Unfortunately, you cannot link your direct Disney+ Hotstar subscription to your Astro account. Please ensure that the mobile number used for your direct subscription to Disney+ Hotstar is different from the mobile number used to activate Disney+ Hotstar entitlement via your Astro subscription. If you do not have an alternative mobile number to nominate, kindly contact Disney+ Hotstar's customer service directly at disneyplus.my@hotstar.com for details on how to cancel your direct subscription. 

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

No, you will not be automatically switched to the new pricing. To perform a manual switch, please contact us at 03-9543 3838.

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

STEP 1  

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3  

Navigate to Display and press "OK".

STEP 4    

Navigate to Resolution and press "OK".

STEP 5    

Navigate to your preferred selection and press “OK”.

STEP 6    

Select Yes, continue and press "OK" to confirm on the changes.    

Otherwise, select No, go back to cancel.

Unfortunately, only Astro Fibre customers who subscribe from 24 November 2023 to 31 May 2024 are eligible for this free speed upgrade. However, you may still get the speed boost by calling in to our Customer Contact Centre at 03-9543 3838 and re-contracting with us. Kindly note that your account will restart with a new 24-month contract.
 

Yes, there are five digital bill platforms available for all customers to check their Astro bills: 

A.    MyAstro Web

1.    Visit www.astro.com.my

2.    Goto “My Account”, then select “Manage Account”

3.    Login to My Astro Web using your Astro ID

4.    Select “Account” to view your bills 

B.     My Astro app

If you do not have it installed, you may download it here (Google Play Store) or here (IOS App Store)

‍

C.    WhatsApp 

Just WhatsApp “Hi” to 03-9543 3838 and then follow the instructions to view your bill, account status, pay and download bill. 

Note: You are required to provide your MyKad/PassportNo. to view your bill, account status and pay your bills. To download your bills, you will be required to provide your Account/Smartcard No.

D.     Astro Quick Pay 

1.    Visit https://pay.astro.com.my

2.    Enter your 10-digit Astro Account Number and follow the instructions to view your bill, account status, pay bills or add a billing reminder on your Google calendar. 

E.    IVR

1.    Call +603-95433838

2.    Press 1 for Account Related Queries

3.    Input your 10-digit Astro Account no. or 12-digit MyKad no.

4.    Press 2 for Payment and Billing

5.    Press 1 to receive an SMS with your bill balance and a link to pay online

F.    Channel 200

Ensure your Ultra or Ulti Box is connected to the internet. Tune in to CH200 and follow the instructions displayed on your TV screen to view your bill amount.

G.     Auto-Debit

Alternatively, please register for Auto-Debit by following the steps here for hassle-free payments.

You have the liberty to manage device connection on your own.

Please check your internet speed and connection status via internet connection test. If your internet is working fine and the issue persists, proceed to submit report via WhatsApp or Feedback Form.

If you would like more information or to provide feedback on Astro Rewards, kindly reach out to us at 03 9543 3838 or visit one of our Astro service centres.

1. Please use a LAN ethernet cable and connect your computer/laptop to the back of the Maxis Router.

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox, etc.

3. On the address bar, please go to http://192.168.1.254 and the page below will appear.

    The default login of the router as below. If you have done a configuration on your router and changed your password previously, please use the password you have previously set.

    Username: administrator

    Password: Router S/N (Available on the sticker at the back of the router)

4. Once you have successfully login, the router's web-based setup page will appear.

5. From the left menu, select WIRELESS to access the screen below.

6. You may change the Network Name (SSID) and the Password to follow your preferences, then scroll to bottom and click "Apply"  for the changes to take  place.

7. A warning box will popup, click "OK" for the changes to take place and reconnect to the new wireless name with the new password once completed.

8. Please wait until the connection reestablish.

The PVR comes with a 12 months warranty from the date of activation.

Please follow the steps below to retrieve your Astro ID:



Note: Only Astro customers whose Astro ID is linked to their subscription can retrieve their Astro ID this way. Otherwise, you would need to create a new account.
 

STEP 1
Switch off the power for your box and  make sure that the adapter's power light is off.

STEP 2
Locate the Smartcard at the front or right side and gently pull it out make sure that the adapter's power light is off.

STEP 3
Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4
Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5
Switch on the power for your box and make sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 6
Turn on your box. You should no longer be experiencing this problem.
If issue persist, please submit the issue in our Feedback Form and attach a picture of your General tab of the STB Diagnostics  for assistance.

Yes, any active Astro subscriber with a minimum primary subscription fee of RM100 can subscribe to a Multiroom (Astro Box) at a price of RM49.99 monthly with the box setup (subscription price is subject to Govt Tax).

