You will receive two SMS notifications with tracking numbers separately from the courier service, one for the Plug & Play Box and one for the Astro SIM card. Please expect these SMS notifications to be sent to you within 2-3 working days upon successful order submission (online or via retailer).

STEP 1

Switch OFF the power of your Ultra / Ulti box and make sure that the adapter's power light is off.
 

STEP 2

Switch ON the power of your Ultra / Ulti  box and make sure that the adapter's power light is on.
 

STEP 3

On your remote control, press the Home or Standby button repeatedly until the Startup Options appear on TV.



STEP 4
Press "987" to proceed.
Advanced Startup Options will be displayed.



STEP 5
Press "1" to initiate a reset setting.



STEP 6
Press "OK" to continue.



STEP 7
After the factory setting is restored, TV will turn blank.
Please wait until the box completes initiate setup.



STEP 8
Once completed, the following screen will appear on your TV.
Refer to Installation Setup guide to complete the setup.

Click here to follow New Installation Settings guide for Satellite
Click here to follow New Installation Settings guide for Plug and Play

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Video Resolution and press “OK”.

STEP 4

Navigate to your preferred selection and press “OK”.

Recommended to select Auto.

STEP 5

Navigate to Save and press "OK" to confirm your selection if able to read the text properly.

Otherwise, navigate to Cancel to revert to previous settings.

Option 1

1. Please turn off  all devices (Modem and Router). By restarting your modem, you can isolate the  possibility of overloaded processes in the modem, which would impact its  performance.
2. Ensure both cables on Modem (LAN Port  1) and Router (Internet Port) are properly connected.
    

Modem connection

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - LAN port) to PC/ Laptop.

4. If you have change the password in Selfcare Time portal recently,  please change the router configuration follows the new password made in Selfcare, but if you didn't make any changes, please go to Step 5.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option 2/ Option 3

1. Please turn off all devices (Modem and  Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.
2. Gently remove fiber optic cable and blow / wipe the tip of the fiber cable. This is to clean up the cable in order to avoid any interferences.
3. Re-insert the fiber cable to the optical port behind the modem.
4. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem Connection

Router Connection

5. Make Sure both cables on Modem (LAN Port 4/ LAN Port 3 for second decoder) and Astro Decoder (Network Port) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.


Option 5

1. Please ensure LAN cable is directly connected to modem port LAN 1.

2. Please use different LAN port if LAN 1 port is still off / not working.

3. If the issue persists, submit your feedback form for further assistance.

For existing Astro Fibre customers with the WiFi 6 Huawei K562e router, youwould need to upgrade to the latest RG21 router in order to access the AstroFibre  with a one-off fee of RM300 (excluding SST). For any enquiries, please contact our Customer ContactCentre at 03 - 9543 1543and an Astro agent will be available to assist you immediately.

The promotion period of Astro Fibre’s Speed Upgrade Campaign is from 24 November 2023 until 31 May 2024.

Yes, you will need to pay additional RM25 per remaining contract months per unit on top of the standard Broadband penalty fee should you terminate the contract within 24 months.

It will begin on 1st March 2024 and onwards.
 

1. Clearly indicate full name of Astro customer, contact number and Astro subscription account number when making each payment (e.g. on bank-in slips)
2. For Direct Debit, please contact your bank for standing instructions. Provide the full name of Astro customer and Astro account number. The Direct Debit service may not be available with all banks. Please check with your bank for confirmation of Direct Debit service.
3. Please inform us of any changes in billing address/information by contacting us via one of these platforms.

IMPORTANT NOTICE: To avoid any problems in payment processing, please pay only at authorised Astro payment channels

No, you need to have an Astro ID to enjoy the features.

No, the Ulti Box does not support 4K UHD content. If you would like to watch Astro's 4K UHD content, please sign up for an Ultra box at Astro Ultra Box and Ulti Box | Astro.

