The new packs come with 200 hours of Cloud recording by default. If your current recordings exceed 200 hours, the system will delete the exceeded hours once your package has been changed, starting with the oldest recordings first.  

If you would like to retain the previous recordings which exceed 200 hours, you may opt for a selection of 400 or 1500 Cloud Recording hours at a chargeable rate of RM12 or RM15 per month (excl. govt tax) respectively. Or else, you may subscribe to the Platinum pack which comes with complimentary access to 1500 hours of Cloud Recording.

You can proceed with below BTS if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to Diagnostics and press “OK”.

STEP 5

Refer to the signal strength on your screen.

If it is 65 or higher, please take the screenshot and submit your feedback form.

If it is below 65, please go to Step 6.

STEP 6

Switch off the power for your box and  make sure that the adapter’s power light is off.

STEP 7

Unscrew the satellite cable from the box  and pull it out.

STEP 8

Plug the satellite cable back into the  box and screw it back securely.

STEP 9

Switch on the power for your box and make sure that the adapter’s power light is on. Please wait for 5 minutes.

STEP 10

Turn on your box. You should no longer be experiencing this issue.

If issue persist, please submit the issue on our Feedback Form with error details and attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized  Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

If you are interested to upgrade your box, you can do so via Astro's retailers or online as follows:

I. Visit https://hub.astro.com.my/#5

II. Select `Box Upgrade` and log in with your Astro ID

III. Select the box you would like to upgrade

Yes, you may terminate the service. However, an early cancellation fee will be applied for terminations/cancellations within 24 months. Please refer to the Astro Fibre's cancellation details.

Please switch your current subscriptions to our new Astro packs to subscribe to Multiroom (Smart TV). To sign up, WhatsApp “SWITCH” to 03-9543 3838 and an agent will assist you. 

Find out more of our new packs at https://product.astro.com.my/tv

Any Astro GO compatible device (mobile/tablet/PC) and Multiroom Smart TV* compatible TVs will benefit from Astro GO+. 

It will take around 10 to 15 minutes before you are able to view your purchase.

The Multi-user Profile feature allows customers to create individual profiles within their Astro Box and Astro GO with the following personalisations:

• Personalised Recommendations
• Continue Watching 
• Watch List
• Last Viewed Channel
• Favourite & Blocked Channels

The MUP feature is a great way to allow individual users to tailor personal Astro experiences whilst using a shared device (e.g.: Astro Box) in the household, providing them with better personalised recommendations and encouraging better content discovery.

Click here to find out more on this new feature and how to use it!

Please note that only one Disney+ Hotstar access is bundled to each Movies Pack subscription which allows two concurrent streams on Disney+ Hotstar.

Your bill statement will include details of your monthly subscription charges; e.g. charges for your chosen Astro packages and Broadband service. It will also show the time period of which your first bill will cover, as well as indicate how much the total charges are and when the payment due date is.

You may proceed with the following troubleshooting steps and it shouldn't take you much longer than 15 minutes.

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN  cable to the Black port at D-Link Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://dlinkrouter.local./ and below  page will appear. (These are the defaults and if you have done a  configuration on your router previously, the password may be different)

Username: admin

Password: (Leave the field blank)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, click Settings and then choose Wireless.

6. Below screen will appear to configure the wireless setting. Since this is a dual band router, you will have 2 Wi-Fi Names (SSID); i.e. 2.4GHz and 5GHz.

i. For 2.4GHz setting, click Advanced Settings to display more available options.

ii. To change the channel, click the drop-down arrow for Wi-Fi Channel, then select your desired channel.

Choose between 1 to 13 (Suggested channels : 1,6,11). Click Save for the changes to take place.

The router will auto reboot and connection will re-establish after few minutes.

iii. Next, for 5GHz setting, click Advanced Settings to display more available options to make changes on the wireless channel for 5GHz.

iv. Click the drop-down arrow for Wi-Fi Channel, then select your desired channel from the selection.

v. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few  minutes.

1. Please standby computer/laptop to access to the internet and connection must be via (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 or www.tplinkwifi.net and below page will appear.

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your router previously, the password may be different

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.
 

5. From the top menu, choose Basic and then click Wireless tab on the left menu to access to below screen.

6. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

7. You may change the Wireless Network Name (SSID) and the Password to follow your preferences, then click "Save"  for the changes to take place.

Please reconnect to the new wireless name with the new password once completed.

Your Astro account number is a 10-digit combination 
E.g: 08XXXXXXXX

We are working with the Sony team to ensure you will be able to enjoy these 4K UHD channels soon. We will keep you posted once these channels are available to you!

No there will not be any penalty.

For the Multiroom subscription on a box setup, if your subscription is within the 24-month contractual period. Then a pro-rated penalty of RM600 will be applied for any Astro box except for Ultra Box, which the penalty will be RM1,000.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/ laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/ laptop].
2. You may open any web browser such as  Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)

Username: admin
Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the  configuration.

i. On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab.

ii. Please ensure Wireless RF Mode is Enabled.

iii. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

iv. Click Submit. Router will auto reboot and connection re-establish after few minutes.

No, your rewards cannot be transferred to another person or exchanged for cash.

Your existing contracts and corresponding rewards including but not limited to discounts/rebates will be removed with no penalty applied and replaced with the new contracts associated with the new packs. Exception applies to Disney+ Hotstar (3-Month Pack) and Multiroom campaigns in which remaining contract durations will be brought over if the subscription is continued or penalty will be applied upon discontinuation of said subscriptions.

