Upon successful subscription, you will be able to view your chosen HD channels within 3 hours by keying in the channel numbers into your remote control. Please note that subscription through Channel 200 will take effect within 24 hours.

STEP 1
Please wait while your Astro box initializes.



STEP 2
Select your preferred language.



STEP 3
Navigate to Next and press "OK".



STEP 4
Select Auto as the Video Resolution.



STEP 5
Navigate to Next and press "OK".



STEP 6
Navigate to Confirm and press "OK" to confirm your selection if you are able to read the texts on screen properly.
Otherwise, navigate to Cancel to revert to the previous settings.



STEP 7
Select Satellite as the box operating mode.



STEP 8
Navigate to Next and press "OK".



STEP 9
Select your preferred connection.
For connection via Wi-Fi, proceed to STEP 10.
For connection via LAN Cable, proceed to STEP 16 once you are connected.



STEP 10
Please wait while your Astro box searches for available Wi-Fi networks.



STEP 11
Navigate to your preferred Wi-Fi network and press "OK".



STEP 12
Please enter the password to connect to the Wi-Fi network.



STEP 13
Navigate to Done to continue.



STEP 14
Please wait while your Astro box connects to the internet.



STEP 15
Navigate to Yes to allow your Astro box to connect to this network automatically.
Otherwise, navigate to No.
Proceed to STEP 17 for the next step.



STEP 16
Navigate to Next and press "OK". 



STEP 17
Navigate to Universal.



STEP 18
Navigate to Next and press "OK".



STEP 19
Select 01 M3B VL - 10732 as the Entry Point.



STEP 20
Navigate to Next and press "OK".



STEP 21
Please wait until the signal reading is updated.
Navigate to Finish and press "OK" to complete the settings.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Video Resolution and press “OK”.

STEP 4

Navigate to your preferred selection and press “OK”.

Recommended to select Auto.

STEP 5

Navigate to Save and press "OK" to confirm your selection if able to read the text properly.

Otherwise, navigate to Cancel to revert to previous settings.

STEP 1

Switch off the power for your box and  make sure that the adapter's power light is off.

STEP 2

Locate the Smartcard at the front or right side and gently pull it out.

Make sure that the adapter's power light is off.

STEP 3

Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5

Switch on the power for your box and make  sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form and attach a picture of your smart card number for assistance.

Yes. You are entitled to separate Netflix accounts for each main Astro subscription e.g. If you have subscribed to Entertainment Plus, Platinum Pack, etc separately. Therefore, if you have more than one main Astro subscription with Netflix, you may choose to create multiple email addresses to activate each respective Netflix subscription. Please follow the steps provided to you via email/SMS in order to activate your Netflix subscriptions on the website.

You can proceed with below troubleshooting if the weather is good. Ortherwise, you may try again later.

STEP 1
On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.


STEP 2
Navigate to SETTINGS and press “OK”.


STEP 3
Navigate to STB DIAGNOSTICS and press “OK”.


STEP 4
Refer to the signal strength % shown on the top left of your screen.
If it is 65% or higher, please go to WhatsApp to receive further help.
If it is below 65%, please go to STEP 5.


STEP 5
Switch off the power for your box and make sure that the adapter’s power light is off.


STEP 6
Unscrew the satellite cable from the box and pull it out.


STEP 7
Plug the satellite cable back into the box and screw it back securely.


STEP 8
Switch on the power for your box and make sure that the adapter’s power light is on.
Please wait for 5 minutes.


STEP 9
Turn on your box. You should no longer be experiencing this issue.
If issue persist, please attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized Dish
 If issue persist under a centralised satellite dish, please refer to your respective Building Management before contacting our agents.

The "coming soon" label on some streamingapps on your TV and the "Apps" page of Astro's website allows our customers tostay on top of new launches as they happen! Stay tuned for these upcomingstreaming apps so you can access even more content that you love from acrossthe world.

Payment for Astro services will not increase. However, the Service Tax applicable will be increased from 6% to 8% and this will result in an increase in the total amount payable.

If you did not receive the recovery email or verification code, please make sure that:

1. You are inserting the correct email or mobile number you used to register for your Astro ID.
2. Check your junk mailbox or spam folder.  

To find out which email or phone number you have used to register your Astro ID, you may submit a feedback form. Kindly select feedback type "I have an enquiry/issue with Apps" choose "Astro GO" 
 

We will get in touch with you within 48 hours to solve your enquirie

Please submit your issue here or you can WhatsApp us at 03-9543 3838.

STEP 1
In the Kids Profile, press the Home button on your remote and the home menu will be displayed.



