Astro continuously reviews its product propositions to ensure we can provide the best customer experience for all our subscribers. We have discontinued the 50% multiroom in order to allow our Astro subscribers with a subscription fee of RM100 or more to only pay a standard RM49.99 (with box setup)  to enjoy the Multiroom experience on an Ultra or Ulti Box.

We apologise for any inconvenience.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

No, there will be no additional charges to access Liga Malaysia.

If band steering is enabled, you do not need to worry about which frequency band that your devices are connected to because the WiFi router will make the assessment and direct each device to appropriate frequency band.

However, it is important to note that quality and signal strength are not guaranteed due to unpredictability given that it is completely up to the connected devices and the WiFi router to intelligently decide on which band to connect.

STEP 1
Switch off the power of your box and make sure that the adapter’s power light is off.


STEP 2
Unplug the HDMI cable from your TV and plug it back in securely to other available HDMI port.


STEP 3
Switch on the power for your box and make  sure that the adapter’s power light is on.
Please wait for 5 minutes.


STEP 4
Turn on your box. Do select the correct TV input.
You should no longer be experiencing this problem. 
​

Yes, you can restrict programmes based on the age rating by going to "Settings” > “Parental Controls & Profiles” on your Astro Box and Astro GO app. Alternatively, you may also create a Kids Profile that provides security with a 4-digit PIN to exit and accessibility to kids-friendly channels and On Demand content only.

The PVR comes with a 12 months warranty from the date of activation.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Navigate to IP Diagnostics and press "OK".

STEP 5    

IP Diagnostics information will be displayed.

This issue occurs because  your TV does not support the higher resolution.
 

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.
 

STEP 2

Switch on the power for your box and make sure that the adapter's power light is on.
 

STEP 3

Press the standby button repeatedly after switch on the power.

The Startup Options screen will appear on your TV.

STEP 4

Press "987" to access the Advanced Startup Options menu.

Then, press "1" to initiate a reset setting.

STEP 5

Press "OK" to confirm restore to factory setting.

STEP 6

After the factory setting is restored, TV will turn blank.

Please wait until the box completes initiate setup.

STEP 7

Press "1" to initiate Linux download on the software.

STEP 8

Once completed, the following screen will appear on your TV.

Refer to Installation Setup guide here to complete the setup.

The new packs and access to Netflix on the Ultra Box and Ulti Box is available for Astro IPTV customers.

Starting 12 December 2023, users have to use their registered email address, mobile number or a social account (Facebook, Google or Apple) to log into any of Astro's digital platforms, including My Astro, Astro GO and Astro's official website. Usernames as an Astro ID is no longer available. This change was made to ensure details linked to your Astro account are always updated and to improve the overall user experience on our platforms.

Advance payment is only applicable to Astro TV pack purchases. If you subscribe to an Astro Fibre+TV bundle, only one month of your TV subscription fee (excluding tax) is required to be paid upon sign-up. The full tax amount and the first-month subscription fee for Astro Fibre will be paid on your first month's bill.

The service tax rate for Astro Pay TV will be increased from 6% to 8%. The service tax for Astro Fibre, which falls under the category of telecommunication service, will remain at 6%.

No. However, if you cancel your Astro Pay TV services but resubscribe at a later date, your duration (year) with us will reset to zero and restart according to your new activation date. Your Astro Rewards tier will reset to Magenta.

STEP 1

Identify your remote control:

a)   Remote control with Astro logo at the bottom of the remote, proceed to STEP 2.

b)   Remote control with Astro logo at the top of the remote, proceed to STEP 4

‍

STEP 2 (Astro Logo at the bottom of the Remote)

On your remote, press the “set tv” button and set tv instructions will be displayed on top of your screen:

‍

STEP 3

Follow the steps appear on the TV screen to sync your Astro remote and complete the setup.

‍

STEP 4 (Astro Logo atthe top of the Remote)

Press and hold “tv input” key on bottom left of the remote for 3 seconds until the LED blinks twice.

STEP 5

Enter the 2-digit TV Code of your TV Brand and the LED will blink twice:

‍

STEP 6

Try out the TV controls (TV Standby or adjust Volume) to check if they are working correctly.

‍

STEP 7

Press ok and wait for the LED to blink twice to save the settings.

STEP 1  

On your remote, press the HOME button.

STEP 2  

Navigate to SETTINGS  icon and press "OK".

‍

STEP 3    

Navigate to Manage Satellite Frequency and press “OK”.

‍

STEP 4  

Choose to Update Satellite Frequency and press “OK”.