You may utilise your credit balance to offset future billing on your Astro account, or contact us here for further enquiries.

I am sorry you can't. While we understand the value customers see in choosing their preferred service/pack individually, the packaging of channels/services in the new packs are necessary for us to offer content/services at an affordable price to our customers.

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3  

Navigate to Satellite Settings and press "OK".

STEP 4  

Select Diagnostics and press "OK".

STEP 5    

Signal reading on Tuner 1 will be displayed. Navigate to right arrow for next step.

STEP 6  

Signal reading on Tuner 2 will be displayed. Navigate to "Done" and press "OK" to complete the diagnostics.

Call our contact centre 03-9543 3838 or visit us at astro.com.my.

Astro is an official distributor of Disney+ Hotstar, the dedicated streaming home for global, and Malaysian hits. Astro customers can now subscribe to Disney+ Hotstar through the new, bigger and more diverse Packs, i.e.: Movies, Premium 1, Premium 3 or Platinum Pack. The streaming service brings together blockbuster movies from Hollywood to Hallyu and award-winning content from Disney, Marvel, Star Wars, Pixar, National Geographic, FX, 20th Centuary Studios and more including exclusive premieres from leading Malaysian studios. Take your family entertainment to the next level with Disney+ Originals like I am Groot, Prey, Baymax, Obi-Wan Kenobi, She-Hulk, IN THE SOOP: Friendcation and more - with the convenience of one monthly bill for all your entertainment needs. 

Movies Pack, Premium 1, Premium 3 and Platinum customers as well as customers on the Starter Plus Pack, Value Plus Pack, and Disney+ Hotstar (3-months Pass) can enjoy Disney+ Hotstar on Astro. 

Customers can subscribe to Disney+ Hotstar via astro.com.my/Disney, as well as via authorised retailers and dealers. 

You may manage all your Astro subscriptions via My Astro app. Download here or on your App Store or Google Play Store.

Astro is an official distributor of Disney+ Hotstar, the dedicated streaming home of global, and Malaysian Hits. Astro customers can now subscribe to Disney+ Hotstar through our Movies, Premium 1, Premium 3 or Platinum Pack and enjoy award-winning entertainment with Disney+ Hotstar alongside Astro's much-loved local content for even better value and savings. Now, customers can enjoy Disney+ Hotstar on their Ultra or Ulti Box, mobile app or web! In addition, customers who have multiple primary Astro accounts will be entitled to multiple entitlements to Disney+ Hotstar.

Rebates/refunds are not provided. Early termination of the 3-months pass add on is subject to an early termination fee prorated to RM54.90 for the remaining months.

Starting 29 August 2022 (for Ulti Box customers) and 2 September 2022 (for Ultra Box customers), you will be able to log in to Disney+ Hotstar using your registered mobile number by following these simple steps: 

Step 1 - You will receive a Disney+ Hotstar auto-activation SMS on your registered mobile number. 

Step 2 - Press the Home button on your Astro remote. Under the "Apps

Please follow the steps below:

Step1: Fill in Merge/Split Equipment Form (Part A & Part B)

Step2: A full payment to be made on any outstanding balance for all related accounts (if any).

Step3: Submit all documents via feedback form or walk in to nearest Astro Customer Service Centre (CSC).

Step4: Customer will expect a call from our validation team (Note: Turnaround time for merge/ split of account is 3-5 working days upon receiving all complete documentation).

Note:

1. There might be a loss of transmission during the processing of transfer equipment ownership, split or merge of equipment.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the Smartcard at the front or right side and gently pull it out make sure that the adapter's power light is off.

STEP 3

Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be  experiencing this problem.

If issue persist, please submit your feedback form with error details and attach a picture of your sim card number for assistance.