STEP 2
Navigate to Profile.



STEP 3
The Profile Selection Screen will be displayed.



STEP 4
Choose an Adult Profile.



STEP 5
Switching from a Kids to an Adult Profile will require you to enter a 4-digit PIN.
Please enter your PIN to proceed. If you have not set up your PIN, the default code is 0000.



STEP 6
After entering the PIN, you will be able to enter the Adult Profile.


 

For TV packs only, 24-months contract commitment period. However, if in addition to the TV packs, if you would like to also sign-up for Broadband, the contract commitment will be 24 months as well. If you're an existing customer, your existing remaining contract duration (if any) will not be carried over to the new contract except for existing Disney+ Hotstar (3 Months Pack) and Multiroom subscription contract durations which will be carried over upon the migration to new packs.

Note: If you are subscribing to a bundle pack which includes Netflix or Disney+ Hotstar for the first time, you are required to maintain the respective app as part of your bundle selection for a minimum of 12 months, otherwise a cancellation fee will apply.

Once you have received the eKYC link via SMS/email/astro.com.my, you can proceed to follow the instructions on the screen. You can check out the step-by-step image below for more info.

For MyKad/MyPR/MyTentera :

For Passport :

When Band Steering is enabled, only one SSID network name with one password is available. Example:

i.SSID: SSID, Password: 12345678

For Ultra/Ulti Plug & Play Box installation, it is recommended that you attempt to self-install by following the installation guide here, but there is an option to request for an installer to install the box at your premise. However, there will be a separate fee for this service request.

For customers that would like to subscribe to Multiroom with a box installation,

(i) customers on the old packages (example Family Pack, Starter Pack, Value Pack, Super Pack or Super Pack Plus) will have to subscribe to our new packages first by sending "Switch" to 03-9543 3838 via WhatsApp;

(ii) customers on the new Astro packages can subscribe by visiting product.astro.com.my/multiroom or WhatsApp "Hi" to 03-9543 3838.

Some of our payment partners require payees to scan the barcode on the statement to make payment. Always bring your Astro bill statement when making payment over the counter.

Option 1

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.    

2. Ensure the fiber cable from your wall socket and modem is securely connected.

Notes: You might be connected to LAN 1 if backbone is Maxis

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

4. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 2/ Option 3/ Option 5/ Option 6

1. Please turn off all devices (Modem and Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would  impact its performance.

2. Ensure the fiber cable from your wall socket and modem is securely connected.

3. Ensure both cables on the Modem (LAN Port 2) and Router (WAN Port - Red port) are properly connected.

Notes: You might be connected to LAN 1  if backbone is Maxis

Router connection

4. Please make sure the LAN cable is connected properly from router (Port 1-4 - Yellow port) to PC/Laptop.

5. Please make sure both cables on Router (Any Yellow port) and Astro Decoder (Network Port behind decoder) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

7. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.

Call our contact centre 03-9543 3838 or visit us at astro.com.my.

A security question will be asked when making payments with credit cards over the phone. All other payment channels will not require any form of verification.

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please ensure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Intermittent internet connection using Wi-Fi

1. Router Positioning
   Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
   
    i) High vs. Low
   Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   
   ii) Concrete & Metals
   Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   
   iii) Distance to Router
   The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
   
   Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.
   
    

2. Wireless Interference & Noise
   You've probably never noticed but there are wireless signals all around you wherever you go and they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.
   
   Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:
   i) Microwaves
   ii) Bluetooth Devices
   iii) Cordless Phone
    

3.  Surrounding Wi-Fi signals
   A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel  overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many  routers within close proximity. Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

4. Usage
   More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the blue port in Cisco Router and direct to computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

‍

‍

4. Type the Username and Password as below. Then click "OK". (These are the defaults, if you have done previous configuration on your router the password may be different).

Username: admin

Password: admin (or time123)

5. Click "OK" when a Warning prompt that says,” Using this advanced utility to change your router settings could disable your network” appears. Below display will appears.

6. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

7. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

8. Click Wireless Security to view the security settings of your wireless network. Take note of the Security Mode and the Passphrase.

For the example below, the Security Mode used is WPA2/WPA Mixed Mode.

The Wireless name is called Network Name (SSID) and the Passphrase is your wireless password.

‍

9. Now that you have the Wireless name and Password, you are ready to connect your wireless computers and devices to the network.

10. You may change the Network Name (SSID) and the Passphrase to follow your preferences and please ensure save the changes made. Please reconnect to the new wireless name with the new password once completed.

