You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

Your monthly bill of the previous and new pack will be prorated. This will be reflected into your bill accordingly.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the blue port in Cisco Router and direct to computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

‍

‍

4. Type the Username and Password as below. Then click "OK". (These are the defaults, if you have done previous configuration on your router the password may be different).

Username: admin

Password: admin (or time123)

5. Click "OK" when a Warning prompt that says,” Using this advanced utility to change your router settings could disable your network” appears. Below display will appears.

6. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

7. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

8. Click Wireless Security to view the security settings of your wireless network. Take note of the Security Mode and the Passphrase.

For the example below, the Security Mode used is WPA2/WPA Mixed Mode.

The Wireless name is called Network Name (SSID) and the Passphrase is your wireless password.

‍

9. Now that you have the Wireless name and Password, you are ready to connect your wireless computers and devices to the network.

10. You may change the Network Name (SSID) and the Passphrase to follow your preferences and please ensure save the changes made. Please reconnect to the new wireless name with the new password once completed.

‍

Please ensure to put your box on standby mode to refresh the signal.

a. Using IVR

1. Dial 03-95433838 and select you preferred language.
2. Select Account Related.
3. Select Technical Assistance.
4. Select Refresh Smartcard.

b. Using MyAstro web

STEP 1
Go to https://myastro.astro.com.my/ in your web browser.



STEP 2
Key-in your Email / Mobile number and password. Then, press LOG IN.



STEP 3
Click on TV pack.



STEP 4
Choose Main Room for the Primary Box; else choose Multiroom (If any).



STEP 5
Click on "Refresh" to refresh signal on your box. 

For Main Box


For Multiroom


STEP 6
After tap the Refresh, below notification will be displayed as below.

For Main Box


For Multiroom


c. Using MyAstro App

STEP 1
Open myAstro App and click "Login".



STEP 2
Key-in your Email / Mobile number and password. Then, press "LOG IN".



STEP 3
Go to "Account".



STEP 4
Scroll down to "TV pack" and click on it.



STEP 5
Choose Main Room for the Main Box; else choose Multiroom (If any).



STEP 6
Tap on "Refresh" to refresh signal on your box. ​

For Main Box


For Multiroom


STEP 7
After tap the Refresh, below notification will be displayed as below.

For Main Room


For Multiroom

Currently, this change affects SMS bills only. Other SMSs such as (but not limited to) bill reminders, payment notifications, promotional SMSs or technical appointment reminders will still be sent to you if applicable.

You may still be using an older version of the Astro GO. To resolve this issue, please go to your respective app store and update your Astro GO app.

If you are still having issues, proceed to submit report via WhatsApp or Feedback Form.
 

No, you will not be charged 8% Service Tax for paper billing option.

Please note that your request to opt out has been processed, and payment for Disney+ Hotstar is not required. Your bill adjustment will be reflected in your next bill. 

This issue occurs because  your TV does not support the higher resolution.
 

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.
 

STEP 2

Switch on the power for your box and make sure that the adapter's power light is on.
 

STEP 3

Press the standby button repeatedly after switch on the power.

The Startup Options screen will appear on your TV.

STEP 4

Press "987" to access the Advanced Startup Options menu.

Then, press "1" to initiate a reset setting.

STEP 5

Press "OK" to confirm restore to factory setting.

STEP 6

After the factory setting is restored, TV will turn blank.

Please wait until the box completes initiate setup.

STEP 7

Press "1" to initiate Linux download on the software.

STEP 8

Once completed, the following screen will appear on your TV.

Refer to Installation Setup guide here to complete the setup.

Payment for Astro services will not increase. However, the Service Tax applicable will be increased from 6% to 8% and this will result in an increase in the total amount payable.

Regular (DTH) customers can watch Astro without an Internet connection. If you have selected Plug & Play setup option, a minimum speed of 10Mbps/device is required to enjoy a good HD viewing experience on Ultra/Ulti¯Box and 30Mbps/device for 4K UHD viewing on Ultra Box. However, if you have selected the Regular (DTH) option, the internet speeds above are recommended to enjoy a good viewing experience for On Demand and Astro Cloud services.

If you did not receive the recovery email or verification code, please make sure that:

1. You are inserting the correct email or mobile number you used to register for your Astro ID.
2. Check your junk mailbox or spam folder.  

To find out which email or phone number you have used to register your Astro ID, you may submit a feedback form. Kindly select feedback type "I have an enquiry/issue with Apps" choose "Astro GO" 
 

We will get in touch with you within 48 hours to solve your enquirie

To subscribe, WhatsApp "Smart TV' or call 03-9543 3838.

