos on demand!

‍

(b) Non-Wi-Fi Enabled PVR (HD PVR)

There are two ways to connect your HD PVR decoder to your home Wi-Fi
(i) Using the Ethernet (LAN) cable 
 

·       Plug in the LAN cable from your modem into the PVR network port

·       Once connected, the icon below will appear on the screen

·       Press the “Home” button and select “On Demand” to start watching videos on demand!

(ii) Using an Astro Wi-Fi dongle as per shown below

Step 1 - Plugin the Wi-Fi dongle into the front USB part of your PVR decoder.

Step 2 - A prompt will appear stating "Do you wish to connect to a wireless network?", select "Yes, continue."

Step 3 - Once connected, the Wi-Fi icon will appear on the screen. Now you are ready to download and enjoy Astro's on demand entertainment.

Step 4 - Press the “Home” button and select “On Demand” to start watching videos on demand!

*The Wi-Fi dongle is only applicable for the non-Wi-Fi enabled PVR (as per the picture).

Astro subscribers will have the freedom to subscribe to Netflix via Astro, or they may also choose to continue subscribing via Netflix directly on their own.

Please refer to these FAQs for more information, or click here to learn more and sign up for the Ulti Box. Alternatively, you may call 03-7481 8000 to get in touch with an Astro representative.

Option 1

1. Please turn off  all devices (Modem and Router). By restarting your modem, you can isolate the  possibility of overloaded processes in the modem, which would impact its  performance.
2. Ensure both cables on Modem (LAN Port  1) and Router (Internet Port) are properly connected.
    

Modem connection

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - LAN port) to PC/ Laptop.

4. If you have change the password in Selfcare Time portal recently,  please change the router configuration follows the new password made in Selfcare, but if you didn't make any changes, please go to Step 5.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option 2/ Option 3

1. Please turn off all devices (Modem and  Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.
2. Gently remove fiber optic cable and blow / wipe the tip of the fiber cable. This is to clean up the cable in order to avoid any interferences.
3. Re-insert the fiber cable to the optical port behind the modem.
4. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem Connection

Router Connection

5. Make Sure both cables on Modem (LAN Port 4/ LAN Port 3 for second decoder) and Astro Decoder (Network Port) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.


Option 5

1. Please ensure LAN cable is directly connected to modem port LAN 1.

2. Please use different LAN port if LAN 1 port is still off / not working.

3. If the issue persists, submit your feedback form for further assistance.

Deposit of RM500 (Maxis) and RM300 (Allo) is payable by new subscribers (non-Malaysian). The fee will be reimbursed when service is terminated.

No deposit required for all existing Astro customers and new subscribers (Malaysian).

If you would like more information or to provide feedback, kindly log in to our support page via support.astro.com.my. For more questions regarding Astro Pack, you may reach out to us via call at 03-7481 1000 (Monday to Friday, 9AM – 6PM exclude public holidays).
 

Liga Malaysia is available for all customers with a HD enabled box including Zapper, DMT5, Ulti Box and Ultra Box.

You will need to have an Astro subscription before you can subscribe to Disney+ Hotstar as an add-on service via Astro or enjoy any Astro bundle promotions. Please click here to subscribe to our Movies, Premium 1, Premium 3 or Platinum Pack to enjoy all your favourite Global and Malaysian hits for even better value and savings!

Although anyone can create an Astro ID, only the Astro account owner is allowed to link their account to the Astro ID. Otherwise, you will need permission from the account's owner in order to complete the linking.

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

No. However, if you cancel your Astro Pay TV services but resubscribe at a later date, your duration (year) with us will reset to zero and restart according to your new activation date. Your Astro Rewards tier will reset to Magenta.

STEP 1

While watching  linear channel, press “OK” to  launch player banner.

STEP 2

Press “OK” again to Pause. You will see an Icon on the left of TV screen.

STEP 3

Press “OK” again to resume the program.

STEP 4

Navigate to Back To Live TV and press "OK" to go back to the live view.

Please check your internet speed and connection status via internet connection test. If your internet is working fine and the issue persists, proceed to submit report via WhatsApp or Feedback Form.

Yes, you are eligible for selected bundle packages with rebates up to RM39/month and a free speed upgrade if you subscribe within the promotion period. Kindly note that monthly rebates are only available for Pay TV + Astro Fibre bundles but the speed upgrade is available for all packages including standalone plans.
 

Photograph or scan your payment receipt, and send it to one of our contact platforms found here.

Step 1: Download the My Astro app from either the App Store, Google Play or HUAWEI AppGallery.

Step 2: Sign in with your Astro ID.

Step 3: Select "Rewards" on the home screen to get started.

Watch this tutorial to learn how to create your Astro ID.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the Smartcard at the front or right side and gently pull it out make sure that the adapter's power light is off.

STEP 3

Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be  experiencing this problem.

If issue persist, please submit your feedback form with error details and attach a picture of your sim card number for assistance.

Astro does not provide installment plan facilities. You are advised to pay your charges before the due date, as per your monthly bill statement.

