You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.
2. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem connection

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - LAN  port) to PC/Laptop.

4. If you have change the password in Selfcare Time portal recently, please change the router configuration follows the new password made in  Selfcare, but if you didn't make any changes, please go to Step 5.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 2 / Option 3

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.

2. Gently remove fiber optic cable and  blow / wipe the tip of the fibre cable. This is to clean up the cable in  order to avoid any interferences.

3. Re-insert the fiber cable to the  optical port behind the modem.

4. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem Connection

Router Connection

5.  Make Sure both cables on Modem (LAN Port 4 /LAN Port 3 for second decoder) and Astro Decoder (Network Port) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after  reboot.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.


Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/ power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

Option 5

1. Please ensure LAN cable is directly connected to modem port LAN 1.

2. Please use different LAN port if LAN 1 port is still off / not working.

3. If the issue persists, submit your feedback form for further assistance.

Yes, if a device is faulty due to the customer's negligence, they will be subjected to a penalty fee for each device:

• WiFi router: RM200

• Fibre modem: RM500

• Mesh WiFi: RM200/unit

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

You will be able to view your new package(s) within 24 hours of subscribing. Please note that if you are an Astro customer subscribing to HD channels, you will have to connect an HDMI cable to your TV before you will be able to enjoy the channels.

No, you are not allowed to change your due date or maintain your old due date. Your current due date is as per Astro Policy. Therefore, to ensure that you continue to enjoy uninterrupted services, we advise you to observe this change in due date from Day 30 to Day 25 and proceed with the necessary payment.

Once your Plug & Play Box has been activated, a courier service will reach out to you within TWO (2) weeks for a time for them to pick up the old Astro box and SIM card/Smartcard.

1. Ensure that all cables have been plugged out of the old Astro box. To remove the white satellite cable from your old Astro box, simply hold the cable, twist, and gently pull.
2. Set aside these items to be ready for our delivery partner to pick up from you:

• Old Astro Box
• Old Astro Smartcard/SIM Card (leave this in your Astro Box)

3. When a courier arrives at your residence, do confirm that they are collecting items on behalf of Astro.
4. Allow the courier to check the serial number of the Astro box.
5. Hand them all the items for return, and you're done!

STEP 1  

Press "HOME" button on your remote control.

STEP 2    

Navigate to Preferences and press "OK".

STEP 3  

Navigate to Auto Standby and press "OK".

STEP 4    

Navigate to your preferred selection and press “OK”.

STEP 5  

Select Yes, continue and then press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

1. Ensure power cable is connected tightly.

2. Try to use another power socket / power source to eliminate faulty power sockets/ power sources which  could cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

STEP 1
Switch off the power for your box and  make sure that the adapter's power light is off.

STEP 2
Locate the Smartcard at the front or right side and gently pull it out make sure that the adapter's power light is off.

STEP 3
Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4
Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5
Switch on the power for your box and make sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 6
Turn on your box. You should no longer be experiencing this problem.
If issue persist, please submit the issue in our Feedback Form and attach a picture of your General tab of the STB Diagnostics  for assistance.

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2  

Navigate to Settings.

STEP 3    

Navigate to Parental Control and press "OK".

STEP 4    

Please enter your PIN (Default PIN is 0000).

STEP 5    

Navigate to your preferred category to block and press "OK".

There are various offers currently available for both existing and new customers:

• Existing Astro TV Customers

You may choose from a selection of Astro Fibre speeds from 50Mbps to 800Mbps to accompany your Astro TV Packs from as low as RM60/month for 50Mbps or RM90/month for 100Mbps. That is more than RM900 of savings in total across all speed plans from 50Mbps to 800Mbps. On top of this offer, you will also get to enjoy a complimentary speed upgrade for 24 months if you subscribe within 24 November 2023 to 31 May 2024. This is part of Astro’s initiative to give better value to support loyal customers, and the full details of this offer are as follows:

*Offers applicable to non-Primary Pack bundles only.
**Speed upgrade offer is only eligible for customers who sign up within 24 November 2023 to 31 January 2024.
 

• For New Astro Customers

*Promotion price is applicable for Astro Fibre bundles only.
**Speed upgrade offer is only eligible for customers who sign up within 24 November 2023 to 31 May 2024.
 
