STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2A

Unplug the HDMI cable from your box and plug it back in securely. Do select the correct TV input.

STEP 2B

If you are connecting using RCA cable, please unplug the RCA cable from your box and plug it back in securely.

STEP 3

Switch on the power for your box and make  sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 4

Turn on your box. You should no longer be experiencing this problem. If issue remain, replace to another HDMI  cable.        

If no improvement seen, please submit the issue in our Feedback Form and attach a picture of your smart card number for assistance.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

Please ensure to put your box on standby mode to refresh the signal.

a. Using IVR
   ​1. Dial 03-95433838 and select you preferred language.
   2. Select Account Related.

   4. Select Refresh Smartcard.

b. Using MyAstro web
  
STEP 1
Go to https://myastro.astro.com.my/ in your web browser.

STEP 2
Keyin your Email / Mobile number and password. Then, press "LOG IN".
 
STEP 3
Click on TV pack.
 

STEP 4
Choose Main Room for the Primary Box; else choose Multiroom (If any).
 

STEP 5
Click on "Refresh" to refresh signal on your box. 

For Main Box      

For Multiroom

STEP 6
After tap the Refresh, below notification will be displayed as below.

For Main Box 

For Multiroom

c. Using My Astro App

STEP 1
Open My Astro App and click "Login".

 

STEP 2
Keyin your Email / Mobile number and password. Then, press "LOG IN".

 

STEP 3
Go to "Account".

 

STEP 4
Scroll down to "TV pack" and click on it.

 

STEP 5
Choose Main Room for the Main Box; else choose Multiroom (If any).

 

STEP 6
Tap on "Refresh" to refresh signal on your box. 

 

STEP 7
After tap the Refresh, below notification will be displayed as below.

 

Please note that only one Disney+ Hotstar access is bundled to each TV Pack subscription which allows two concurrent streams on Disney+ Hotstar. 

Mac OS X

1. Click the Go tab in the top menu bar and select Utilities from the drop-down menu.

2. Type "network utility" in the search bar in the top right-hand corner of the Utilities window and then hit the "Enter" key on your keyboard. 

3. Click the Network Utility icon to open the Network Utility window.

4. For Ping Test, select the Ping tab and then type the address you'd like to ping in the text box. Click Ping and wait for the ping results.
 

5. For Traceroute Test, select the Traceroute tab and then type the address you like to traceroute in the text box. Click Trace and wait for the traceroute results.
 

Windows 10

1. Click the Search icon (magnifying glass) in the bottom left-hand corner and type "cmd" into the search bar.

2. Select the Command Prompt app - it will be at the top of the list of search results as the best match.

3. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

Windows 7 & Vista

1. Open the Start menu by clicking the Windows icon at the bottom left-hand corner of the screen.

2. Type "cmd" in the search bar at the  bottom of the menu.

3. Click cmd found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows 8

1. Move the mouse to the right-hand corner of the screen to make the vertical menu bar (charm bar) appear. Click Search.

2. Type "cmd" in the search bar and hit the Enter key on your keyboard.

3. Click cmd that found in the search results for Programs.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you like to ping and then hit the Enter key on your keyboard. Wait for the ping results.
 

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the traceroute results.

Windows XP

1. Click the Start button in the bottom left-hand corner of the screen.

2. Click the Run option in the right-hand column.

3. Type "cmd" in the text box and then hit the Enter key on your keyboard.

4. A black box with a flashing cursor will open; this is the Command Prompt.

For Ping Test, type "ping" and then hit the Space bar on your keyboard. Type in the address you'd like to ping and then hit the Enter key on your keyboard. Wait for the ping results.

For Traceroute Test, type "tracert" and then hit the Space bar on your keyboard. Type in the address you'd like to trace and then hit the Enter key on your keyboard. Wait for the tracert results.

Please submit your issue here or you can WhatsApp us at 03-9543 3838.

Netflix is available to IPTV customers on the Ultra Box and Ulti Box. Non-Ultra Box customers will not be able to access Netflix on CH741. Please upgrade to the Ultra Box/Ulti Box to access Netflix on the Ultra Box.

