Yes, existing non-Primary Pack customers who add on 50Mbps to their subscription will get to enjoy high speed broadband for only RM60/month and a free speed upgrade to 100Mbps for 24 months. Please note that a new 24-month contract will start upon successful installation.

Visit our page to find out about our new packs.

Mesh WiFi network refers to a unified wireless network that is formed by utilizing inter-connected WiFi nodes (Mesh devices) placed throughout the house.

You will be contacted by Astro via SMS/call at the end of your 24 months speed upgrade period. Customers who choose to remain the upgraded speed after 24 months will be charged as per the monthly subscription fee of the upgraded speed plan from the next month onwards and customers who choose to downgrade to their initial subscribed speed plan will not be charged any additional fees.
 
Situation 1:
Customer is subscribed to the 50Mbps Astro Fibre plan and is entitled to receive a free 100Mbps speed upgrade for 24 months. If the customer chooses to downgrade back to 50Mbps at the end of the 24-month period, no additional charges will apply.
 
Situation 2:
Customer is subscribed to the 100Mbps Astro Fibre plan and is entitled to receive a free 500Mbps speed upgrade for 24 months at RM129/month. If the customer chooses to remain with the upgraded speed of 500Mbps at the end of the 24-month period, they will be charged RM189/month* from the 25th month onwards.
 
*This price might differ depending on the offer or promotion
 

Of course not! It is a value-added service introduced for your convenience.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the blue port in Cisco Router and direct to computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

‍

‍

4. Type the Username and Password as below. Then click "OK". (These are the defaults, if you have done previous configuration on your router the password may be different).

Username: admin

Password: admin (or time123)

5. Click "OK" when a Warning prompt that says,” Using this advanced utility to change your router settings could disable your network” appears. Below display will appears.

6. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

7. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

8. Click Wireless Security to view the security settings of your wireless network. Take note of the Security Mode and the Passphrase.

For the example below, the Security Mode used is WPA2/WPA Mixed Mode.

The Wireless name is called Network Name (SSID) and the Passphrase is your wireless password.

‍

9. Now that you have the Wireless name and Password, you are ready to connect your wireless computers and devices to the network.

10. You may change the Network Name (SSID) and the Passphrase to follow your preferences and please ensure save the changes made. Please reconnect to the new wireless name with the new password once completed.

‍

You can add a new Netflix account to your bill through CH 741 or clicking the Netflix button on the remote control. Please enter the email address you would like to use for Netflix subscription and ensure the Billing partner is Astro.  

If you would like to transfer your existing Netflix Account to be charged under Astro bill, please follow the steps below:  

1. Cancel your existing subscription with Netflix  

1. Once the remaining duration of your existing subscription has ended, you may proceed to subscribe for Netflix via Astro bill  

1. To subscribe, go to CH 741 and enter the email address used for your previous subscription with Netflix  

1. Once successfully completed, all existing settings and watching history on your Netflix account will be brought over  

STEP 1

Switch OFF the power of your Ultra / Ulti box and make sure that the adapter's power light is off.

STEP 2

Switch ON the power of your Ultra / Ulti  box and make sure that the adapter's power light is on.

STEP 3

On your remote control, press the standby button repeatedly until the Startup Options appear on TV.

STEP 4    

Press "1".

‍

STEP 5

Press "1".

‍

STEP 6

The Software Update progress screen will appears.    

The update will take 10 - 15 minutes to  complete.    

Please be patience.

We are thrilled to announce that as part of your subscription, you are able to enjoy exclusive coverage of live matches in HD on Astro channels, On Demand and Astro GO! This means that you'll have access to all the latest games, highlights, and analysis, right at your fingertips.

With this new addition, you'll be able to follow your favourite teams and players closer than ever before, keeping you up-to-date with all the action on and off the field. Whether you're a die-hard fan or a casual spectator, this new content is sure to provide you with endless hours of entertainment.

To ensure that we continue offering the best choice in sports content, our Sports Pack will now be priced at RM104.99/month (for 12 months contract) or RM99.99/month (for 24 months contract) and Premium Pack 1 will now be priced at RM139.99/month (for 12 months contract) or RM129.99/month (for 24 months contract) starting 9 February 2023, and this applies to all new customers. 

Note that there will no changes for existing Sports Pack & Premium 1 customers in 24 or 12 month contract being renewed before 1st June 2023.

We appreciate your continued support and can't wait for you to experience this exciting new addition to your Sports Pack subscription.