 

The Malaysia Communication and Multimedia Commission (MCMC)has issued a directive to all telecommunication companies (telcos) to block the sending and receiving of SMS with URL links. The move is aimed at preventing users from becoming victims of online scams. This exercise is applicable for all person-to-person SMS with URL links sent to or received from local and international mobile numbers, which has already taken effect as of 2 May 2023.

In the new bill layout, there are three tax indicators for customer to refer: S1 (8%), S2 (6%), and N (non-taxable item). Each item list will be marked in accordance with the tax indicator below:


 

STEP 1
Check the Audio settings on your box and set to Auto.
Refer guide to change Set HDMI Audio.

STEP 2
If issue persist, check if there is any 3rd party device (sound system/hdmi splitter) connected between box and TV.

STEP 3
If using 3rd party devices, bypass/remove 3rd party device and make sure HDMI cable connected directly from box to TV.

STEP 4
If issue persist, connect to Live Agent via WhatsApp for help.

Yes, existing Astro customers can subscribe to all Astro Fibre offerings. You also have the option to subscribe to Astro Fibre as a standalone, which comes without any TV packages.

The 24-month contract will be renewed upon signing up for the new packs.

This Service Tax is imposed on customers of Pay TV broadcasting services by the Government. As such the Service Tax will be passed on to the customers.
 

This initiative is part of Astro’s “GO GREEN” journey, which was implemented to promote paperless billing and to play our part in protecting the environment. The objective of the Paper Bill Charge is to encourage our customers to opt for e-Billing as their preferred Bill Delivery Method, which is also a more convenient and efficient way to access and manage their bills. Hence, a fixed RM10.00 monthly charge will be applied to all existing and new Astro customers who opt for Paper Bills as their preferred bill delivery method.

Astro subscribers will have the freedom to subscribe to Netflix via Astro, or they may also choose to continue subscribing via Netflix directly on their own.

Currently the Multiroom (Smart TV) app is supported on four (4) brands with the software version listed below:

1. Sharp
2. Sony
3. LG
4. Samsung

Want to return or recycle your satellite TV devices? It's simple and free!

Here's what you can do with your unused satellite TV devices:

If you have an Ultra or Ulti Box, you may:

1. Return your device to us via Arranged Pick-up:

Step 1: Please call Astro's Contact Centre at 03-9543 3838 to schedule an arranged pick-up by one of our Astro agents.

Step 2: Just sit back and relax! Our courier partner, Citylink will come to your doorstep, dismantle the satellite dish for you and retrieve the devices.

 2. Return your device to us via Dropoff:

Step 1: Please gather your device(s) and click here to find a Customer Service Centre (CSC) or Astro Authorised Retailer (AAR) near you.

Step 2: Don't worry, it's free! Simply walk in during opening hours and hand over the device(s) to one of our Astro agents.

Note: An installer's visit is required to dismantle your satellite dish. However, if you have a Box or other satellite TV devices at home that do not require dismantling, you may walk into any of our authorised dealers and hand them over to the agent.

If your Satellite TV device is NOT an Ultra or Ulti Box, you may:

1)   Recycle your device:

For all Ultra or Ulti Boxes, please return them to Astro via drop-off at a CSC or AAR near you or schedule a pick-up appointment via 03-9543 3838.

For other older Boxes or Satellite TV devices, you are required to discard them only at registered collection centres for proper handling and management of e-waste in an environmentally sound manner. Click here to find a registered collection centre near you.

Note: Upon termination of your Astro service, all Ultra and Ulti Box customers are required to return their devices to Astro. Failure to do so within 14 days of termination may incur a fee of RM100 (not inclusive of Govt. Tax). For customers on all other boxes, please discard your box only at registered collection centres to ensure we all play our part in protecting the environment.

Frequently Asked Questions

Arranged Pick-Ups

1) I missed the pickup appointment; what do I do now?

Our agent will make two attempts to retrieve the device(s) and dismantle your satellite dish within a period of 14 days, failing which the penalty of RM100 (not inclusive of Govt. tax) would be imposed.

2) Can I reschedule my pickup date?