1. Please standby  computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.254 and below page  will appear.

If below box appear, please enter required details:

USERNAME: Administrator

PASSWORD: (ACCESS KEY AT THE RGW STICKER)

(These are the defaults, if you have done previous configuration on your router the password may be different)

4. Once enter into the page "'TECHNICOLOR TG784N V3'', you may follow below steps to get the best wireless channel information.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. In order to get the best wireless channel, click "Wireless Scan" to scan available surroundings wireless Channel.

D. Please choose channel with lesser number of usage.

Example in below case, you may choose channel 4.

5. To configure wireless channel, please proceed with below steps.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. Then, click "Configure" to change the channel selection (automatic to manual) and other configuration option.

D. Please ensure below items:

i. WLAN Enable: Tick

ii. Interface Enable: Tick

iii. Change the Channel Selection to Manual

iv. Change the wireless Channel based on Step 4(D).

v. Once completed the selection, click the "Apply" button.

STEP 1
On your Astro remote, press the HOME button and the home menu will be displayed on top of your screen.


STEP 2
Navigate to Settings.


STEP 3
Navigate to STB Diagnostics and press "OK".


STEP 4
Select General Diagnostics and press "OK".


STEP 5
General Diagnostics results will be displayed on the screen.
Scroll until observed the SW Download Status.

For My Astro App Users 
Go to the "Account' tab and scroll to "Personal Info' section. Click "Name & contact info' to view and update your personal contact information.

For Ultra and/or Ulti Users 

1. Launch the My Astro app on your Home screen and you will land on your My Astro account dashboard. Then, press the yellow button on your Astro remote control to visit your "Account details".
2. Press the down button to view the "Personal info".
3. Press the left button and focus on the edit icon for the contact details, press on "OK" to change your contact details.

If you would like to upgrade your pack to include Disney+ Hotstar Premium, please contact Astro Customer Contact Centre at 03 9543 3838. Alternatively, please WhatsApp Astro at 03 9543 3838 and type DH Help for further assistance. 

Yes, your advance payment will be fully refunded if you cancel your subscription before the Astro box installation. Please call Astro's Contact Centre at 03-9543 3838 for a refund. The refund process will take approximately 14 days for processing with your issuing bank. However, if you decide to cancel your subscription after the Astro box installation (during your contract period), the prorated early termination fee will apply.

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please ensure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Intermittent internet connection using Wi-Fi

1. Router Positioning
   Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
   
    i) High vs. Low
   Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   
   ii) Concrete & Metals
   Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   
   iii) Distance to Router
   The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
   
   Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.
   
    

2. Wireless Interference & Noise
   You've probably never noticed but there are wireless signals all around you wherever you go and they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.
   
   Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:
   i) Microwaves
   ii) Bluetooth Devices
   iii) Cordless Phone
    

3.  Surrounding Wi-Fi signals
   A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel  overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many  routers within close proximity. Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

4. Usage
   More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

• If you have signed up for a PVR (New customers), you will have to maintain your Astro subscription for 24 months, or a pro-rated penalty shall apply.
• If you have signed up for a PVR (Existing customers), you will have to maintain your Astro subscription for 24 months, or a pro-rated penalty shall apply.
• If you took up a PVR decoder at a special offer with the package subscription of Super Pack Lite/Super Pack/Super Pack Plus/monthly subscription > RM169.60 (price includes Govt tax), you will have to maintain your package subscription for a minimum of 6 months, or a flat penalty fee of RM106 (price includes Govt tax) shall apply.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Preferences and press "OK".

STEP 3  

Navigate to Language and press "OK".

STEP 4    

Choose your language preferences and press "OK".

STEP 5  

Select Yes, continue and press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

Yes,existing Astro & Broadband customers within contract or out of contract can subscribe to Astro Fibre offer. The 24-month contract will be renewed.

However, your contract with Maxis/Allo needs to be terminated before signing up to this offer. An early cancellation fee applies if you are still within contract.

‍*Subject to Terms &Conditions of your contract

You must subscribe to an Astro subscription (NJOI customers are not eligible) in order to get the Ulti Box. 