Astro customers on the previous packages (e.g. Family Pack, Starter Pack, Value Pack, Super Pack Lite, Super Pack or Super Pack Plus) will first have to sign up to our new packages on astro.com.my before they are able to sign up for Multiroom (Smart TV).

You can subscribe to Multiroom (Smart TV) here or via any of our sales channels.

Yes, penalty fee of RM200/Mesh WiFi will be imposed if customer fails to return the device(s). The courier company would make two attempts to retrieve the Mesh WiFi unit within a period of 30 days, failing which the penalty would be imposed.

1. Unifi netis brand

The following shows an Interface based on Unifi router

1. Launch Web Browser and enter the default's gateway's IP address (192.168.1.1) in the address bar.

1. Enter Username and Password.
   1. Username = tmadmin
   2. Password = Adm@xxxx (xxxx refers to last four digits of MAC address)

1. Choose WLAN -> wlan0 (2.4GHz) Basic Setting. Note down on SSID.

1. Choose WLAN -> wlan1 (5GHz). Compare SSID with previous SSID.

1. If SSID for wlan0 (2.4GHz) and wlan1 (5GHz) are the same. Change wlan1 (5GHz) SSID by adding number 5(i.e. ifuni_5G) to differentiate from 2.4 GHz. Click Apply Changes.

Note: Connection to Wi-Fi may be temporarily loss while the changes is updated.

No, the Service Tax is a tax payable entirely to the Government. Astro acts as a collection agent for the Government.
 

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

‍

STEP 2

Navigate to Settings.

STEP 3

Navigate to Menu Language and press "OK".

STEP 4

Navigate to your preferred language selection and press “OK”.

Your access to Astro GO will depend on the subscription pack that you are subscribed to. Not all shows/channels will be available on Astro GO as this depends on contractual rights with specific guidelines on the entitlement of these shows/channels. We are continuously working hard to make more content available on Astro GO.

You may navigate around the menu on the side bar on Astro GO app, or top bar on the Astro GO web version to find shows available.

Menu Guide

• Home: Check out all the recommended content or watch your subscribed TV channels via the   Channel Guide at the bottom of your home screen. 
• Catch Up: Missed an episode of your favourite series? Fret not, Catch Up on the latest episode of your favourite shows on Astro GO. 
• Boxsets: Watch complete seasons and series from our On Demand library anytime anywhere. 
• Movies: Watch recent and popular movies on your devices! You can access a large catalogue of On Demand movies, according to your subscription. 
• Kids: Catch all the cartoons, animations and a variety of shows for kids of all ages. 
• Sports: Watch the biggest sporting shows LIVE on your mobile device, anytime anywhere. 
• Store: Other than your subscribed packages, you can also purchase and watch your favourite Pay-Per-View movies and other Astro exclusive content (not available on iOS devices).

If the bill has been paid, there will not be any additional service tax charge. However, if the bill has been issued by Astro but has not been paid, then the 8% Service Tax will be reflected in the next bill with adjustments on the new tax rate for services rendered from 1st March onwards.

Example:
Bills issued on 15th February will be charged the 6% SST. Customers will see proration for 8% from 1st – 14th March in the next bill issued on 15th March 2024. If you have fully paid your February bill before 1st March, the Service Tax will remains at 6%. You will be able to see the adjustment reflected in your next bill.  
 

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2    

Navigate to Guide.

STEP 3  

Select the channel you would  like to add to favourite list and press "OK".

STEP 4  

Select "Add to Favourites" and press "OK".

STEP 5

You are successfully added the channel to favourite list when this screen appears.

STEP 6

Your selected channel will have a heart tagging after added as favourite.

STEP 1    

On your remote, press the ... button and the Channel Guide page will be displayed on your screen.

STEP 2    

Select the channel you would like to unlock and press "OK".

STEP 3    

Select "Unlock Channel" and press "OK".

STEP 4    

Enter the PIN to unblock the channel.

STEP 5    

You are successfully unlocked the channel when this screen appears.

Please call our Customer Contact Centre or WhatsApp "DH Help" at 03 9543 3838 to cancel your Disney+ Hotstar 3-months add-on pass with Astro. 

The minimum internet speed required to stream via Ultra Plug & Play Box is 30Mbps for 4K UHD viewing, and Ultra/Ulti Plug & Play is 10Mbps for HD viewing. For better streaming experience, we recommend 100Mbps and above.