Astro GO is a companion app that is complimentary for all Astro subscribers and allows up to 2 users to stream at the same time. 200 hours of cloud recording* come complimentary with your Pay TV subscription. 

Astro GO+ is an add-on service that enables up to 4 users to stream Astro GO and/or Multiroom Smart TV** at the same time. The amount of cloud recording storage will also be increased to 1500 hours. 

 *Cloud recording hours are shared across your Astro Box, Astro GO and Multiroom Smart TV 

** Provided that you have a Multiroom Smart TV subscription

Liga Malaysia is available for all customers with a HD enabled box including Zapper, DMT5, Ulti Box and Ultra Box.

Having trouble with  your phone line ?

You may proceed to contact dedicated service provider directly - 1 800 8211 23

STEP 1

Identify your remote control:

a)   Remote control with Astro logo at the bottom of the remote, proceed to STEP 2.

b)   Remote control with Astro logo at the top of the remote, proceed to STEP 4

‍

STEP 2 (Astro Logo at the bottom of the Remote)

On your remote, press the “set tv” button and set tv instructions will be displayed on top of your screen:

‍

STEP 3

Follow the steps appear on the TV screen to sync your Astro remote and complete the setup.

‍

STEP 4 (Astro Logo atthe top of the Remote)

Press and hold “tv input” key on bottom left of the remote for 3 seconds until the LED blinks twice.

STEP 5

Enter the 2-digit TV Code of your TV Brand and the LED will blink twice:

‍

STEP 6

Try out the TV controls (TV Standby or adjust Volume) to check if they are working correctly.

‍

STEP 7

Press ok and wait for the LED to blink twice to save the settings.

Yes, all existing Astro & Broadband customers within contract or out of contract can subscribe to Astro & Broadband offerings. The 24 months contract will be renewed upon signing up for the new packs.

STEP 1

Try to change channels on your Astro remote. Check the LED light.
If the LED is blinking 3 times or if it is not blinking, replace the batteries and proceed to STEP 2.
Otherwise, if the LED is blinking 1 time, your remote is working fine, let's proceed to STEP 3.

STEP 2

Check if you can change channels using your Astro remote control. You should no longer be experiencing this problem if is a battery issue.
If issue remain after batteries replacement, proceed to STEP 3.

STEP 3

You need to refresh the box setting manually from the box front panel.
Refer to Refresh Box setting (Clear NVRAM) - Ultra / Ulti Box. 
If issue persist, please submit the issue on our Feedback Form.
 

STEP 1
On your remote, press the HOME button and the menu will be displayed on top of your screen.
STEP 2
Navigate to Settings.


STEP 3
Navigate to Network Settings and press “OK”.


STEP 4
Navigate to Test Connection and press “OK”.


STEP 5
Test Connection results will be displayed on the screen.

Tune to channel 200 - select on "My Account".Your Total amount due will be stated under the "Bill Summary" section.

**Please note that this feature requires your box to be connected to your home Wi-Fi. Alternatively you can perform the SMS steps displayed on the screen to check your bill amount.

Your account number will be used to identify/verify you for all After Sales-Services. You may also use your mobile number/ Astro smart card number/ NRIC number or Astro Box number.

No, your rewards cannot be transferred to another person or exchanged for cash.

Not all shows/channels will be available on the Plug & Play Box as this depends on contractual rights with specific guidelines on the entitlement of these shows/channels and what you have as a part of your subscription.

• Customers subscribing to Plug & Play Box with or without Astro Broadband will not have access to 1 (one) Channel - NHK World

Please be assured that we are continuously working hard to make more content available on the Plug & Play Box.

If you prefer to have all these channels, we recommend that you choose the Satellite dish option for the Ultra or Ulti Box.

Unavailable channels are as below:

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.    

2. Ensure the fiber cable from your wall socket and modem is securely connected.

Notes: You might be connected to LAN 1 if backbone is Maxis

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 2/ Option 3/ Option 5/ Option 6

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.