‍

STEP 5    

Choose "Confirm" to continue Satellite Frequency Update and press “OK”.

‍

STEP 6  

Satellite Frequency Update progress screen will be displayed.    

The updates will take approximately 20 minutes.

STEP 7

The status will be displayed once update is complete.    

After service termination of your Astro Fibre service, we will call you via your registered mobile number (up to 3 times over 3 days) to schedule an arranged pick-up by one of our Astro agents. Our agent will then come to your doorstep, dismantle the devices for you and retrieve them.  

Note: Upon termination of your service, customers are required to return their old Astro Fibre devices to Astro. Failure to do so will incur a fee of RM200 (WiFi Router), RM500 (Fibre Modem) and RM200 (Mesh WiFi Unit - if applicable) for each unit. All prices stated are exclusive of Govt. tax.

You require at least two devices to form a Mesh WiFi network which are Astro Fibre WiFi router and a Mesh WiFi unit.

The Mesh unit will link to the WiFi router to form the Mesh WiFi network. You may connect up to 5 Mesh WiFi units for optimal WiFi coverage in your home.

When Band Steering is disabled, you will see two separate WiFi SSID based on its frequency bands. Example:

i.SSID: SSID2G, Password: 1234567

ii.SSID: SSID5G, Password: 4567890

*WiFi SSID (Service Set Identifier) is the name of your wireless network, also known as Network ID. It is viewable to anyone with a wireless device within reachable distance of your network.

You will require HD-PVR service in order to subscribe for a PVR. This service is included in all Starter Pack, Value Pack, Super Pack Lite, Super Pack and Super Pack Plus subscriptions.

To be eligible, you'll need to be an Active Astro Pay TV customer with a valid Astro ID.

An Active Astro customer refers to a subscriber of the Astro Service, whose account is current and active with no outstanding payments due and who has not breached the Astro subscription agreement nor given any instructions to terminate and/or suspend his/her subscription to the Astro Service.

Each account you hold is entitled to one (1) tier status based on the longest active smartcard.

Yes, starting 9 November 2021, these new packs will be Astro's default offering.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Master PIN and press “OK”.

STEP 4

Please enter your PIN (Default PIN is 0000).

STEP 5

Please enter your new PIN.

STEP 6‍

Please re-enter your new PIN to confirm.

STEP 7

Your PIN successfully changed when this  screen appears.

When using our One Time Payment (OTP) method, you may register more than one credit card per account. However, a single card account can only be used for a maximum of three accounts for OTP transactions.

When using our auto-debit facility, you can only register one card with Astro. Any subsequent card registrations will override the current one.

Each Astro customer is entitled up to 4 smart devices to be registered including mobile, laptops, tablets and Smart TV per household.

If you have maximised the registered device, you will be able to see the list of all your current registered devices on your mobile screen. Please remove any one device to allow the current Smart TV device to be included.

Do note that only 1 Smart TV device is allowed at any point in time.

You may contact Astro's Contact Centre (03 - 9543 1543) to process the cancellation.

The Mesh WiFi device(s) needs to be returned upon service termination via an arranged pick-up by our installers.

Please provide your primary mobile number via My Astro Portal, or send it to one of our platforms found here.

Note:

• Any changes of contact details to be requested by account holder only.
• Only account holder's contact to be updated as primary mobile number in the system.

Astro GO is a companion app that is complimentary for all Astro subscribers and allows up to 2 users to stream at the same time. 200 hours of cloud recording* come complimentary with your Pay TV subscription. 

Astro GO+ is an add-on service that enables up to 4 users to stream Astro GO and/or Multiroom Smart TV** at the same time. The amount of cloud recording storage will also be increased to 1500 hours. 

 *Cloud recording hours are shared across your Astro Box, Astro GO and Multiroom Smart TV 

** Provided that you have a Multiroom Smart TV subscription

I am sorry you can't. While we understand the value customers see in choosing their preferred service/pack individually, the packaging of channels/services in the new packs are necessary for us to offer content/services at an affordable price to our customers.

STEP 1

‍

Try to change channels on your Astro  remote.

INDICATOR: LED blinking 3 times / NO LED blink

SOLUTION: Replace new battery

Proceed to Step 2.

‍

INDICATOR: LED blinking 1 time

Confirm it's not your Astro remote faulty, let's proceed to Step 3.

‍

STEP 2

If issue remain after the battery replacement, this might be due to a faulty Astro remote.

Try changing the channel manually directly from the box front panel (If any).

If it's working, you might need to  replace your Astro remote.