Yes! Please call Astro's Contact Centre at 03-9543 3838 to reschedule your pickup date.

3) My old devices do not require dismantling; do I have to pack them before handing them over to the delivery agent?

Please pack your device(s) in their original box/packaging if possible. If this option is not available to you, just hand the device(s) over to the delivery agent without any packaging. You will not be charged any fees if the original packaging has been damaged/lost.

4) Do I have to print anything or fill in any forms before handing my device(s) over to the Astro agent?

No, you do not have to prepare any documents before handing your device(s) over to the Astro agent. All you have to do is get your device(s)ready before the Astro agent arrives to ensure a smooth handover process.

5) I have an old/unused satellite dish at my home and I am not an Astro customer; can I still schedule an installer visit to dismantle and return it?  

Yes! Not to worry, you can still schedule an installer visit to dismantle the satellite dish from your home.

Drop-offs

1) Do I have to pack my device(s) before handing it over to the Astro agent?

Please pack your device(s) in their original box/packaging if possible. If this option is not available to you, just hand the device(s) over to the Astro agent without any packaging. You will not be charged any fees if the original packaging has been damaged/lost.

2) There are no Customer Service Centre (CSCs) or Astro Authorised Retailers (AARs) near me; what do I do now?

Please opt for courier pick-up if there are no CSCs or AARs near you. Call 03-9543 3838 now to schedule a pick-up appointment by one of our courier partners if you are holding an Ultra or Ulti Box For non-Ultra or Ulti boxes, you may recycle your box at a registered collection center. Click here to find a registered collection center near you.

3) Do I have to print anything or fill in any forms before handing my device(s) over to the Astro agent?

No, you do not have to prepare any documents before handing your device(s) over to the Astro agent. All you have to do is hand the device(s)over to the agent and you're done! You will also receive an acknowledgment slip after successful handover.

4) I found my Box and Smart card, however, the cable(s) that came with it is lost; will there be any penalty fees?

No, please return your old Plug & Play Boxes and Smartcard. There will be no penalty fees if the cable is damaged or lost.

Recycle via Registered Collection Centres

For all recycling-related questions, please click here.

Still Need a Hand?

Not to worry, we are only a phone call or a message away! Call or WhatsApp our Customer Contact Centre at 03-9543 3838 and an Astro agent will be available to assist you immediately.

Please disregard the reminder if payment had been made and do check if you have any outstanding balance on Astro Quick Pay.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to Installation Settings and press "OK".

STEP 4    

Enter your PIN to access this setting. (Default PIN is 0000).

STEP 5    

Navigate to Restore Factory Settings and press "OK".

STEP 6    

Navigate to Yes, continue and  press "OK" to  confirm your selection.    

Otherwise, navigate to No, go back to maintain the settings.

STEP 7    

Please reboot your box.

STEP 8    

New Installation Settings screen will appear.    

Click here to follow New Installation Settings guide.

If Netflix is included as part of your Astro pack, you will find it in My Astro app 

where you will be able to manage all the streaming apps you are entitled to.  

Netflix will also be included in your Astro bill under “Monthly Charges”  

If you have added Netflix to your bill (Netflix Add-on), the Netflix subscription charge will appear in your Astro bill under “One-time charges” as Netflix App Subscription or Netflix Premium and will be charged monthly. You should refer to Netflix account Management for any changes to your Netflix subscription or should you wish to change to other billing methods.

You may proceed with the following troubleshooting steps and it shouldn't take you much longer than 15 min

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Yellow port at Tplink Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to tplinkwifi.net and to access to below login page. Type the Username and  Password, then click "Login".

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your  router previously, the password may be different.

For example, below is the login details of the above router:
 

Username: admin

Password: TIMECE24
 

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, choose Advanced and click the Wireless tab on the left menu. Then, select Wireless Settings from the sub menu. Below screen will appear for 2.4GHz selection.

i. Please ensure to tick Enable Wireless Radio function.

ii. To change the channel, click the  drop-down arrow for Channel, then select your desired channel.

Choose between 1 to 13 (Suggested  channels : 1,6,11). Then, click "Save" for the changes to take place.

iii. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

iv. Next, select 5GHz to make changes on the wireless channel for 5GHz.

v. Click the drop-down arrow for Channel, then select your desired channel from the selection.

vi. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

The different light colours on your Astro Ultra Box or Ulti Box informs you on the phase the box is going through.