Please refer to the table below for the full revised pricing for the following packs:

We hope you continue to enjoy your Astro experience with us.
 

STEP 1    

On your remote, press the Home button and the menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3    

Navigate to Restore and press "OK".

STEP 4    

Navigate to Restore Factory Settings and press "OK".

STEP 5

Enter your PIN to access this setting. (Default PIN is 0000).

STEP 6    

Navigate to Restore and  press "OK" to  confirm your selection.    

Otherwise, navigate to Cancel, go back to remain the settings.

STEP 7    

Please wait while the box restoring defaults and will reboot once complete.

STEP 8    

Your box will automatically restart and display this screen.

Click here to follow New Installation Settings guide for Satellite

Click here to follow New Installation Settings guide for Plug and Play

Step 1: Visit Astro website at https://www.astro.com.my/

Step 2: Click "Login'

Step 3: After login, click the profile icon and select 'Manage Profile'. You may change your account password here.

Please refer to "Upon downloading the app, what do I do next?" question on this FAQ here or call us at 03-9543 3838 for any further queries.

For any access related queries on Disney+ Hotstar, please call or WhatsApp "DH Help

Starting 21 June 2022, all new digital sign-ups for TV packs on astro.com.my will now include access to the Astro GO app within an hour upon checkout of your first month subscription fees (excluding tax). Install the app on your smartphones, tablets or computers and you can start streaming even before your Astro box arrives!

1. Power reset (on & off) your Modem and Router.

2. Ensure standard physical connection (No 3rd party devices connected to decoder and modem).

3. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).

4. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

5. On the address bar, type https://testmyline.astro.com.my/ and below page will appear.

6.Click "GO", and the test will begin.

The test is completed once both download and upload speeds are displayed.

Sample of the Speedtest result is shown below.

**Please ensure the snapshot includes a time stamp and network used either LAN cable or wireless (as per picture above)

7. Kindly screenshot or take a picture of the result, name it as "LAN Speedtest" for test using LAN cable (wired connection).

8. Repeat the test once again using WiFi connection (Please unplug your LAN cable and connect via wireless connection using your SSID).

9. Screenshot or take a picture of the result, name it as "WiFi Speedtest".

We have discontinued offering the PVR box to our customers. You may opt to take up our latest 4K UHD supported Ultra Box instead. For more information, visit https://product.astro.com.my/box.

Alternatively, you may reach out to us at 03-7481 8000 for further enquiries or to sign up for the Ultra Box.

The speeds shown under “My Network Map” are the WiFi speeds of your connected devices based on factors such as signal strength, distance of devices from your router, obstructing objects etc. This function allows users to know the signal strengths achievable from every room in their house or any distance from their router, giving users accurate indication If additional mesh is needed or if the placement of their router requires adjustment.

However, the speeds shown under “My Devices” are the recent WiFi consumption of your connected devices, which allows you to monitor every user’s internet consumption in your household.

Astro wants to give our members the convenience of having all their favourite series, exciting originals, vernacular signatures, live sports and local blockbuster movies in one place. Astro customers will be able to enjoy greater convenience by having Netflix bundled with their Astro subscription, consolidating the subscriptions, and providing easy access for payment in a single bill, at the best value.

Customers who subscribe to the Movies, Premium 1, Premium 3 or Platinum Pack will be able to access Disney+ Hotstar immediately and start streaming all their favourite Global, Regional and Malaysian hits upon activation. 

You may click here to Login and proceed to secure your Astro ID by linking it to your Astro account. If you do not have an Astro ID, please follow the steps in below to create one. You may also choose to log in or create Astro ID with your social accounts (eg. Facebook, Google and Apple).

As a rule of thumb, this issue might happen when the devices are not equipped with minimum requirement above that supports the subscribed internet speeds:

• WiFi technology
• Network Interface Card (NIC)

As mentioned above however, it is important to note that despite meeting the device minimum requirements, it is not a guarantee that devices connected over WiFi will be able to achieve maximum subscribed internet speeds due to the following:

1. Bad WiFi signal quality and coverage across the area due to:
   • Distance from the RGW/Mesh AP with connected device
   • Obstruction within the house (walls, metallic surfaces)
   • Interference with other household appliances
2. Congested bandwidth
   • If there are too many devices connected to the WiFi network, then the bandwidth might be overloaded with traffic hence, slowing down the speed
3.  Devices are connected using WiFi instead of wired using LAN.
   • It is important to note that wired connection offers better reliability and speed over WiFi.
   • WiFi is more prone to interference compared to a wired connection which causes lower speeds and dropped signal.
4. Router Positioning: Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night:
   • High vs. Low: Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   • Concrete & Metals: Make sure your router isn’t blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   • Distance to Router: The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices. Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn’t make sense to put it at one end of the house.
5. Usage
   • More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   • Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.
   • If the problem persists, please run a Ping Test/Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances. Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Note:
Astro and its service providers will not offer any guarantees for compatibility of the customer's equipment (e.g., Personal Computer, Notebook, printers) nor provide on site troubleshooting for WiFi service issues related to the customer's equipment.

Astro GO+ is a service add-on that: 

• Enables the simultaneous viewing of Astro GO for up to 4 users/devices. 
• Increases the cloud recording storage from 200 hours up to 1500 hours. 

You have the liberty to manage device connection on your own.

Step 1:  Launch the app on your Smart TV.

Step 2: You will be able to see a welcome screen with a QR code and URL.

Step 3: Scan the QR code or go to astro.com.my/tvapp on your mobile and enter your unique code (e.g. FSJV-SMBS) displayed on the TV screen

Step 4: At the login page, you will need to log in with your Astro ID (registered email or mobile number) and password.

(If you do not have an Astro ID, click on "Create now" 

to sign up and link to your Astro account – check the following on the steps) 

Step 5: Once you have successfully logged in on your mobile, the Astro app will launch on your Smart TV screen. You can continue to browse and watch your favourite shows on the Smart TV.

All streaming apps willbe made available on the Ultra Box first, followed by the Ulti Box. If youwould like to upgrade to the Ultra Box, please visit product.astro.com.my/tv or reach us via WhatsApp by typing “Hi” at 03-9543 3838 forassistance.

If you choose to downgrade your packs or terminate Astro services before the end of your contract term, you will have to pay a cancellation fee. This cancellation fee is calculated based on your subscribed package, contract period and box type. If you cancel your service(s)/change your packages upon completion of your contract term, you won't have to pay any cancellation fee.

Astro does not provide installment plan facilities. You are advised to pay your charges before the due date, as per your monthly bill statement.

Step 1: Open your My Astro app

Step 2: Select "Astro Rewards"

Step 3: Scroll through your rewards to see what you're entitled to

Step 4: Select the rewards that take your fancy and follow the instructions stated on how to redeem them (redemption instructions may vary based on reward)

Firstly, you would have to retrieve your email address/mobile number. Please follow the steps in Q7 in order to do so. Then, follow the steps in Q5 and Q6 to check or update your contact details. Please use your updated email address or mobile number as your Astro ID to log in moving forward.

Note: Only Astro customers whose Astro ID is linked to their subscription can retrieve their Astro ID this way. Otherwise, you would need to create a new Astro ID.

Step 1: Separate Your Wi-Fi Network Name

First, you need to set up your Wi-Fi to Dual-band in order to be less susceptible to interference, and allows you to choose between the 2.4GHz or 5GHz bands when connecting a device. A Wi-Fi frequency of 5GHz is best when you are near your router, and 2.4GHz is best for when you are far from your router.

• Check the bottom of your router for a website or IP address, username, and password.

Below are details for a standard login based on a standard router issued by ISP (Telekom Malaysia, Maxis, and Time dot Com)

• Login to your account
• Identify your Wi-fi Settings (This could be in advanced settings)
• Identify both the 2.4GHz and 5GHz options.
• Split the signals by renaming the 2.4GHz and 5GHz signals respectively, and make sure both are enabled.
• For detailed instructions based on router model, on how to separate your Wi-Fi, click here and choose the option according to your ISP and router brand.

Step 2: Factory reset your Ultra Box by following the steps below.

a. Press the Home button on your remote

b. Go to your settings page

c. Scroll down and select Reset/Restore

d. Select restore factory settings and proceed

e. Enter your PIN to access restore factory settings (default pin: 0000)

f. Choose restore and wait until the box reboots automatically. This may take around 2 minutes and you will see the Astro logo again when it's done.

Advance payment can be made via credit/debit card or online banking.

Streaming app entitlement is dependent onthe TV Pack you are subscribed to, with some streaming apps available on Astroas an add-to-bill service. Please visit product.astro.com.my/apps to seeif you are entitled to your favourite streaming app once it is launched!

