You can proceed with below troubleshooting if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4

Refer to the signal strength % shown on the top left of your screen.

If it is 65% or higher, please take the screenshot and submit your Feedback Form.

If it is below 65%, please go to Step 5.

STEP 5

Switch off the power for your box and make sure that the adapter’s power light is off.

‍STEP 6

Unscrew the satellite cable from the box and pull it out.

STEP 7

Plug the satellite cable back into the box and screw it back securely.

STEP 8

Switch on the power for your box and make sure that the adapter’s power light is on.

Please wait for 5 minutes.

STEP 9

Turn on your box. You should no longer be experiencing this issue.

‍

If issue persist, please submit the issue on our Feedback Form and attach a picture of your General tab of the STB Diagnostics for assistance.

‍

Centralized Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the blue port at Cisco Router and direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

4. Type the Username and Password as below. Then click OK. (These are the defaults, if you have done previous configuration on your router the password may be different).
 

Username: admin

Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

i. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

ii. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

iii. Leave the Channel Width set to 20MHz Only.

iv. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

v. Click Save Settings to apply your changes. Router will auto reboot and connection re-establish after few minutes.

Unfortunately, you will no longer be able to access Disney+ Hotstar via Astro if you cancel your Astro subscription with Disney+ Hotstar entitlement. 

Upon completion of the termination process, customer will receive one last closing bill stating the total amount due to Astro according to their billing option.

For customers who had opted to switch their billing option to e-bill or SMS bill, they will receive their final bill accordingly.

For customers who opted for paper bill, they will receive the final bill via paper bill. (The Paper Bill Charge will be applied).

Yes, the Multiroom (Smart TV) will utilise one (1) of your Astro GO concurrency.

Customers subscribing to Multiroom (Smart TV) can enjoy access up to 4 concurrency (watch 4 screens at the same time) which is shared across one Smart TV device and 3 mobile/laptop/tablet device(s) as Astro GO+ is complimentary with a Multiroom (Smart TV) subscription.

Your documents will be handled in compliance with standards set by PDPA (Personal Data Protection Act 2010) and will not be used for other means without your specific consent.

STEP 1    

Press "HOME" button on your remote control.

STEP 2  

Navigate to Settings and press "OK".

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Take a look at the Smart Card Status.

STEP 1    

On your remote, press the ... button and the Channel Guide page will be displayed on your screen.

STEP 2    

Select the channel you would like to unlock and press "OK".

STEP 3    

Select "Unlock Channel" and press "OK".

STEP 4    

Enter the PIN to unblock the channel.

STEP 5    

You are successfully unlocked the channel when this screen appears.

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

2. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user

Password: user

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click More to configure the WiFi parameters.

6. From the left menu, select WLAN and choose Wi-FI Advanced Network to access the screen below.

7. To change the channel on 2.4 GHz and 5 GHz, click the drop-down arrow for Channel, then select your desired channel.

8. Then, click "Apply" for the changes to take  place.

For self-installation, in your first bill upon activation of your Plug& Play Box, the activation fee will be included as a separate line item in your bill alongside the subscription fee.

If you choose to install the Plug & Play Box via installer, you can pay the installation fee and activation fee directly to the installer upon installation. This will be reflected in your next bill itemised as setup fee.

The New Astro First serves as the one-stop, ultimate home cinema offering the biggest and latest local and international blockbuster films where you can:-

• Enjoy value for money viewing for local and international movies from only RM15* per movie or RM17* for UHD movies (*excluding tax).
• Stream each rented movie for as many times as you like within 48 hours* (*unless stated otherwise) anytime, anywhere via On Demand on your Astro Box or Astro GO.
• Watch local/regional movies or international movies from Hollywood studios as recent as 2 weeks or 3 months respectively from Malaysia's cinematic release, in addition to exclusive titles only available on Astro First.

STEP 1
Check the Audio settings on your box and set to Auto.
Refer guide to change Digital Audio Settings.

STEP 2
If issue persist, check if there is any 3rd party device (sound system/hdmi splitter) connected between box and TV.

STEP 3
If using 3rd party devices, bypass/remove 3rd party device and make sure HDMI cable connected directly from box to TV.

STEP 4
If issue persist, connect to Live Agent via WhatsApp for help.

When Band Steering is enabled, only one SSID network name with one password is available. Example:

i.SSID: SSID, Password: 12345678

Yes. As a Sports Pack customer, you will get access to Liga Malaysia as well as a variety of local and international sporting events as part of your subscription.

Step 1: Open your My Astro app

Step 2: Select "Astro Rewards"

Step 3: Scroll through your rewards to see what you're entitled to

Step 4: Select the rewards that take your fancy and follow the instructions stated on how to redeem them (redemption instructions may vary based on reward)

Astro is no longer updating the software in non-Ultra/Ulti Boxes as they have reached their end-of-life cycle. Therefore, non-Ultra/Ulti Boxes will maintain their current classification systems. Nonetheless, you may refer to content.astro.com.my for all the updated age ratings. Please refer to the table below to see the difference in classification systems between our platforms:

After order submission, the Plug & Play Box and Astro SIM card will be couriered separately to your service address. The delivery dates with the tracking numbers will be communicated via SMS.