2. Ensure the fiber cable from your wall socket and modem is securely connected.

3. Ensure both cables on the Modem (LAN Port 2) and Router (WAN Port - Red port) are properly connected.

Notes: You might be connected to LAN 1  if backbone is Maxis

Router connection

4. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

5. Please make sure both cables on Router (Any Yellow port) and Astro Decoder (Network Port behind decoder) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

7. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

No, the Service Tax is a tax payable entirely to the Government. Astro acts as a collection agent for the Government.
 

STEP 1
Check the internet connectivity by run the Test Connection.
Refer Run Test Connection.


STEP 2
Verify the average speedtest based on the Test Connection result.
a. Above 10Mbps - Proceed to STEP 5
b. Less then 10 Mbps - Proceed to STEP 3

Notes: Minimum 10 Mbps internet speed from box requires in order to get a stable connection.



STEP 3
Check the connection to the box either using Ethernet (LAN cable) or Wi-Fi.
a. If using Ethernet (LAN cable) - Connect to Live Agent for help.
b. If using Wi-Fi - Proceed to STEP 4



STEP 4
Check location of the decoder and router.
a. If nearby (within 1.5m) - Try connect to box from router using LAN cable.
b. If far (more than 1.5m) / No LAN cable - Proceed STEP 5



STEP 5
Reboot router, modem and decoder.
If issue persist, please try again after 30mins to 1 hour. Connect to live agent if persist after 30 mins to 1 hour.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.

1. Try  loading the site on a different device.

  Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.

  If the website doesn't load on another device, the problem is either with the network or the website itself.

2. Restart your computer.

  Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.

3. Try loading the site in a different browser.

  There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.

4. Temporarily disable your antivirus program.

  Your antivirus software may be interfering with your ability to load certain websites.

  Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.

5. Reset  your modem and router.

  Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.

6. Check  your computer's date and time settings.

  If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.

  Check your computer or mobile device's clock to make sure that it is set to the correct time and date.

In the  event the problem persists, please provide below details for further  escalation:

  i. List of websites effected.          

  ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.  

  iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.          

  iv. Run the Ping Test -  Please click here for Ping Test guideline.

 Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our  server.

1. Power reset (on & off) your TV, Astro Decoder, Modem and Router.

2. Ensure standard physical connection (No 3rd party devices connected to decoder and modem).

3. Please ensure at all-time your router is 0.5 meter away from your Astro Decoder to avoid signal interferences.

4. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [connect the LAN (cable) at any LAN port at router and direct to computer/laptop].

5. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

6. On the address bar, please go to http://www.speedtest.net/ and below page will appear.

7. Click "Change Server" to edit the settings preferred by Internet Service Provider (ISP).

8. Edit the server settings by search and select the required server required by ISP.

    For Maxis provider - Select Subang Jaya - Maxis server.

    For TIME provider -  Select Shah Alam - TIME dotcom Bhd server.      

    For Allo provider -  Select Cyberjaya - Global Forway Sdn Bhd server.

9.Click "GO", and the test will  begin.

The test is completed once both download and upload speeds are displayed.

Sample of the Speedtest result is shown below.

**Please  ensure the snapshot includes a time stamp and network used either LAN cable  or wireless (as per picture above)

10. Kindly screenshot or take a picture of the result, name it as "LAN Speedtest".

11. Repeat the test once again using Wi-Fi connection (Please unplug your LAN cable and connect via wireless connection using your SSID).

12. Screenshot or take a picture of the  result, name it as "WiFi Speedtest".

No additional subscription is required. Video On-Demand (VOD) is a value-added service for all Astrro customers with connected Astro boxes (Ultra Box, Ulti Box, HD-PVR & PVR boxes). All you have to do is connect your decoder to your home Wi-Fi and you'll be able to access the world of on demand. Binge-watch, rewind, fast-froward and stream all your favourite shows anytime.

If you have more than one card registered for OTP payments, you will be asked to select the specific card to be used for that specific transaction.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be experiencing this problem.    

