Tap on the "Account' screen on the navigation bar and scroll to the "Subscription' section. Tap on "TV Pack' to view your pack, box, multiroom, and Astro GO information.

STEP 1

Identify your remote control:

a)   Remote control with Astro logo at the bottom of the remote, proceed to STEP 2.

b)   Remote control with Astro logo at the top of the remote, proceed to STEP 4

‍

STEP 2 (Astro Logo at the bottom of the Remote)

On your remote, press the “set tv” button and set tv instructions will be displayed on top of your screen:

‍

STEP 3

Follow the steps appear on the TV screen to sync your Astro remote and complete the setup.

‍

STEP 4 (Astro Logo atthe top of the Remote)

Press and hold “tv input” key on bottom left of the remote for 3 seconds until the LED blinks twice.

STEP 5

Enter the 2-digit TV Code of your TV Brand and the LED will blink twice:

‍

STEP 6

Try out the TV controls (TV Standby or adjust Volume) to check if they are working correctly.

‍

STEP 7

Press ok and wait for the LED to blink twice to save the settings.

The promotion period of Astro Fibre’s Speed Upgrade Campaign is from 24 November 2023 until 31 May 2024.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)
 

Username: admin
Password: admin (or time123)

 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

• On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab

• Please ensure Wireless RF Mode is Enabled.

• Click the drop-down arrow for Channel, then select your desired channel.
• Choose between 1 until 11 (Suggested 1,6,11).

• Click Submit. Router will auto reboot and connection re-establish after few minutes.

The change in due date to 25 days after your billing date is to ensure that your transactions will be processed in a timely manner and subsequently ensure you will enjoy uninterrupted viewing. Please be assured that this change will not affect your monthly bill amount. Kindly check your latest monthly bill statement for more details about this revision.

This exercise currently only affects person-to-person SMS with URL links. However, the blocking of SMS sent by businesses via short codes such as 6XXXX, 3XXXX, 2XXXX and 1XXXX will be implemented at a later phase. In response to this government initiative, Astro customers will no longer receive SMS bills effective 1 August 2023. This change will be carried out in phases.  

Please switch your preferred Bill Delivery Method using our self-service portals via My Astro Web or My Astro app. Please click here to download the app on your mobile device or login to My Astro Web.

Deposit of RM500 (Maxis) and RM300 (Allo) is payable by new subscribers (non-Malaysian). The fee will be reimbursed when service is terminated.

No deposit required for all existing Astro customers and new subscribers (Malaysian).

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to LNB Setup and press “OK”.

STEP 5

Tuner Settings screen will be displayed accordingly.

STEP 6

Select LNB Type connected to your box.

STEP 7

Navigate to Next and press "OK" to confirm your selection.

STEP 8

Select this as the Entry Point and press "OK"  to confirm your selection.

STEP 9

Navigate to Next and press "OK" to confirm your selection.

STEP 10

Signal reading results for Tuner 1 screen will be displayed accordingly.

Press right to navigate to Tuner 2.

STEP 11

Signal reading results screen for Tuner 2 will be displayed.

Then navigate to Finish and press "OK" to complete the setup.

Customers subscribing to the following Astro packs will get to automatically enjoy Disney+ Hotstar as part of their newer, bigger and better packs

• Movies Pack
• Movies Plus Pack
• Premium 1
• Premium 3
• Platinum Pack

Customers with any of the above subscriptions with an Ultra or Ulti Box will also be able to enjoy Disney+ Hotstar on their big screen TV via their Astro Box, in addition to disneyplushotstar.my  and the mobile app. Please click here on how to access Disney+ Hotstar on the Ultra/Ulti Box.

 

Astro customers who are not on the above Packs may upgrade to the Movies, Movies Plus, Premium 1, Premium 3 or Platinum Pack to receive access to Disney+ Hotstar at no additional cost. Alternatively, customers may visit www.astro.com.my/disney to subscribe to Disney+ Hotstar Premium through a 3-month plan via Astro at RM54.90 (NP: RM79.90 quarterly, Astro customer may see up to 30% savings in their Disney+ Hotstar Premium subscription)

 

For more information, please visit www.astro.com.my/disney. If you need further help, please WhatsApp “DH Help” to Astro or call them at 03-9543 3838 for assistance.