The Plug & Play Box and Astro SIM card should arrive within 3-working days after your order submission. You may self-install your box by following the guide here.

Please contact us through one of our platforms found here or Self-serve by logging in to Astro Self-Service Portal within 3-7 days before moving out and we will sort everything out for you!

STEP 1

Check on your TV input to ensure correct input selected.

If issue remains, switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Unplug the HDMI cable from your box and plug it back in securely.

STEP 3

Switch on the power for your box and make sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 4

Turn on your box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form with the error details and provide  sim card number for assistance.

‍

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and  direct to computer/laptop].

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.254 and below page will appear.

‍

‍

If below box appear, please enter required details as below:

‍

‍

USERNAME:  Administrator

PASSWORD: (ACCESS KEY AT THE RGW STICKER)

(These are the defaults, if you have done previous configuration on your router the password may be different)

‍

4. Once enter into the page ‘’TECHNICOLOR TG784N V3’’, you may follow below step for the wireless information.

i. Click "Configure”

‍

ii. Once clicked configure button, below screen will appear.

A. This is your current password. Please delete and enter the new password.

B. Once completed the selection; click the "Apply" button. Router will auto reboot and connection re-establish after few minutes.                      

Please re-connect your wireless using the new password.

If you're trying to visit a website and it won't load, but others do, there could be a variety of causes. If the site itself is down, there's not much you can do but wait.

If you can load the site on other computers or devices (make sure you try different means of connecting to the internet), there may be an issue with your computer or network.

There are some quick fixes that will solve most problems, but you may have to get your hands a little dirty.
 

1. Try loading the site on a different device.
   • Try loading the website on your phone or on another computer. If the website loads on the other device, the problem lies with your computer.
   • If the website doesn't load on another device, the problem is either with the network
2. Restart your computer.
   • Oftentimes, a simple reboot will fix the problem you're having. Reboot your computer and test the website again.
3. Try loading the site in a different browser.
   • There may be some settings configured incorrectly on your browser. Try a different web browser to see if you can load the website.
4. Temporarily disable your antivirus program.
   • Your antivirus software may be interfering with your ability to load certain websites.
   • Try disabling the software and then loading the site again. Make sure you enable it again once you have identified the problem.
5. Reset  your modem and router.
   • Traffic to or from a certain website may be getting tripped up by your modem or router. Resetting these devices may allow you to access the website again.
6. Check your computer's date and time settings.
   • If your date or time is set incorrectly, you may not be able to connect to secure (https://) websites.
   • Check your computer or mobile device's clock to make sure that it is set to the correct time and date.

i. List of websites effected.
ii. Run the Speed Test via LAN (cable) and Wi-Fi connection - Please click here for Speed Test guideline.  
iii. Run the Traceroute Test - Please click here for Traceroute Test guideline.
iv. Run the Ping Test -  Please click here for Ping Test guideline.

Once you've gathered all the results, kindly send them all through the Feedback Form below.

Quick Info
A Speedtest is a service that provides free analysis of Internet access  parameters, such as connection data rate.
A Ping Test shows how long it takes for packets to reach host.    
A Traceroute Test traces the route of packets to destination host from our  server.

Unfortunately, you can't. My Astro is an easy-to-use, free mobile phone app and responsive web portal that helps Astro customers manage their Astro accounts. Astro customers can watch their favourite shows anytime, anywhere using the Astro GO app which is included in their subscription.

You may report the incident on WhatsApp at 03-9543 3838 by typing PNP and our access our user guide or request for further help from our dedicated agents. Please have your Airway Bill tracking numbers ready for validation. If a replacement box/Astro SIM card is deemed necessary, a new Box and a new Astro SIM card will be couriered to your service address.

Your bill statement will include details of your monthly subscription charges; e.g. charges for your chosen Astro packages and Broadband service. It will also show the time period of which your first bill will cover, as well as indicate how much the total charges are and when the payment due date is.

To check your contract, please visit My Astro.

Unfortunately, your Disney+ Hotstar access with Astro will be terminated as well. 

1. Router Positioning
   • Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
   • High vs. Low
     • Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals
     • ​Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for WiFi signals to penetrate.
   • Distance to Router
     • ​ The further away from your router you  get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
     • Otherwise, you should place your  router near the center of your home. After all, WiFi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.
2. Wireless Interference & Noise
   • You've probably never  noticed but there are wireless signals all around you wherever you go and  they're passing through you all the time. From where? Electronic devices,  WiFi routers, satellites, cell towers, and more.
   • Although WiFi is  supposed to be on a different frequency than most of these devices, the  amount of radio noise can still cause interference. Some common causes of interference include:
     1. Microwaves
     2. Bluetooth Devices
     3. Cordless Phone
3. Surrounding Wi-Fi signals
   • A truth of the modern world is that every  household has their own WiFi network, which can cause issues with channel overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many  routers within close proximity.
   • Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels  for you automatically, but sometimes it's better to investigate and find the best channel yourself.
4. Usage
   • More likely, however, is that the people  on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/ Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

Yes, a third party is allowed to make the advance payment on your behalf. In the case of refund, the amount will be returned to the owner of the third-party account (source of payment).