Your Disney+ Hotstar will be paused and will only resume once your Astro service is reinstated. 

1. Please standby computer/laptop to access to the internet and connection must be via (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 or www.tplinkwifi.net and below page will appear.

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your router previously, the password may be different

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.
 

5. From the top menu, choose Basic and then click Wireless tab on the left menu to access to below screen.

6. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

7. You may change the Wireless Network Name (SSID) and the Password to follow your preferences, then click "Save"  for the changes to take place.

Please reconnect to the new wireless name with the new password once completed.

STEP 1
Please wait while your Astro box initializes.



STEP 2
Select your preferred language.



STEP 3
Navigate to Next and press "OK".



STEP 4
Select Auto as the Video Resolution.



STEP 5
Navigate to Next and press "OK".



STEP 6
Navigate to Confirm and press "OK" to confirm your selection if you are able to read the texts on screen properly.
Otherwise, navigate to Cancel to revert to the previous settings.



STEP 7
Select IPTV Plug & Play (self-install) as the box operating mode.



STEP 8
Navigate to Next and press "OK".



STEP 9
Select your preferred connection.
For connection via Wi-Fi, proceed to STEP 10.
For connection via LAN Cable, proceed to STEP 16 once you are connected.



STEP 10
Please wait while your Astro box searches for available Wi-Fi networks.



STEP 11
Navigate to your preferred Wi-Fi network and press "OK".



STEP 12
Please enter the password to connect to the Wi-Fi network.



STEP 13
Navigate to Done to continue.



STEP 14
Please wait while your Astro box connects to the internet.



STEP 15
Navigate to Yes to allow your Astro box to connect to this network automatically.
Otherwise, navigate to No.
Proceed to STEP 17 for the next step.



STEP 16
Navigate to Next and press "OK". 



STEP 17
Your box's connection status will be displayed.
Navigate to Finish to complete the setup.

To cancel your Multiroom (Smart TV) subscription, please call us at 03-9543 3838.

Discover thousands of movies and series you'll love, and we are continuously expanding. If you would like to enjoy more movies on top of your current subscription, press the Home button and select On Demand. Use the arrow keys to scroll to Store. Pick and choose to rent any movie for up to 48hours.

Step 1: Download the My Astro app from either the App Store, Google Play or HUAWEI AppGallery.

Step 2: Sign in with your Astro ID.

Step 3: Select "Rewards" on the home screen to get started.

Watch this tutorial to learn how to create your Astro ID.

No, Astro Fibre is only available for a 24-month contract period upon sign-up.

Wider WiFi coverage:

-All areas across the house will enjoy optimal coverage with multiple Mesh WiFi units located in areas with sub-optimal coverage to form a larger WiFi network.

Stable connection;

-Consistent coverage of optimal WiFi signal will ensure a stable connection as the Mesh unit will automatically connect your devices to the strongest WiFi signal around your house.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.
you may have to get your hands a little dirty.
 

1. Try loading the site on a different device.
   • Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.
   • If the website doesn't load on another device, the problem is either with the network or the website itself.
2. Restart your computer.
   • ​​Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.
3. Try loading the site in a different browser.
   • There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.
4. Temporarily disable your antivirus program.
   • Your antivirus software may be interfering with your ability to load certain websites.
   • Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.
5. Reset your modem and router.
   • Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.
6. Check your computer's date and time settings.
   • If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.
   • Check your computer or mobile device's clock to make sure that it is  set to the correct time and date.
7. In the event the problem persists, please provide below details for further escalation:
   • List of websites effected.
   • Run the Speed Test  via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.
   • Run the Traceroute Test - Please click here for Traceroute Test guideline.
   • Run the Ping Test -  Please click here for Ping Test guideline.
   • Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

1. Tune to Astro channel 200 - select "Add-Ons"

2. Select the option for Monthly Subscription

3. Send the WhatsApp code as per displayed on the TV screen

Please call our Customer Contact Centre or WhatsApp "DH Help" at 03 9543 3838 to cancel your Disney+ Hotstar 3-months add-on pass with Astro. 