‍

1. Ultra Box magenta light / Ulti Box purple light - Your box is turned "On". ‍

Press the Home button to launch Video On Demand and stream anytime or press channel number on your remote.

‍

2. Ultra Box / Ulti Box orange light - Your box is on "Standby" mode.

Your box is ready to be turned "On" or leave it in this mode to receive new software updates.

3. Ultra Box / Ulti Box blinking orange light - Your box is booting up.

Please wait a few minutes for the box to start.

‍

4. Ultra Box / Ulti box blinking blue light - Your box is downloading a software update.

Please wait a few minutes for the download to complete.

The main features and changes in this update are the revamped look and feel of Astro's user interface on the Astro Ultra/Ulti Boxes and Astro GO, which include redesigns to the Astro interface that consists of title rows at the Home Page to feature popular franchises, new live programmes posters and changes to the menu bar for easier navigation; auto-start Interactive Mode on Astro GO; as well as a Picture-in-Picture mode that shrinks your video player so you can keep watching your favourite shows while using other apps.

The details of each feature are:

• New Astro user interface
• Picture-in-picture mode
• Auto-start Interactive Mode on Astro GO

For more info, please read our dedicated FAQ on this here.

For My Astro App Users 
Go to the "Account' tab and scroll to "Personal Info' section. Click "Name & contact info' to view and update your personal contact information.

For Ultra and/or Ulti Users 

1. Launch the My Astro app on your Home screen and you will land on your My Astro account dashboard. Then, press the yellow button on your Astro remote control to visit your "Account details".
2. Press the down button to view the "Personal info".
3. Press the left button and focus on the edit icon for the contact details, press on "OK" to change your contact details.

For customers with Entertainment Plus, Movies Plus, Sports Plus, Premium 2, Premium 3, and Platinum Pack 

1. Launch Netflix from the home screen or via remote control. 

2. Click on Get Started

3. If you are an existing Netflix customer, please fill in the email address and password associated with your Netflix account. Once successfully completed, all existing settings and watching history on your Netflix account will be brought over. If you are a new Netflix customer, create a new account by filling in your email address and a password for your new Netflix account. 

4. In the next screen, you will be shown your default Netflix package “Standard”, you can choose to upgrade to “Premium” here. 

5. The final screen provides a summary of your account including your email. Click Start Watching to enjoy Netflix on your Ultra/Ulti Box. 

‍

For Non-Entertainment Plus, Premium 2, Premium 3, and Platinum Pack Pack customers (New Netflix customers) 

1. Launch Netflix from the home screen or via remote control.

2. Click on Join Now

3. Create a new account by filling in your email address and a password for your new Netflix account. 

4. The final screen provides a summary of your account including your email. Click Start Watching to enjoy Netflix on your Ultra/Ulti Box. 

Note: The Netflix plan will be defaulted to Premium, you may select ‘Change Plan’ to choose the ‘Standard’ plan. 

‍

For Non-Entertainment Plus Pack, Premium 2, Premium 3, and Platinum Pack customers (Existing Netflix customers) 

1. Launch Netflix from the home screen or via remote control 

2. Click on Sign-in 

3. If you are an existing Netflix customer, please fill in the email address and password associated with your Netflix account. 

4. You will be able to start watching Netflix on your Ultra/Ulti Box once you log in.

It will take around 10 to 15 minutes before you are able to view your purchase.

Yes, existing Astro & Broadband customers within contract or out of contract can subscribe to Astro Fibre Bundle. The 24-month contract will be renewed.

However, your contract with Maxis/Allo needs to be terminated before signing up to this offer. An early cancellation fee applies if you are still within contract.

‍*Subject to Terms &Conditions of your contract

‍

1. Please connect your computer or laptop to your Astro Fibre router using WiFi or LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

2. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, type http://192.168.100.254 and below page will appear.

‍

Login using your username and password  if you have changed the router login setting. Otherwise, your default router  login is as per below.          