Please update your auto-debit payment details via My Astro Portal.

Astro introduces the new Ulti Box with a redesigned new interface, Cloud recording feature, enhanced search capabilities and more. Just connect the all new Ulti Box to the Internet and take control of your entertainment and stream up to 110,000 videos on demand, anytime. 

‍

The features of the new Ulti Box include:

·      New Home Screen - Everything you see is yours

·      Discover Video on Demand (VOD) - Discover 110,000 videos, stream anytime, anywhere

·      Search - Search for your favorite show or video faster and easier

·      Play from Start - Missed the start of the show? Just restart.

·      Stop Here, Continue There -Stop on one screen and continue on another device

·      Multi-Screen - Stream seamlessly across any device

·      Cloud Recording - Record all the programmers you want at the same time

.      **Continuous viewing - Enable to continue watching your favorite shows during raining.

‍

We recommend an Internet speed of 10Mbps and above for optimal access to cloud recording, streaming on demand videos and search functions. 

Note: ** Except 4K UHD, Astro First and all radio channels

Create your Astro ID anytime by following these simple steps: 

• Step 1: Fill in your details at astro.com.my/astroID
  
  

There is no contract for this subscription.

Yes, you will enjoy an Ulti box when subscribing to Primary/Entertainment/ Movie Pack OR an Ultra box when subscribing to Sports/Sports+/Movies+/Premium 1/Premium 2/Premium 3/Platinum Pack.

You will get FREE installation for both Ultra/Ulti box upon signing up with Astro & Broadband.

Yes, you can switch to Astro Fibre and all the devices provisioned will be maintained (Fibre modem & WiFi router) with the new Astro Fibre subscription. However, your Astro TV package will be removed/terminated.

An early cancellation fee will be applied if you are still within the 24-month contract. Please refer to the Astro Fibre's cancellation details.

STEP 1

Press any button on your Astro remote.

INDICATOR: LED blinking 3 times / NO LED blink

SOLUTION: Replace new battery

STEP 2

Check if you can change channel using  your Astro remote control.

If issue remain after the battery replacement, try changing the channel manually directly from box front panel (If any).

If it's working, you might need to replace your Astro remote.

This might be due to a faulty Astro remote.

You may purchase it directly from Astro Exclusive Partners.

If confirm no issue with remote control, please refer to Decoder Hang at Channel troubleshooting steps here.

Step 1: Download the My Astro app from either the App Store, Google Play or HUAWEI AppGallery.

Step 2: Sign in with your Astro ID.

Step 3: Select "Rewards" on the home screen to get started.

Watch this tutorial to learn how to create your Astro ID.

• With numerous OTT entrants, consumers are suffering from subscription fatigue. In fact, they are looking for a one stop shop platform where OTT services are integrated in one place.

• Astro offers flexibility and convenience with new packs where customers can get the convenience of accessing a variety of content via Ultra Box as the single remote-control solution.  

• In addition, there will be cost savings for Astro customers to purchase both Netflix and Astro together. Even better deals available if customers also subscribe to broadband for a better-connected experience.

Customers with HD boxes can subscribe to the All-New Astro Pack without a box upgrade except if the customer request to move to OTT bundled pack which is mandatory to upgrade to Ulti or Ultra. 

Note: OTT is referring to either Netflix, D+H or both.

Currently Astro GO is only available in Malaysia. You will not be able to access it if you are overseas.

Please follow the steps below:

Step1: Fill in Merge/Split Equipment Form (Part A & Part B)

Step2: A full payment to be made on any outstanding balance for all related accounts (if any).

Step3: Submit all documents via feedback form or walk in to nearest Astro Customer Service Centre (CSC).

Step4: Customer will expect a call from our validation team (Note: Turnaround time for merge/ split of account is 3-5 working days upon receiving all complete documentation).

Note:

1. There might be a loss of transmission during the processing of transfer equipment ownership, split or merge of equipment.

 Activate your Disney+ Hotstar access with your Astro subscription, using the steps below:

• Step 1 - Create- and verify your Astro ID at astro.com.my/astroID. If you already have an existing Astro ID, go to Step 2.

• Step 2 - Goto astro.com.my/Disney. Login with your Astro ID, activate with your mobile number and verify with a one time passcode (OTP) sent to your mobile number.

• Step 3 - Download the Disney+ Hotstar app or login via web, and sign in with the mobile number provided in Step 2. Start streaming!