STEP 1  

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3  

Navigate to Display and press "OK".

STEP 4    

Navigate to Resolution and press "OK".

STEP 5    

Navigate to your preferred selection and press “OK”.

STEP 6    

Select Yes, continue and press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

Advance payment can be made via credit/debit card or online banking.

Customers with a Movies subscription via Movies, Premium 1, Premium 3 and Platinum packs will be able to access Disney+ Hotstar on the Ultra box.

Alternatively, customers can add on the 3-month Disney+ Hotstar pass for RM54.90. Subscribe to Disney+ Hotstar via astro.com.my/Disney.

For more support and options for your subscription, please WhatsApp us at 03 9543 3838 and type DH Help. Alternatively, you may visit astro.com.my/Disney for more information.

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2  

Navigate to Settings.

STEP 3    

Navigate to Parental Control and press "OK".

STEP 4    

Please enter your PIN (Default PIN is 0000).

STEP 5    

Navigate to your preferred category to block and press "OK".

1. Unifi netis brand

The following shows an Interface based on Unifi router

1. Launch Web Browser and enter the default's gateway's IP address (192.168.1.1) in the address bar.

1. Enter Username and Password.
   1. Username = tmadmin
   2. Password = Adm@xxxx (xxxx refers to last four digits of MAC address)

1. Choose WLAN -> wlan0 (2.4GHz) Basic Setting. Note down on SSID.

1. Choose WLAN -> wlan1 (5GHz). Compare SSID with previous SSID.

1. If SSID for wlan0 (2.4GHz) and wlan1 (5GHz) are the same. Change wlan1 (5GHz) SSID by adding number 5(i.e. ifuni_5G) to differentiate from 2.4 GHz. Click Apply Changes.

Note: Connection to Wi-Fi may be temporarily loss while the changes is updated.

You can request for a password reset by clicking on "Forgot My Password' at the login page.

Redemption should be done by the account holder. However, if the account holder is unavailable, immediate family members can make the redemption provided that the account holder has given them the permission to redeem using his account credentials.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.

1. Try  loading the site on a different device.

  Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.

  If the website doesn't load on another device, the problem is either with the network or the website itself.

2. Restart your computer.

  Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.

3. Try loading the site in a different browser.

  There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.

4. Temporarily disable your antivirus program.

  Your antivirus software may be interfering with your ability to load certain websites.

  Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.

5. Reset  your modem and router.

  Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.

6. Check  your computer's date and time settings.

  If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.

  Check your computer or mobile device's clock to make sure that it is set to the correct time and date.

In the  event the problem persists, please provide below details for further  escalation:

  i. List of websites effected.          

  ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.  

  iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.          

  iv. Run the Ping Test -  Please click here for Ping Test guideline.

 Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

Please use your Astro ID that was registered with your Astro Fibre subscription to log in to the Astro Fibre App.

What is beIN SPORTS CONNECT?

beIN SPORTS CONNECT is the ultimate live streaming sports service that provides you with access to global sporting events both LIVE and on-demand such as major European football leagues and over 3,000 hours of live tennis via Astro's Ultra Box, Ulti Box, mobile app or web.

How do I access the beIN SPORTS CONNECT app on the Ultra/Ulti Box?
On the beIN SPORTS CONNECT mobile app:
Step 1: Open the "beIN SPORTS CONNECT" app and go to your Profile
Step 2: Select "Sign in with Astro" and log in with your Astro ID
Step 3: Go to "Settings" and select the TV Login option
Step 4: A QR code scanner will appear.

Follow the steps below to pair the mobile app with your TV screenOn the Astro Ultra/Ulti Box:
Step 1: At Astro Home, go to the app rail and select "beIN SPORTS CONNECT"
Step 2: Go to the Profile icon at the top of your screen and click "OK"
Step 3: A QR code will be presented on your screen. Use the in-app QR code scanner on your mobile device to scan the QR code
Step 4: Your TV screen will refresh automatically and you will be able to enjoy the beIN SPORTS CONNECT app on your TV!