Please visit http://help.netflix.com to call or start a live chat with Netflix's customer support agents. You will be assisted to unlink your Netflix account from your Astro subscription. After the process, you may link another Netflix account to your Astro subscription.

Please contact us through one of our platforms found here or Self-serve by logging in to Astro Self-Service Portal within 3-7 days before moving out and we will sort everything out for you!

Please ensure that you have subscribed to PVR recording service.

If you're subscribed to PVR recording service, follow below steps.

‍

Let's  check your hard disk connectivity.

STEP 1

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4

From the General tab, take a look at the HDD Status.

If status is "Connected", press red button to reboot you decoder.

Wait until the box is on, then try to record any program.

‍

If issue persist, please submit the issue on our Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

If status is "Disconnected", please submit your Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

Astro Fibre Bundle is a subscription service of broadband together with your desired Astro TV package, while Astro Fibre is a service that allows you to subscribe to Astro Fibre broadband only.

STEP 1

Switch OFF the power of your Ultra / Ulti box and make sure that the adapter's power light is off.

STEP 2

Switch ON the power of your Ultra / Ulti  box and make sure that the adapter's power light is on.

STEP 3

On your remote control, press the standby button repeatedly until the Startup Options appear on TV.

STEP 4    

Press "1".

‍

STEP 5

Press "1".

‍

STEP 6

The Software Update progress screen will appears.    

The update will take 10 - 15 minutes to  complete.    

Please be patience.

Yes, Mesh WiFi add-on is available for both Astro Fibre Bundle and Astro Fibre subscription.

Astro Quick Pay is a convenient method to check your Bill Summary, Account Status and pay Astro bills at your convenience with immediate payment posting, right from home. Visit Astro Quick Pay to pay your bill now.

We would need you to  run few tests in order for us to understand your issue and to assist you in fixing the problem.

You may proceed with the troubleshooting steps below which should not require any longer than 15 minutes.

1. Please run each of  the tests according to your your Laptop/PC Software.
2. Compile the pictures / screenshots of  your test results in one file (i.e Microsof Word document, PDF file) and attach them in the Support Ticket below in order for us to assist you further:
   • List of websites effected.
   • Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.
   • Run the Traceroute Test - Please click here for Traceroute Test guideline.
   • Run the Ping Test -  Please click here for Ping Test guideline.
3. Once you/ve gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

We try to make as many movies and TV shows available for download. However, for some titles, while we may have the rights to offer them via streaming, we may not be able to offer them for download.

STEP 1  

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3  

Navigate to STB Diagnostics and press "OK".

STEP 4    

Select Advanced Diagnostics and press "OK".

STEP 5  

Details information of Advanced Diagnostics screen will be displayed.

STEP 6    

Press down arrow on your remote to get more information.

By changing from a higher contract duration e.g., 24-months commitment period to lower contract duration e.g., 12-months, a proration of the cancellation fee will be applicable whereby you will be charged per contract's month balance against the maximum cancellation fee agreed upon during sign up for the offer.

A proration of the cancellation fee will be applicable whereby you will be charged per contract's month balance against the maximum cancellation fee agreed upon during sign up for the offer.

You will start a new contract with 12-months commitment and receive the corresponding discount for that duration.

Check out how a cancellation fee is calculated with examples via this link:

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please ensure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Intermittent internet connection using Wi-Fi

1. Router Positioning
   Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
   
    i) High vs. Low
   Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   
   ii) Concrete & Metals
   Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   
   iii) Distance to Router
   The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
   
   Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.
   
    

2. Wireless Interference & Noise
   You've probably never noticed but there are wireless signals all around you wherever you go and they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.
   
   Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:
   i) Microwaves
   ii) Bluetooth Devices
   iii) Cordless Phone
    

3.  Surrounding Wi-Fi signals
   A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel  overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many  routers within close proximity. Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

4. Usage
   More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

Please make sure that:

1. You are logging in with the correct registered Astro ID (email or phone number) and password. If you can’t remember your password, please proceed to use the “forget password” function.
2. You have an Astro ID that is linked to an Astro account. (note: NJOI – linked users will not be able to log into Astro GO)
3. Your Astro account is active and not under suspension.

If the above points have been met, you may try some quick solutions below:

1. Clear the cache on your browser or app.
2. Check if you have the latest version of the browser or app.
3. Log out and log back into the browser or app.
4. Relaunch the browser or app.
5. Restart your mobile device.
6. Restart your internet connection.

