This issue occurs because  your TV does not support the higher resolution.
 

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.
 

STEP 2

Switch on the power for your box and make sure that the adapter's power light is on.
 

STEP 3

Press the standby button repeatedly after switch on the power.

The Startup Options screen will appear on your TV.

STEP 4

Press "987" to access the Advanced Startup Options menu.

Then, press "1" to initiate a reset setting.

STEP 5

Press "OK" to confirm restore to factory setting.

STEP 6

After the factory setting is restored, TV will turn blank.

Please wait until the box completes initiate setup.

STEP 7

Press "1" to initiate Linux download on the software.

STEP 8

Once completed, the following screen will appear on your TV.

Refer to Installation Setup guide here to complete the setup.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

Your documents will be handled in compliance with standards set by PDPA (Personal Data Protection Act 2010) and will not be used for other means without your specific consent.

You may retain your watch history and settings of your existing Netflix account by using the same email of your Netflix account during the linking of your Netflix account with Astro.

Yes, you have the option to transfer the credit balance to another active Astro account. It will be considered as payment to that account and is subject to Astro's terms & conditions.

You would have to create a new Astro ID with your email address or mobile number and link your Astro subscription. Please follow the steps in the link here

No, the Astro Fibre App is a free mobile application for all Astro Fibre customers with the latest RG21 router.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Preferences and press "OK".

STEP 3  

Navigate to Language and press "OK".

STEP 4    

Choose your language preferences and press "OK".

STEP 5  

Select Yes, continue and press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

The Kids Friendly Profile is an enhancement to the Kids User Profile feature with the following major improvements:

Kid-Friendly Channels, On Demand content & TV Guide: Only Kid-friendly channels and On-Demand content can be viewed in the Kids Profile. Other channels and content are not viewable. The same applies to the Kids TV Guide.
1. PIN control for the Kids Profile:  When switching from a Kids Profile to an adult profile (i.e.: Father or Mother), a PIN entry will be required.
2. Limited Kids Profile Content Search: Only Kids age-appropriate content can be searched and displayed within the Kids Profile.
3. Kids Profile Based Recordings: Kids Profiles will have their own personalised age-appropriate recordings without any overlap with other user profiles. This feature will be available from 17th August onwards.

These enhancements are available across the Astro GO app, Ultra/Ulti Box, and Multiroom Box/Smart TV app.

Click here to find out more on this new feature and how to use it!

All streaming apps willbe made available on the Ultra Box first, followed by the Ulti Box. If youwould like to upgrade to the Ultra Box, please visit product.astro.com.my/tv or reach us via WhatsApp by typing “Hi” at 03-9543 3838 forassistance.

STEP 1    

Switch OFF the power of your Ultra / Ulti box and make sure that the adapter's power light is off.

STEP 2    

Switch ON the power of your Ultra / Ulti box and make sure that the adapter's power light is on.

‍

STEP 3  

Put the box on standby mode.

STEP 4

Press and hold the Home button on the box.

STEP 5    

Wait until "boot" appear on the front panel and released.

STEP 6

When “boot” appears, press “Standby”,  “Left “, “Up” continuously until Auto Update appear on box screen and Software Update progress on TV.

‍

‍

STEP 1    

Switch OFF the power of your box and make sure that the adapter's power light is off.

‍

STEP 2

Switch ON the power of your box and make sure that the adapter's power light is on.

STEP 3

Press Standby, Ch+, Standby keys on the box simultaneously when the "boot" message appears on the box front  panel.

The Software Update progress screen will appears.    

The update will take 10 - 15 minutes to complete. Please be patience.

STEP 1  

Switch OFF the power of your box and make sure that the adapter's power light is off.

STEP 2    

Switch ON the power of your box and make sure that the adapter's power light is on.

STEP 3

Press the standby button repeatedly after switch on the power.

STEP 4

Press "OK".

STEP 5    

The Software Update progress screen will appears.

The update will take 10 - 15 minutes to complete.

Please be patience.

Yes, customers will be charged a fixed Paper Bill Fee of RM10.00 per bill every month for each account.

STEP 1  

On your remote, press the HOME button.

STEP 2

Navigate to SETTINGS icon and press "OK".

‍

STEP 3  

Navigate to Manage Satellite Frequency and press “OK”.

STEP 4

Choose Test Satellite Frequency and press “OK”.

STEP 5  

Choose "Confirm" to continue Test Satellite Frequency and press “OK”.

‍

STEP 6  

Satellite Frequency Test progress screen will be displayed.

‍

STEP 7  

The test result will be displayed once completed.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2A

Unplug the HDMI cable from your box and plug it back in securely. Do select the correct TV input.

STEP 2B

If you are connecting using RCA cable, please unplug the RCA cable from your box and plug it back in securely.

STEP 3

Switch on the power for your box and make  sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 4

Turn on your box. You should no longer be experiencing this problem. If issue remain, replace to another HDMI  cable.        

If no improvement seen, please submit the issue in our Feedback Form and attach a picture of your smart card number for assistance.