Username: user
Password: user

‍

4. Once you have successfully logged in, the router's web-based setup page will appear.

‍

5. At the top of the page, click WLAN to configure the WiFi parameters.

‍

6. You may change the Primary SSID (WiFI Name) and the WPA Passphrase (WiFi Password) to follow your preferences for 2.4G Wi-Fi Settings, then click "Save & Apply" for the changes to take place.

‍

7. You may make the same changes for 5G Settings by change the Primary SSID (WiFI Name) and the WPA Passphrase (WiFi Password) to follow your preferences, then click "Save & Apply" for the changes to take place.

The New Astro First serves as the one-stop, ultimate home cinema offering the biggest and latest local and international blockbuster films where you can:-

• Enjoy value for money viewing for local and international movies from only RM15* per movie or RM17* for UHD movies (*excluding tax).
• Stream each rented movie for as many times as you like within 48 hours* (*unless stated otherwise) anytime, anywhere via On Demand on your Astro Box or Astro GO.
• Watch local/regional movies or international movies from Hollywood studios as recent as 2 weeks or 3 months respectively from Malaysia's cinematic release, in addition to exclusive titles only available on Astro First.

You can access the self-help service 24 hours a day for the following: 

1. Check account balance.

2. Refresh your Smartcard if your account is active but TV screen displays "This channel is not included in your subscription" or "We apologise for the service interruption".

3. Check application status.

4. Guide on Self Service troubleshooting guide via SMS Link.

5.  Check trouble ticket appointment announcement.

6.  Apps Related Self Service login & Activation guide via SMS Link.

7.  Apps Related FAQ Details via SMS Link.

You will be notified 30 days before the expiry on the renewal of subscription and can opt out from auto renewal at least (2) days before the auto-renewal date. 

If you want to opt out of your auto-renewal for Disney+ Hotstar, please contact our Customer Contact Centre at 03 9543 3838 and speak to one of our customer service executives to change your package according to what suits you best at least two (2) days before the next auto-renewal date. Alternatively, please WhatsApp us at 03 9543 3838 and type "DH Help

The Multiroom (Smart TV) will mirror the subscription entitlement as per your primary subscription. However, NHK World, Radio, Sky News channels and 3rd party apps such as Netflix, Disney+ Hotstar are not available via the Multiroom (Smart TV).

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which could  cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

If you are subscribed to Netflix via a bundle, Netflix comes by default as part of your entitlement.

If you are subscribed to Netflix as an a-la carte, the cancellation of Netflix can only be done via Netflix's Website, etc). This change will reflect in your next bill. From mid-December 2021 you may also cancel Netflix add-on through Astro Call Center.

You may reach out to Astro's customer service at 03-95433838 if you think there's an error regarding your redemption or rewards.

You can add a new Netflix account to your bill through CH 741 or clicking the Netflix button on the remote control. Please enter the email address you would like to use for Netflix subscription and ensure the Billing partner is Astro.  

If you would like to transfer your existing Netflix Account to be charged under Astro bill, please follow the steps below:  

1. Cancel your existing subscription with Netflix  

1. Once the remaining duration of your existing subscription has ended, you may proceed to subscribe for Netflix via Astro bill  

1. To subscribe, go to CH 741 and enter the email address used for your previous subscription with Netflix  

1. Once successfully completed, all existing settings and watching history on your Netflix account will be brought over  

1. Clearly indicate full name of Astro customer, contact number and Astro subscription account number when making each payment (e.g. on bank-in slips)
2. For Direct Debit, please contact your bank for standing instructions. Provide the full name of Astro customer and Astro account number. The Direct Debit service may not be available with all banks. Please check with your bank for confirmation of Direct Debit service.
3. Please inform us of any changes in billing address/information by contacting us via one of these platforms.

IMPORTANT NOTICE: To avoid any problems in payment processing, please pay only at authorised Astro payment channels

No, you will not be able to manage your account with the Astro Fibre App. However, you may download the “MyAstro” app on your mobile device now to manage your Astro account in a fast and easy way.

Most Astro customers are eligible to use the app, web, Ultra and Ulti boxes. You will only need to login with your Astro ID. Do note that your Astro ID must be linked to your Astro account to use the service. Click "Create now!' on the login page and you will be guided to create an Astro ID if you do not have one.