There are two ways for you to switch your preferred bill delivery method:

‍

A. Customers can manage their account via the My Astro Portal by following these easy steps:

1. Visit www.astro.com.my
2. Select “My Account”, then select “Manage Account”
3. Log in to My Astro Web using your Astro ID
4. Select “Account” 
5. Under “Billing”, click on “Bill Delivery Method”
6. Choose your preferred bill delivery method, then click “Proceed”

B. Customers can also manage their account via Astro’s mobile application, the My Astro app by following these easy steps:

1. Open the “My Astro” app on your smartphone. If you do not have it installed, you may download it here (Google Play Store) or here (IOS App Store)
2. Log in with your Astro ID
3. Select “Account” in the navigation bar
4. Select “Bill Delivery Method”
5. Choose your preferred bill delivery method, then click "Proceed

No, Pay-Per-View is no longer available in CH200.

We would need you to  run few tests in order for us to understand your issue and to assist you in fixing the problem.

You may proceed with the troubleshooting steps below which should not require any longer than 15 minutes.

1. Please run each of  the tests according to your your Laptop/PC Software.
2. Compile the pictures / screenshots of  your test results in one file (i.e Microsof Word document, PDF file) and attach them in the Support Ticket below in order for us to assist you further:
   • List of websites effected.
   • Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.
   • Run the Traceroute Test - Please click here for Traceroute Test guideline.
   • Run the Ping Test -  Please click here for Ping Test guideline.
3. Once you/ve gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

The default PIN is 0000. You may change your PIN to a secure one by doing this at Settings, under your Preferences, select PIN Management, enter your old PIN or default PIN and proceed to create a new PIN.

Kindly ensure that your mobile number is the same as the registered phone number of the Astro account holder as the OTP will only be sent to the registered number. For further assistance, please call or WhatsApp us at 03-9543 3838. Alternatively, you may submit a request via our online Feedback Form here: astro.com.my/contactus/form.aspx. 

For customers that would like to subscribe to Multiroom with a box installation,

(i) customers on the old packages (example Family Pack, Starter Pack, Value Pack, Super Pack or Super Pack Plus) will have to subscribe to our new packages first by sending "Switch" to 03-9543 3838 via WhatsApp;

(ii) customers on the new Astro packages can subscribe by visiting product.astro.com.my/multiroom or WhatsApp "Hi" to 03-9543 3838.

My Astro is available on web browser and app. The app can be downloaded for free from the Google Play Store, Apple App Store or Huawei App Gallery.

For Ultra and/or Ulti box users, My Astro app is now added to the Top Menu so you can easily access it to manage or update your account. You may find it in the Top Menu, located next to Settings. Please refer to the image below to see what it looks like:

Please contact us through one of our platforms found here or Self-serve by logging in to Astro Self-Service Portal within 3-7 days before moving out and we will sort everything out for you!

You can proceed with below troubleshooting if the weather is good. Ortherwise, you may try again later.

STEP 1
On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.


STEP 2
Navigate to SETTINGS and press “OK”.


STEP 3
Navigate to STB DIAGNOSTICS and press “OK”.


STEP 4
Refer to the signal strength % shown on the top left of your screen.
If it is 65% or higher, please go to WhatsApp to receive further help.
If it is below 65%, please go to STEP 5.


STEP 5
Switch off the power for your box and make sure that the adapter’s power light is off.


STEP 6
Unscrew the satellite cable from the box and pull it out.


STEP 7
Plug the satellite cable back into the box and screw it back securely.


STEP 8
Switch on the power for your box and make sure that the adapter’s power light is on.
Please wait for 5 minutes.


STEP 9
Turn on your box. You should no longer be experiencing this issue.
If issue persist, please attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized Dish
 If issue persist under a centralised satellite dish, please refer to your respective Building Management before contacting our agents.

No, you will not be charged 8% Service Tax for paper billing option.

Yes, there are five digital bill platforms available for all customers to check their Astro bills: 

A.    MyAstro Web

1.    Visit www.astro.com.my

2.    Goto “My Account”, then select “Manage Account”

3.    Login to My Astro Web using your Astro ID

4.    Select “Account” to view your bills 

B.     My Astro app

If you do not have it installed, you may download it here (Google Play Store) or here (IOS App Store)

‍

C.    WhatsApp 

Just WhatsApp “Hi” to 03-9543 3838 and then follow the instructions to view your bill, account status, pay and download bill. 

Note: You are required to provide your MyKad/PassportNo. to view your bill, account status and pay your bills. To download your bills, you will be required to provide your Account/Smartcard No.

D.     Astro Quick Pay 

1.    Visit https://pay.astro.com.my

2.    Enter your 10-digit Astro Account Number and follow the instructions to view your bill, account status, pay bills or add a billing reminder on your Google calendar. 

E.    IVR

1.    Call +603-95433838

2.    Press 1 for Account Related Queries

3.    Input your 10-digit Astro Account no. or 12-digit MyKad no.

4.    Press 2 for Payment and Billing

5.    Press 1 to receive an SMS with your bill balance and a link to pay online

F.    Channel 200

Ensure your Ultra or Ulti Box is connected to the internet. Tune in to CH200 and follow the instructions displayed on your TV screen to view your bill amount.

G.     Auto-Debit

Alternatively, please register for Auto-Debit by following the steps here for hassle-free payments.