You may proceed with the following troubleshooting steps and it shouldn't take you much longer than 15 min

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Yellow port at Tplink Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to tplinkwifi.net and to access to below login page. Type the Username and  Password, then click "Login".

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your  router previously, the password may be different.

For example, below is the login details of the above router:
 

Username: admin

Password: TIMECE24
 

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, choose Advanced and click the Wireless tab on the left menu. Then, select Wireless Settings from the sub menu. Below screen will appear for 2.4GHz selection.

i. Please ensure to tick Enable Wireless Radio function.

ii. To change the channel, click the  drop-down arrow for Channel, then select your desired channel.

Choose between 1 to 13 (Suggested  channels : 1,6,11). Then, click "Save" for the changes to take place.

iii. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

iv. Next, select 5GHz to make changes on the wireless channel for 5GHz.

v. Click the drop-down arrow for Channel, then select your desired channel from the selection.

vi. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

Please follow the steps in Q5, then continue with the steps below:

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

STEP 1
On your remote, press the Home button and the Home Page will be displayed your screen. 



STEP 2
Navigate to SETTINGS.



STEP 3
Navigate to Profile Selection on Startup and press “OK”.



STEP 4
Navigate to your preferred selection and press “OK”.



STEP 5
Navigate to Save and press “OK”.

Yes, a charge of up to RM20.00 may be imposed upon reconnection.

To reconnect your Astro account, please check your Account status, Bill Summary and pay on Astro Quick Pay. Your disconnected services will resume within 1 hour after you have paid your "Total Overdue Charges"

If the bill has been paid, there will not be any additional service tax charge. However, if the bill has been issued by Astro but has not been paid, then the 8% Service Tax will be reflected in the next bill with adjustments on the new tax rate for services rendered from 1st March onwards.

Example:
Bills issued on 15th February will be charged the 6% SST. Customers will see proration for 8% from 1st – 14th March in the next bill issued on 15th March 2024. If you have fully paid your February bill before 1st March, the Service Tax will remains at 6%. You will be able to see the adjustment reflected in your next bill.  
 

No, Pay-Per-View is no longer available in CH200.

You can proceed with below troubleshooting if the weather is good. Ortherwise, you may try again later.

STEP 1
On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.


STEP 2
Navigate to SETTINGS and press “OK”.


STEP 3
Navigate to STB DIAGNOSTICS and press “OK”.


STEP 4
Refer to the signal strength % shown on the top left of your screen.
If it is 65% or higher, please go to WhatsApp to receive further help.
If it is below 65%, please go to STEP 5.


STEP 5
Switch off the power for your box and make sure that the adapter’s power light is off.


STEP 6
Unscrew the satellite cable from the box and pull it out.


STEP 7
Plug the satellite cable back into the box and screw it back securely.


STEP 8
Switch on the power for your box and make sure that the adapter’s power light is on.
Please wait for 5 minutes.


STEP 9
Turn on your box. You should no longer be experiencing this issue.
If issue persist, please attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized Dish
 If issue persist under a centralised satellite dish, please refer to your respective Building Management before contacting our agents.

For customers whose sign-up speed is 50Mbps, 100Mbps or 500Mbps, you will get to enjoy your upgraded speed of 100Mbps/500Mbps/800Mbps for 24 months.
 

Please refer to the Welcome Card inside the Plug & Play Box package and scan the QR code. You may choose to watch either the self-installation video or the Augmented Reality (AR) Installation Video to activate your Plug & Play Box. You can also download the Installation Guide from the Astro Get Started Page.

Please install and activate your Plug & Play Box within 7 days of receiving your Plug & Play Box and Astro SIM card. If you are unable to activate your Plug & Play Box within 7 days, the Plug & Play Box will be automatically activated by Astro on the 8th day.

The billing and warranty of the Plug & Play Box shall begin on the same date of which the Plug & Play Box is activated.

In the event that you have ordered more than one (1) Plug & Play Box, please refer to the Astro SIM card letter (included with the Astro SIM card delivery) to match the right Astro SIM card to the respective Plug & Play Box. Each Astro SIM card has been paired with a specific Plug & Play Box, thus the correct matching of box and SIM card is required for it to work properly.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Preferences and press "OK".

STEP 3  

Navigate to Language and press "OK".

STEP 4    

Choose your language preferences and press "OK".

STEP 5  

Select Yes, continue and press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

At this point in time, the Disney+ Hotstar app on the Ultra or Ulti Box does not support Dolby audio. We are working to enable this in a future update. 

Yes, the subscription will be reflected on all your set-top box provided they are registered under our Multiroom service.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Audio Delay and press "OK".

STEP 4

Navigate to your preferred selection and press “OK”.

By keying in the 10-digit account number, Astro will be able to provide better self-service options, as it allows Astro to customise automation options based on the needs of each customer's account.

You can proceed with below troubleshooting if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4

Refer to the signal strength % shown on the top left of your screen.

If it is 65% or higher, please take the screenshot and submit your Feedback Form.

If it is below 65%, please go to Step 5.

STEP 5

Switch off the power for your box and make sure that the adapter’s power light is off.

‍STEP 6

Unscrew the satellite cable from the box and pull it out.

STEP 7

Plug the satellite cable back into the box and screw it back securely.

STEP 8

Switch on the power for your box and make sure that the adapter’s power light is on.

Please wait for 5 minutes.

STEP 9

Turn on your box. You should no longer be experiencing this issue.

‍

If issue persist, please submit the issue on our Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

‍

Centralized Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.