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

STEP 1  

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3    

Navigate to Display and press "OK".

STEP 4    

Navigate to TV Settings and press "OK".

STEP 5    

Navigate to Conversion for 4:3 Input Video, select your preferred selection and press “OK”.

STEP 6    

Select Yes, continue and press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

Of course not! It is a value-added service introduced for your convenience.

Visit https://product.astro.com.my/box or check out our user guide for a quick and easy way to get started!

Yes, existing Astro customers can subscribe to all Astro & Broadband offerings. 24 months contract will be renewed upon signing up for broadband.

Please note that your request to opt out has been processed, and payment for Disney+ Hotstar is not required. Your bill adjustment will be reflected in your next bill. 

STEP 1
Please wait while your Astro box initializes.



STEP 2
Select your preferred language.



STEP 3
Navigate to Next and press "OK".



STEP 4
Select Auto as the Video Resolution.



STEP 5
Navigate to Next and press "OK".



STEP 6
Navigate to Confirm and press "OK" to confirm your selection if you are able to read the texts on screen properly.
Otherwise, navigate to Cancel to revert to the previous settings.



STEP 7
Select Satellite as the box operating mode.



STEP 8
Navigate to Next and press "OK".



STEP 9
Select your preferred connection.
For connection via Wi-Fi, proceed to STEP 10.
For connection via LAN Cable, proceed to STEP 16 once you are connected.



STEP 10
Please wait while your Astro box searches for available Wi-Fi networks.



STEP 11
Navigate to your preferred Wi-Fi network and press "OK".



STEP 12
Please enter the password to connect to the Wi-Fi network.



STEP 13
Navigate to Done to continue.



STEP 14
Please wait while your Astro box connects to the internet.



STEP 15
Navigate to Yes to allow your Astro box to connect to this network automatically.
Otherwise, navigate to No.
Proceed to STEP 17 for the next step.



STEP 16
Navigate to Next and press "OK". 



STEP 17
Navigate to Universal.



STEP 18
Navigate to Next and press "OK".



STEP 19
Select 01 M3B VL - 10732 as the Entry Point.



STEP 20
Navigate to Next and press "OK".



STEP 21
Please wait until the signal reading is updated.
Navigate to Finish and press "OK" to complete the settings.

No, the PVR service fee is included in all Starter Pack, Value Pack, Super Pack Lite, Super Pack and Super Pack Plus subscriptions only.

If you have forgotten your username or password, you may follow the steps below:

Step 1. Go to netflix.com

Step 2: Click on Sign In

Step 3: Click on "Need Help

Kindly note that affected customers will be adequately informed 30 days prior to the implementation via SMS which are sent out in phases (Starting 1 July), with scheduled announcements across WhatsApp, My Astro app, and Astro website.

Yes, please WhatsApp "DH Help

1. Please standby  computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.254 and below page  will appear.

If below box appear, please enter required details:

USERNAME: Administrator

PASSWORD: (ACCESS KEY AT THE RGW STICKER)

(These are the defaults, if you have done previous configuration on your router the password may be different)

4. Once enter into the page "'TECHNICOLOR TG784N V3'', you may follow below steps to get the best wireless channel information.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. In order to get the best wireless channel, click "Wireless Scan" to scan available surroundings wireless Channel.

D. Please choose channel with lesser number of usage.

Example in below case, you may choose channel 4.

5. To configure wireless channel, please proceed with below steps.

A. Select "Home Network".

B. Click "WLAN: SSID" to proceed to next screen.

C. Then, click "Configure" to change the channel selection (automatic to manual) and other configuration option.

D. Please ensure below items:

i. WLAN Enable: Tick

ii. Interface Enable: Tick

iii. Change the Channel Selection to Manual

iv. Change the wireless Channel based on Step 4(D).

v. Once completed the selection, click the "Apply" button.

1. Ensure power cable is connected tightly.

2. Try to use another power socket / power source to eliminate faulty power sockets/ power sources which  could cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.