‍

Yes. You can make payment using your credit card via My Astro Portal:

- For One-time payment: All Master/Visa 3D secured debit/credit cards for one-time payment issued by banks in Malaysia

- For Auto-Debit: All Master/Visa/AMEX debit/credit cards issued by banks in Malaysia

To access these streaming apps, you would need to upgrade to the Ultra or Ulti Box by visiting product.astro.com.my/box. Alternatively, you may also reachus via WhatsApp by typing "Hi

Your current additional RM20 rebate will be removed. However, you will still get to enjoy the standard bundle rebate accordingly.  

STEP 1    

On your remote, press the ... button and the Channel Guide page will be displayed on your screen.

STEP 2    

Select the channel you would like to unlock and press "OK".

STEP 3    

Select "Unlock Channel" and press "OK".

STEP 4    

Enter the PIN to unblock the channel.

STEP 5    

You are successfully unlocked the channel when this screen appears.

For any technical issues, you may visit Astro's Help & Support page or contact Astro via WhatsApp at 03-9543 3838 by typing PNP.

The WiFi SSID and password of the Mesh unit will be automatically synchronized to the WiFi router. Hence, there is no need to configure the WiFi parameters.

*WiFi SSID (Service Set Identifier) is the name of your wireless network, also known as Network ID. It is viewable to anyone with a wireless device within reachable distance of your network.

Real-time payments are posted almost instantaneously. However, daily system maintenance occurs between 12AM to 3AM - any payment made during this period will be delayed until system maintenance is complete.

You do not need to request for a reconnection as our system will detect your payment and process it immediately, provided you paid via a real-time payment channel.

Click here for a full list of our payment channels.

You may check your bills and outstanding via:

• Channel 200 from your Astro Box.
• Astro Self Self-Serve Portal or MyAstro App via this link.
• WhatsApp "Payment" to 03 9543 3838 and follow the steps provided.

1. Please standby computer/laptop to access to the internet and connection must be via (cable) [Connect the LAN (cable) to the yellow port in Maxis Router and direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 or www.tplinkwifi.net and below page will appear.

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your router previously, the password may be different

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.
 

5. From the top menu, choose Basic and then click Wireless tab on the left menu to access to below screen.

6. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

7. You may change the Wireless Network Name (SSID) and the Password to follow your preferences, then click "Save"  for the changes to take place.

Please reconnect to the new wireless name with the new password once completed.

Although anyone can create an Astro ID, only the Astro account owner is allowed to link their account to the Astro ID. Otherwise, you will need permission from the account's owner in order to complete the linking.

You can track your ticket status by contacting us via WhatsApp or call us at 03-9543 3838.

Customers with a Movies subscription via Movies, Premium 1, Premium 3 or Platinum Packs will be able to access Disney+ Hotstar on the Ultra Box and Ulti Box. Alternatively, customers can add on the 3-months Disney+ Hotstar pass for only RM54.90. Subscribe to Disney+ Hotstar via astro.com.my/Disney.

Netflix is a streaming entertainment service that offers a wide variety of award-winning TV programmes, films, anime, documentaries and more - on thousands of internet-connected devices. There's always something new to discover, and more TV shows and movies are added every month. The more you watch, the better Netflix gets at recommending TV shows and movies you'll love.

Astro customers with an internet-connected Ultra Box or Ulti Box can access the Netflix app and watch Netflix content via their Astro Box. For more information about Netflix, visit the Netflix website.

If you add on the Mesh WiFi during your initial order of Astro Fibre, there is no additional installation fee. If you order the Mesh WiFi as an add-on at a later time, you will have to pay RM49 per installer visit. However, if you choose to have the Mesh WiFi delivered via courier in order to self-install your Mesh WiFi, there will be no installation or delivery fee charged.

Astro Multiroom is a 2nd Astro subscription that mirrors all the channels on your primary Astro at a discounted monthly fee. You can now enjoy Astro on different TVs in different rooms.

STEP 1    

On your remote, press the Home button and the home menu will  be displayed on top of your screen.

STEP 2

Navigate to Guide.

STEP 3    

Select the channel you would like to lock and press "OK".

STEP 4   

Select "Lock Channel" and press "OK".

STEP 5    

You channel is successfully locked when this screen appears.

STEP 6

Your selected channel will  have a lock tagging after being locked.

STEP 1
Switch off the power of your box and make sure that the adapter’s power light is off.


STEP 2
Unplug the HDMI cable from your TV and plug it back in securely to other available HDMI port.


STEP 3
Switch on the power for your box and make  sure that the adapter’s power light is on.
Please wait for 5 minutes.


STEP 4
Turn on your box. Do select the correct TV input.
You should no longer be experiencing this problem. 
​

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which could  cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.