Yes, a penalty fee of RM200/Mesh WiFi unit will be imposed if the customer fails to return the device(s). The courier company will make two attempts to retrieve the Mesh WiFi unit(s) within a period of 30 days, failing which the penalty would be imposed.

STEP 1
Check the internet connectivity by run the Test Connection.
Refer Run Test Connection.


STEP 2
Verify the average speedtest based on the Test Connection result.
a. Above 10Mbps - Proceed to STEP 5
b. Less then 10 Mbps - Proceed to STEP 3

Notes: Minimum 10 Mbps internet speed from box requires in order to get a stable connection.



STEP 3
Check the connection to the box either using Ethernet (LAN cable) or Wi-Fi.
a. If using Ethernet (LAN cable) - Connect to Live Agent for help.
b. If using Wi-Fi - Proceed to STEP 4



STEP 4
Check location of the decoder and router.
a. If nearby (within 1.5m) - Try connect to box from router using LAN cable.
b. If far (more than 1.5m) / No LAN cable - Proceed STEP 5



STEP 5
Reboot router, modem and decoder.
If issue persist, please try again after 30mins to 1 hour. Connect to live agent if persist after 30 mins to 1 hour.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer  than 15 minutes.

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Black port at D-Link Router and direct to the computer/laptop).    

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.    

3. On the address bar, please go to tplinkwifi.net and to access to below login page. Type the Username and Password, then click "Login".

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your router previously, the password may be  different)

For example, below is the login details of the above router:

Username: admin

Password: TIMECE24

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, choose Basic and then click Wireless tab on the left menu to access to below screen.

6. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

7. You may change the Wireless Network Name (SSID) and the Password to follow your preferences, then click "Save"  for the changes to take  place.

Please reconnect to the new wireless name with the new password once completed.

‍

To allow customers to decide on their WiFi connection arrangement based on their preference upon being advised by the installer on-site.

User to manually connect their devices to different WiFi bands based on their usage and preference.

Refund  can be made when there be a termination of account, over payments and in  cases where payment was wrongly made to another Astro account.

When you have reached the duration (years) needed for the upgrade, we will upgrade you into your new tier and your shiny new rewards will appear in the My Astro app. You are still eligible for all the rewards from previous tiers too.

Your account number will be used to identify/verify you for all After Sales-Services. You may also use your mobile number/ Astro smart card number/ NRIC number or Astro Box number.

You may call Astro's Contact Centre at 03-9543 3838 or wait for an Astro representative to be in contact with you within 2 working days to assist you with your order.

Check out our user guide for a quick and easy way to get started!
 

Download our user guide in English

Download our user guide in Malay

Download our user guide in Chinese

Do you need more information? Watch our Astro Ultra How to videos here.

If your existing Netflix account is linked with your Astro subscription, your Netflix account will resume on the previous method of payment. If you linked a new Netflix account with your Astro subscription, cancelling Astro service will also cancel your Netflix account.

STEP 1  

On your remote, press the HOME button.

STEP 2  

Navigate to SETTINGS  icon and press "OK".

‍

STEP 3    

Navigate to Manage Satellite Frequency and press “OK”.

‍

STEP 4  

Choose to Update Satellite Frequency and press “OK”.

‍

STEP 5    

Choose "Confirm" to continue Satellite Frequency Update and press “OK”.

‍

STEP 6  

Satellite Frequency Update progress screen will be displayed.    

The updates will take approximately 20 minutes.

STEP 7

The status will be displayed once update is complete.    

You may use the 'forgot password' recovery feature on the login page. Just enter the email address/ mobile number you signed up with and we will send you a recovery email.  

The main changes are the revamped look and feel of the user interface on the Smart TV App, which include redesigns to the Astro interface that consists of title rows at the Home Page to feature popular franchises, new live programmes posters and changes to the menu bar for easier navigation.

For more info, please read our dedicated FAQ on this here.

In addition, we have also recently introduced a new look to the Title Information Page and the ability to disable the Profile Selection Screen. For more information, please click here.

Customers with a Netflix Premium account are allowed to watch on up to 4 supported devices in 4K UHD and Netflix Spatial Audio. In addition, Netflix Premium subscribers are also allowed to download shows to watch offline on 6 devices at a time.

Astro offers 3 different after-sales service that is made available to the customers:

(1)  Express (RM75)

(2)  Same Day (RM70) 

(3)  Regular (RM65) 

‍

***Price is inclusive of 6% Service Tax.