Refund process required 5 working days by Astro and additional 3 - 7 working days required subject to the respective processing banks.

Unfortunately, your Disney+ Hotstar access with Astro will be terminated as well. 

STEP 1  

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2    

Navigate to SETTINGS and press “OK”.

STEP 3  

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4    

Refer to the signal strength % shown on the top left of your screen.

STEP 1
Check the internet connectivity by run the Test Connection.
Refer Run Test Connection.


STEP 2
Verify the average speedtest based on the Test Connection result.
a. Above 10Mbps - Proceed to STEP 5
b. Less then 10 Mbps - Proceed to STEP 3

Notes: Minimum 10 Mbps internet speed from box requires in order to get a stable connection.



STEP 3
Check the connection to the box either using Ethernet (LAN cable) or Wi-Fi.
a. If using Ethernet (LAN cable) - Connect to Live Agent for help.
b. If using Wi-Fi - Proceed to STEP 4



STEP 4
Check location of the decoder and router.
a. If nearby (within 1.5m) - Try connect to box from router using LAN cable.
b. If far (more than 1.5m) / No LAN cable - Proceed STEP 5



STEP 5
Reboot router, modem and decoder.
If issue persist, please try again after 30mins to 1 hour. Connect to live agent if persist after 30 mins to 1 hour.

Astro's Plug & Play Box is our latest box where users can enjoy the latest Astro box simply by connecting it to the TV and internet. There is no longer a need to schedule or pay for an installation. By connecting your Plug & Play Box to home broadband, you will be able to-do the following:

• Watch your channels over the Internet. No more rain fade!
• Never miss your favorite shows again as you can stream LIVE events from the beginning, or simply pause and resume the program as you wish.
• Access a library of over 110,000 videos on demand. Catch-up or binge-watch full episodes whenever you like.
• Access your recordings anytime on TV or the Astro GO app via Cloud Recording.

Other features include pause on TV and continue watching on the Astro GO app, enhanced search capabilities and more.

No, customers are only allowed to choose ONE billing option (either Paper Bill or E-bill or SMS bill). However, customers who opted for Paper Bill will still be able to check their bills through Astro Self-Service Portal, IVR, Channel 200 and WhatsApp.

Connect your Ultra Box/Ulti Box today and get the full value for your subscription. We believe we can provide you the best entertainment experience in Malaysia, and it all starts with connecting your box to the internet.

Want to enjoy these features for free?

• Continue watching Astro even when it’s raining.
• Binge-watch and catch-up to 110,000 videos on-demand from Malaysia, Hollywood, Korea, China, Bollywood and more anytime.
• Create multiple profiles in your house to enjoy a personalized Astro experience, with shows recommended to you based on your interest. There is a Kids-friendly version for your little ones as well.
• Rewind, pause and fast-forward shows and matches so that you will never miss another moment.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Scroll to Network Settings and press "OK". Select New Wi-Fi Connection and press "OK".

‍

STEP 4

Select your Wi-Fi network and press "OK". Please enter the password to connect to your network.

STEP 5

You have successfully connected when this screen appears.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/ laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/ laptop].
2. You may open any web browser such as  Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)

Username: admin
Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the  configuration.

i. On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab.

ii. Please ensure Wireless RF Mode is Enabled.

iii. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

iv. Click Submit. Router will auto reboot and connection re-establish after few minutes.

• Bundle Packs with Chinese Favourites: If you are currently on the Chinese Favourites selection, your selection will switch to Viu Premium at no additional cost progressively from 1 April 2024. Not to worry, you may still manually switch to other Asian Favourite selections if you wish via the My Astro app.

• Chinese Favourites Add-ons: There will not be any changes to your current subscription pricing. Furthermore, your subscription will now include additional channels on a free preview basis.

• Old Packs: There will not be any changes to your current subscription pricing. However, as we have recently made adjustments to the channel lineup in our packs, please call us at 03-7481 1000 (Monday to Friday, 9AM – 6PM exclude public holidays) to find out how you get more value from your subscription.

STEP 1

Identify your remote control:

a)   Remote control with Astro logo at the bottom of the remote, proceed to STEP 2.

b)   Remote control with Astro logo at the top of the remote, proceed to STEP 4

‍

STEP 2 (Astro Logo at the bottom of the Remote)

On your remote, press the “set tv” button and set tv instructions will be displayed on top of your screen:

‍

STEP 3

Follow the steps appear on the TV screen to sync your Astro remote and complete the setup.

‍

STEP 4 (Astro Logo atthe top of the Remote)

Press and hold “tv input” key on bottom left of the remote for 3 seconds until the LED blinks twice.