You may walk-in to our nearest Customer Service Center for the replacement.

STEP 3

You need to refresh the box setting by initiate manually from box front panel.    

Refer to Refresh Box setting Guide steps here.

Firstly, you would have to retrieve your email address/mobile number. Please follow the steps in Q7 in order to do so. Then, follow the steps in Q5 and Q6 to check or update your contact details. Please use your updated email address or mobile number as your Astro ID to log in moving forward.

Note: Only Astro customers whose Astro ID is linked to their subscription can retrieve their Astro ID this way. Otherwise, you would need to create a new Astro ID.

STEP 1    

On your remote, press the ... button and the Channel Guide page will be displayed on your screen.

STEP 2    

Select the channel you would like to remove as favourite and press "OK".

STEP 3  

Select "Remove from Favourite" and press "OK".

STEP 4    

You are successfully removed the channel from favourite list when this screen appears.

1. Tune to Astro channel 200 - select "Add-Ons"

2. Select the option for Monthly Subscription

3. Send the WhatsApp code as per displayed on the TV screen

Yes, existing Astro customers can subscribe to all Astro & Broadband offerings. 24 months contract will be renewed upon signing up for broadband.

You can proceed with below troubleshooting if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4

Refer to the signal strength % shown on the top left of your screen.

If it is 65% or higher, please take the screenshot and submit your Feedback Form.

If it is below 65%, please go to Step 5.

STEP 5

Switch off the power for your box and make sure that the adapter’s power light is off.

‍STEP 6

Unscrew the satellite cable from the box and pull it out.

STEP 7

Plug the satellite cable back into the box and screw it back securely.

STEP 8

Switch on the power for your box and make sure that the adapter’s power light is on.

Please wait for 5 minutes.

STEP 9

Turn on your box. You should no longer be experiencing this issue.

‍

If issue persist, please submit the issue on our Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

‍

Centralized Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

The matches will be available on the channels Astro Arena Bola (CH803) and Astro Arena Bola 2 (CH804), On Demand and Astro GO.

Further details on pricing, billing and availability will be confirmed in coming months. Look out for more details and register your interest via https://astro.com.my/Netflix

Yes, as long as it is compatible with Open Mesh standards and Astro Fibre equipment. However, Astro will not be responsible for managing or configuring the device. For the optimum WiFi experience, please pair your Astro Fibre with Astro's Mesh WiFi.

The notification you receive will depend on the payment method you choose:  
(i) My Astro Portal: e-receipt will indicate payment confirmation.
(ii) IVR:  Payment status will be notified over the IVR and an SMS notification will be sent for successful transactions.
(iii) SMS: Payment status will be notified via SMS.
(iv) Call: Payment status will be notified via SMS.
(v) Customer Service Centre: Physical receipt will indicate payment confirmation.

No, Ultra Box is only available for Entertainment Pack and above only.

In the new bill layout, there are three tax indicators for customer to refer: S1 (8%), S2 (6%), and N (non-taxable item). Each item list will be marked in accordance with the tax indicator below:


 

Yes, you will need to pay additional RM25 per remaining contract months per unit on top of the standard Broadband penalty fee should you terminate the contract within 24 months.

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

Multiroom (Smart TV) is a secondary subscription that allows you to enjoy your favourite Astro shows instantly in different rooms at the same time on your Smart TV. Subscribe to Multiroom (Smart TV) at RM29.99 per month (excl. any govt. tax), and simply download the Astro app on your second TV-screen and connect to your home Wi-Fi to stream.

Connect your Ultra Box/Ulti Box today and get the full value for your subscription. We believe we can provide you the best entertainment experience in Malaysia, and it all starts with connecting your box to the internet.

Want to enjoy these features for free?

• Continue watching Astro even when it’s raining.
• Binge-watch and catch-up to 110,000 videos on-demand from Malaysia, Hollywood, Korea, China, Bollywood and more anytime.
• Create multiple profiles in your house to enjoy a personalized Astro experience, with shows recommended to you based on your interest. There is a Kids-friendly version for your little ones as well.
• Rewind, pause and fast-forward shows and matches so that you will never miss another moment.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Scroll to Network Settings and press "OK". Select New Wi-Fi Connection and press "OK".

‍

STEP 4

Select your Wi-Fi network and press "OK". Please enter the password to connect to your network.

STEP 5

You have successfully connected when this screen appears.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Audio and press "OK".

STEP 4

Navigate to your preferred selection and press “OK”.

Visit https://product.astro.com.my/box or check out our user guide for a quick and easy way to get started!