Astro wants to give our members the convenience of having all their favourite series, exciting originals, vernacular signatures, live sports and local blockbuster movies in one place. Astro customers will be able to enjoy greater convenience by having Netflix bundled with their Astro subscription, consolidating the subscriptions, and providing easy access for payment in a single bill, at the best value.

Unfortunately, your Disney+ Hotstar access with Astro will be terminated as well. 

Real-time payments are posted almost instantaneously. However, daily system maintenance occurs between 12AM to 3AM - any payment made during this period will be delayed until system maintenance is complete.

STEP 1
Please wait while your Astro box initializes.



STEP 2
Select your preferred language.



STEP 3
Navigate to Next and press "OK".



STEP 4
Select Auto as the Video Resolution.



STEP 5
Navigate to Next and press "OK".



STEP 6
Navigate to Confirm and press "OK" to confirm your selection if you are able to read the texts on screen properly.
Otherwise, navigate to Cancel to revert to the previous settings.



STEP 7
Select IPTV Plug & Play (self-install) as the box operating mode.



STEP 8
Navigate to Next and press "OK".



STEP 9
Select your preferred connection.
For connection via Wi-Fi, proceed to STEP 10.
For connection via LAN Cable, proceed to STEP 16 once you are connected.



STEP 10
Please wait while your Astro box searches for available Wi-Fi networks.



STEP 11
Navigate to your preferred Wi-Fi network and press "OK".



STEP 12
Please enter the password to connect to the Wi-Fi network.



STEP 13
Navigate to Done to continue.



STEP 14
Please wait while your Astro box connects to the internet.



STEP 15
Navigate to Yes to allow your Astro box to connect to this network automatically.
Otherwise, navigate to No.
Proceed to STEP 17 for the next step.



STEP 16
Navigate to Next and press "OK". 



STEP 17
Your box's connection status will be displayed.
Navigate to Finish to complete the setup.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.

1. Try  loading the site on a different device.

  Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.

  If the website doesn't load on another device, the problem is either with the network or the website itself.

2. Restart your computer.

  Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.

3. Try loading the site in a different browser.

  There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.

4. Temporarily disable your antivirus program.

  Your antivirus software may be interfering with your ability to load certain websites.

  Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.

5. Reset  your modem and router.

  Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.

6. Check  your computer's date and time settings.

  If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.

  Check your computer or mobile device's clock to make sure that it is set to the correct time and date.

In the  event the problem persists, please provide below details for further  escalation:

  i. List of websites effected.          

  ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.  

  iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.          

  iv. Run the Ping Test -  Please click here for Ping Test guideline.

 Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

You may report the incident on WhatsApp at 03-95433838 by typing PNP and our dedicated agents will attend to your matter. Please have your Airway Bill tracking numbers ready for validation.

If a replacement box/Astro SIM card is deemed necessary, a new Plug &Play Box and a new Astro SIM card will be couriered to your service address.

You are entitled for free mesh WiFi devices when you sign up for Astro & Broadband with Maxis fibre 500Mbps or 800Mbps speed only.

Mesh WiFi is not available with Astro & Broadband with Allo. However, you may purchase the Mesh WiFi devices separately to pair along with you Allo broadband.

Currently, there are no rebates provided when you sign-up for the Ultra/Ulti Plug & Play Box.

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

2.Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user

Password: user

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi to configure the WiFi parameters.

6. You may change the Wi-Fi Name and the Wi-Fi Password as per your preferences, then click "Apply".

7. Your Wi-Fi Name and password has been changed. Kindly ensure to reconnect your WiFi according your new WiFi name and password.

No there will not be any penalty.

For the Multiroom subscription on a box setup, if your subscription is within the 24-month contractual period. Then a pro-rated penalty of RM600 will be applied for any Astro box except for Ultra Box, which the penalty will be RM1,000.

No, you are still able to subscribe to iQIYI on your current Astro pack.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer  than 15 minutes.

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Black port at D-Link Router and direct to the computer/laptop).    

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.    

3. On the address bar, please go to tplinkwifi.net and to access to below login page. Type the Username and Password, then click "Login".

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your router previously, the password may be  different)

For example, below is the login details of the above router:

Username: admin

Password: TIMECE24

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, choose Basic and then click Wireless tab on the left menu to access to below screen.

6. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

7. You may change the Wireless Network Name (SSID) and the Password to follow your preferences, then click "Save"  for the changes to take  place.

Please reconnect to the new wireless name with the new password once completed.

‍

Yes, as part of our Astro Fibre Movies & Sports Campaign, new Astro Fibre customers can enjoy 50Mbps + the Movies/Movies+/Sports/Sports+ Pack TV bundle for a special price from only RM164.99/month when they sign up within the campaign period, with more than RM800 savings in total.

The payment will take some time to reflect in My Astro app and web account. If you experience any further issues or it is still not reflecting in My Astro, please reach out to us via WhatsApp at 03-9543 3838 for more details.

No, the PVR service fee is included in all Starter Pack, Value Pack, Super Pack Lite, Super Pack and Super Pack Plus subscriptions only.