STEP 5

Enter the 2-digit TV Code of your TV Brand and the LED will blink twice:

‍

STEP 6

Try out the TV controls (TV Standby or adjust Volume) to check if they are working correctly.

‍

STEP 7

Press ok and wait for the LED to blink twice to save the settings.

1. Unifi netis brand

The following shows an Interface based on Unifi router

1. Launch Web Browser and enter the default's gateway's IP address (192.168.1.1) in the address bar.

1. Enter Username and Password.
   1. Username = tmadmin
   2. Password = Adm@xxxx (xxxx refers to last four digits of MAC address)

1. Choose WLAN -> wlan0 (2.4GHz) Basic Setting. Note down on SSID.

1. Choose WLAN -> wlan1 (5GHz). Compare SSID with previous SSID.

1. If SSID for wlan0 (2.4GHz) and wlan1 (5GHz) are the same. Change wlan1 (5GHz) SSID by adding number 5(i.e. ifuni_5G) to differentiate from 2.4 GHz. Click Apply Changes.

Note: Connection to Wi-Fi may be temporarily loss while the changes is updated.

Broadband Deal bundle are recommended packages offered to customers with higher rebate as compared to Broadband Non-Deal bundle.

Yes, you may terminate the service, however an early cancellation fee will be applied for termination/cancellation within 24 months. Please refer to the Astro Fibre's cancellation details.

For Residential Astro Pay TV customers: Yes, you are allowed to change your package to the one that best suits your entertainment needs. You may make the following pack changes:  

1. Pack upgrades

1. Movement within Entertainment, Movies or Sports (e.g., switching from Sports to Entertainment)

1. Movement within Premium pack (to a different combination of content)

For these changes, you will remain on same contract duration, or you can choose to change to longer commitment. If you downgrade your packs, you will be charged a cancellation fee for pack, and you can then choose a new contract for the new pack. Kindly note additional contract details for Disney+ Hotstar and Netflix.  

(Please refer to the section "Changes to your Astro Contract" for more details)

At this point in time, the Disney+ Hotstar app on the Ultra or Ulti Box does not support Dolby audio. We are working to enable this in a future update. 

Yes, Astro is bounded by the PDPA act. All information received will be used in accordance with our Privacy Notice.

To set up a Mesh WiFi network around your house, the Mesh unit will need to be paired with the WiFi router. Steps to pair these two devices are as follows:

i. Place the Mesh unit close to the WiFi router (within 2 meters) and power it on

ii. After the Mesh unit starts up, press and hold the WPS buttons of the Mesh unit and the WiFi router for 3 - 5 seconds in turn within 2 minutes

iii. After the WLAN and Internet indicators of the Mesh turns steady blue, the Mesh is connected to the Internet

iv. Move the Mesh to the desired place where you need to expand WiFi and power it on. After the Internet indicator turns steady blue, WiFi is expanded successfully.

Astro does not provide installment plan facilities. You are advised to pay your charges before the due date, as per your monthly bill statement.

You may proceed with the following troubleshooting steps and it shouldn't take you much longer than 15 min

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Yellow port at Tplink Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to tplinkwifi.net and to access to below login page. Type the Username and  Password, then click "Login".

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your  router previously, the password may be different.

For example, below is the login details of the above router:
 

Username: admin

Password: TIMECE24
 

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, choose Advanced and click the Wireless tab on the left menu. Then, select Wireless Settings from the sub menu. Below screen will appear for 2.4GHz selection.

i. Please ensure to tick Enable Wireless Radio function.

ii. To change the channel, click the  drop-down arrow for Channel, then select your desired channel.

Choose between 1 to 13 (Suggested  channels : 1,6,11). Then, click "Save" for the changes to take place.

iii. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

iv. Next, select 5GHz to make changes on the wireless channel for 5GHz.

v. Click the drop-down arrow for Channel, then select your desired channel from the selection.

vi. Click Save for the changes to take place. The router will auto reboot and connection will re-establish after few minutes.

Yes, provided that your Plug & Play Box has not been activated and no later than 7 days upon receiving both the Plug & Play Box and Astro SIM card. In the event that you have activated your Plug & Play Box and wish to cancel, a contract penalty fee will apply.

We will reach out to you for a suitable time to pick up the Plug & Play Box and Astro SIM card.

STEP 1

Check on your TV input to ensure correct input selected.

If issue remains, switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Unplug the HDMI cable from your box and plug it back in securely.

STEP 3

Switch on the power for your box and make sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 4

Turn on your box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form with the error details and provide  sim card number for assistance.

Currently, Maxis, Digi, Celcom, TuneTalk, U-Mobile, Yes, XOX and Webe.