‍

The eligibility criteria for the Ulti Box are as follows:

New Customers

All new Astro customers with a monthly subscription fee of below RM100 will be entitled to select the Ulti Box upon signing up for Astro’s packages. 

‍

Existing Customers (Box Upgrade for Primary or Multiroom)

Existing customers are required to have an internet connection at home with a recommended internet speed of 10Mbps and above in order to upgrade your existing box to Ulti Box. 

Note: 

·      Existing Ultra Box customers are not eligible for a swap to the Ulti Box.

·      If your existing box is a PVR, you will lose access to all the recordings stored in the PVR

‍

Multiroom (New subscription)

Customers subscribing for an additional multiroom subscription are entitled to select the Ulti Box as part of the subscription.

Check out our user guide for a quick and easy way to get started!
 

Download our user guide in English

Download our user guide in Malay

Download our user guide in Chinese

Do you need more information? Watch our Astro Ultra How to videos here.

No, the Mesh WiFi add-on with Astro Fibre is only available as a subscription service and will not be tied to any device contract.

Depending on your service, it is mandatory to return some devices as per our T&Cs, whilst other devices should be disposed of and recycled at collection centres registered under the Department of Environment. To find out what you should do with your devices after service termination, please click here.

All Astro customers and non-customers who have an Astro ID will no longer be able to log in to our digital platforms using their usernames. Users will experience this change if they currently do not use an email address or mobile number to login, for example: johndoe2023.

We noticed that you've recently requested for a change in your Astro account. 

As this change will affect your overall monthly subscription, the expiry date for your Disney+ Hotstar (3-months Pass) subscription has been deferred to xxx (date) to consolidate the final monthly subscription pricing. 

Please refer below to set up your Ultra/Ulti Plug & Play Box.

To connect via LAN cable: 

1. Switch off your old Astro box.
2. To connect your Plug& Play Box via LAN cable:
   a) Remove the LAN cable from your old Astro box and connect the LAN cable to your new Plug & Play Box.
   i) For Maxis IPTV customers, keep the other end of the LAN cable connected to your router.
   ii) For TIME IPTV customers, go to the other end of the same LAN cable, plug it out from your modem, and into any LAN port on your router. Ensure that you’re not plugging your LAN cable back into the same box.
   ‍

Note: If you have a two-in-one modem & router, you can skip Step ii).  

To connect via Wi-Fi:

Remove your LAN cable from your old Astro box, and do not plug it into your new Plug & Play Box.

1. Please standby computer/laptop to access to the internet and connection must be via LAN  (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and  direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.1.254 and below page will appear.

The default login of the router as below. If you have done a configuration on your router previously,  the password may be different.

Username: user
Password: Router S/N (Available on the sticker at the back of the router)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the left menu, choose Wireless 2.4GHz  and then click Basic Settings tab on the left menu to access to below screen.

6. You may change the Wireless Network Name (SSID) and the SSID Password to follow your preferences, then click "Save"  for the changes to take place.

Please reconnect to the new wireless name with the new password once completed.

7. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

You may change the Wireless Network Name (SSID) and the SSID Password to follow your preferences for 5GHz by choosing Wireless 5GHz  then click Basic Settings.

Click "Save" for the changes to take  place and reconnect to the new wireless name with the new password once  completed.

Deposit of RM500 (Maxis) and RM300 (Allo) is payable by new subscribers (non-Malaysian). The fee will be reimbursed when service is terminated.

No deposit required for all existing Astro customers and new subscribers (Malaysian).

STEP 1    

Switch OFF the power of your Ultra / Ulti box and make sure that the adapter's power light is off.

STEP 2    

Switch ON the power of your Ultra / Ulti box and make sure that the adapter's power light is on.

‍

STEP 3  

Put the box on standby mode.

STEP 4

Press and hold the Home button on the box.

STEP 5    

Wait until "boot" appear on the front panel and released.