Who is entitled to access the beIN SPORTS CONNECT app on the Ultra/Ulti Box?
Only Astro customers with the Sports subscription as part of their Astro TV Pack (Bundle or add-on) will be able to enjoy the beIN SPORTS CONNECT app on their Ultra/Ulti Box. For further enquiries, please WhatsApp "Get beIN" to our Customer Contact Center at 03-9543 3838.

What are the content available in the beIN SPORTS CONNECT app?
Customers can enjoy major European football leagues, over 3,000 hours of live tennis and other global sporting events LIVE and on-demand on the app. You may check out the complete list of competitions available on the app here: beIN SPORTS CONNECT | Live Leagues and Competitions | LaLiga, Serie A, Ligue

Can I stream on more than one device at the same time?
No, you can only stream the beIN SPORTS CONNECT app on one device at a time.

How many devices can I use to watch beIN SPORTS CONNECT?
You can have up to five (5) devices registered to your account at any given time. However, you can only stream from one (1) device at a time.

Can I download content for offline viewing?
Unfortunately, downloading of content is not a feature that is currently available.

Are subtitles or dubbing available for the content on beIN SPORTS CONNECT?
Unfortunately, subtitles and dubbing options are currently not available.

How can I subscribe to beIN SPORTS CONNECT via Astro?
The beIN SPORTS CONNECT app is not available as an add-to-bill option. Please visit www.product.astro.com.my/tv to sign up to one of our TV Packs with the Sports subscription.

Can I access the beIN SPORTS CONNECT app outside of Malaysia?
No, you will not be able to watch beIN SPORTS CONNECT content outside of Malaysia as the app is geo-blocked for each country.

How do I register for an Astro ID?
Download the beIN SPORTS CONNECT app > Select "Login with Astro"> Click "Do not have an Astro ID? Click here".

Can I update my email address/mobile number for my Astro ID?
Yes, please visit Astro's Self Service Portal via myastro.astro.com.my to update your email address or mobile number.

I have forgotten my password; what should I do?
Step 1: Click "Log in" and click "Forgot my password"
Step 2: Enter your email address and click "Submit"
Step 3: An email will be sent to your registered email address with further instructions on how to reset your password

How do I unlock a locked user account?

You may contact Astro's Customer Service by:

1. Submitting a feedback form here: https://support.astro.com.my/feedback-form
2. Reaching out to us via WhatsApp by typing "Hi" at 03-95433838 for assistance

ransfer of Equipment Ownership

A request to transfer the equipment’s ownership from the existing account holder to a new account holder. ‍

Note: Transfer of Equipment Ownership is not applicable for IPTV and NJOI account.

Merge of Equipment

A request from the account holder to merge the equipment from two different accounts into one account, provided the equipment must be within the same service address and registered under the same accountholder’s name.

Split of Equipment

A request from the account holder to split the equipment from one account to two different accounts and registered under the same account holder’s name.

You may click here to Login and proceed to secure your Astro ID by linking it to your Astro account. If you do not have an Astro ID, please follow the steps in below to create one. You may also choose to log in or create Astro ID with your social accounts (eg. Facebook, Google and Apple).

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

‍

STEP 2

Navigate to Settings.

STEP 3

Navigate to Menu Language and press "OK".

STEP 4

Navigate to your preferred language selection and press “OK”.

No, the Mesh WiFi add-on with Astro Fibre is available as subscription service and will not be tied to any device contract.

Service will resume within 3 hours after payment is made.

You may utilise your credit balance to offset future billing on your Astro account, or contact us here for further enquiries.

If your existing Netflix account is linked with your Astro subscription, your Netflix account will resume on the previous method of payment. If you linked a new Netflix account with your Astro subscription, cancelling Astro service will also cancel your Netflix account.

No, eligible customers will not be charged for this speed upgrade. Your speed plan will be upgraded automatically for 24 months, depending on your subscription. After the FREE speed upgrade period, your Astro Fibre plan will return to its regular speed.
 

Astro sends regular payment reminders to customers via SMS until their current charges have been paid. However, we encourage customers to pay their bill as soon as possible to avoid disconnection of Astro service. Please reach out to us here if you require more information about payment reminders or to change your contact details.