Your existing contracts and corresponding rewards including but not limited to discounts/rebates will be removed with no penalty applied and replaced with the new contracts associated with the new packs. Exception applies to Disney+ Hotstar (3-Month Pack) and Multiroom campaigns in which remaining contract durations will be brought over if the subscription is continued or penalty will be applied upon discontinuation of said subscriptions.

Yes, you will. Customers who purchased Astro First / Astro Best / Pay-per-View event in February 2024 with a viewing period in March 2024 will be charged an 8% Service Tax in their next bill.
 

For Platinum Pack and Multiroom Smart TV customers, Astro GO+ is included in your subscription at no extra charge. For customers on other packages, you will be able to add-on Astro GO+ to your subscription for RM 5.99/month.

You may use the same feedback form and choose below options.

Category: I would like to request for refund

Sub Category: Request for Refund

Connect your PVR to Wi-Fi and enjoy access to our library of Video On Demand. Replay old seasons, catch-up latest episodes of your favourite shows, anytime you want. To connect your PVR, follow the steps below:

STEP 1    

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2    

Navigate to SETTINGS and press “OK”.

STEP 3    

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4  

Navigate to Network and press "OK".

STEP 5    

Navigate to Wi-Fi and press "OK".

STEP 6    

Select New Connection and press "OK".

STEP 7    

Select your Wi-Fi network and navigate to "Connect".

STEP 8    

Please enter the password to connect to your network and press "OK".

STEP 9    

You are successfully connected when this screen appears.

STEP 1    

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Take a look at the Smart Card Status.

(i) Head over to My Astro Portal and go to 'Bill & Payment'. Click on 'Payment History'
(ii) Contact us via one of these platforms. Please ensure you include your Astro Account Number.

Mesh WiFi network refers to a unified wireless network that is formed by utilizing inter-connected WiFi nodes (Mesh devices) placed throughout the house.

You may register for auto-debit via: -

‍

1.My Astro website.

‍

‍

2.MyAstro App.

‍

‍

3.Any of our AstroExperience Store.

STEP 1    

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Take a look at the HDMI Connection Status.

If you are already subscribed to the Movies/Premium 1/Premium 3/Platinum Pack, you are automatically entitled to access Disney+ Hotstar. Therefore, you will not be able to add on the Disney+ Hotstar 3-months pass. 

Advance payment can be made via credit/debit card or online banking.

Yes,existing Astro & Broadband customers within contract or out of contract can subscribe to Astro Fibre offer. The 24-month contract will be renewed.

However, your contract with Maxis/Allo needs to be terminated before signing up to this offer. An early cancellation fee applies if you are still within contract.

‍*Subject to Terms &Conditions of your contract

Please check your internet speed and connection status via internet connection test. If your internet is working fine and the issue persists, proceed to submit report via WhatsApp or Feedback Form.

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which could cause the issue.

3. If issue persists, submit your Feedback Form for further assistance.

Yes, you may cancel your Astro Fibre order before service activation, however, kindly note that there is a cancellation charge of RM212 (inclusive of SST) for any service cancellation done 48 hrs before scheduled appointment.

It will take around 10 to 15 minutes before you are able to view your purchase.

If you have a random Astro power cable, remote control or old box lying around at home, you are required to discard them only at registered collection centres for proper handling and management of e-waste in an environmentally sound manner. Click here to find a registered collection centre near you.

For all recycling-related questions, please click here.

Yes, until 31 August 2022, customers can subscribe to the Movies Pack for only *RM59.99/month or the Platinum Pack for only *RM99.99/month for 6 months as well as the Premium 1 or Premium 3 Pack for only *RM99.99/month for 6 months until 30 October 2022 and be entitled to access Disney+ Hotstar as part of their Astro subscription. To find out more about our latest promotions, please visit promotions.astro.com.my. 

The RM15 monthly rebate (before Govt. Tax) will be applicable to all on-going Multiroom Smart TV subscriptions until further notice. However, in the event of rebate expiry, Astro will notify impacted customers in advance via email or SMS. To update your contact details, please reach out via a feedback form here.

If you need further help with the Astro Fibre app, you may call our Customer Contact Centre at 03 - 9543 1543 and an Astro agent will be available to assist you immediately.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be experiencing this problem.    

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be experiencing this problem.    

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.