STEP 6

When “boot” appears, press “Standby”,  “Left “, “Up” continuously until Auto Update appear on box screen and Software Update progress on TV.

‍

‍

STEP 1    

Switch OFF the power of your box and make sure that the adapter's power light is off.

‍

STEP 2

Switch ON the power of your box and make sure that the adapter's power light is on.

STEP 3

Press Standby, Ch+, Standby keys on the box simultaneously when the "boot" message appears on the box front  panel.

The Software Update progress screen will appears.    

The update will take 10 - 15 minutes to complete. Please be patience.

STEP 1  

Switch OFF the power of your box and make sure that the adapter's power light is off.

STEP 2    

Switch ON the power of your box and make sure that the adapter's power light is on.

STEP 3

Press the standby button repeatedly after switch on the power.

STEP 4

Press "OK".

STEP 5    

The Software Update progress screen will appears.

The update will take 10 - 15 minutes to complete.

Please be patience.

For customers with the Ultra or Ulti Box, please ensure to provide your latest contact details to our Astro agent during the call to terminate your account, this includes your mobile number and house address. If you still need further help, please contact us at 03-9543 3838.

STEP 1    

Check your current software version on your box.

If the software version updated (Refer to Table 1) , proceed to STEP 2.

If software version different from Table 1, click here for Software Update guide.

Once software is updated, tune to the impacted channel.        

If issue persist, proceed to STEP 2.

‍

STEP 2  

Run Test Satellite Frequency.    

Click here for the guide.

‍

If dCSS Scan Entrypoint Success, proceed to submit report here.

Guide to submit report:    

At Feedback Type select "I have Astro service related question/request" and Sub Category as "Technical Interruption".

Fill up all the required information and submit.    

Please indicate if you agreed  to recontract for 12 months (technical visit is FOC) or paid visitation (RM65).    

You will receive appointment details via SMS within 48 hours.

If dCSS Scan Entrypoint Fail, proceed to STEP 3.

‍

‍STEP 3    

Proceed to Update Satellite Frequency.

Click here for the guide.
Once completed, tune to the impacted channel.

If issue persist, proceed to submit report here.

‍

Guide to submit report:    

At Feedback Type select "I have Astro service related question/request" and Sub Category as "Technical Interruption".

Fill up all the required information and submit.    

Please indicate if you agreed to recontract for 12 months (technical visit is FOC) or paid visitation (RM65).    

You will receive appointment details via SMS within 48 hours.

The Astro Fibre app is a newly introduced mobile application exclusively for Astro Fibre customers to allow them to schedule when each user can access the internet, share network access to guests in a secure manner, easy device management, amongst many other features for a better WiFi experience. For more information about this app, please visit here.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Subtitles and press "OK".

STEP 4

Navigate to your preferred selection and press "OK".

There are two ways for you to switch your preferred bill delivery method:

‍

A. Customers can manage their account via the My Astro Portal by following these easy steps:

1. Visit www.astro.com.my
2. Select “My Account”, then select “Manage Account”
3. Log in to My Astro Web using your Astro ID
4. Select “Account” 
5. Under “Billing”, click on “Bill Delivery Method”
6. Choose your preferred bill delivery method, then click “Proceed”

B. Customers can also manage their account via Astro’s mobile application, the My Astro app by following these easy steps:

1. Open the “My Astro” app on your smartphone. If you do not have it installed, you may download it here (Google Play Store) or here (IOS App Store)
2. Log in with your Astro ID
3. Select “Account” in the navigation bar
4. Select “Bill Delivery Method”
5. Choose your preferred bill delivery method, then click "Proceed

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

2.Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user

Password: user

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi to configure the WiFi parameters.

6. You may change the Wi-Fi Name and the Wi-Fi Password as per your preferences, then click "Apply".

7. Your Wi-Fi Name and password has been changed. Kindly ensure to reconnect your WiFi according your new WiFi name and password.