STEP 1

Switch OFF the power of your Ultra / Ulti box and make sure that the adapter's power light is off.
 

STEP 2

Switch ON the power of your Ultra / Ulti  box and make sure that the adapter's power light is on.
 

STEP 3

On your remote control, press the Home or Standby button repeatedly until the Startup Options appear on TV.



STEP 4
Press "987" to proceed.
Advanced Startup Options will be displayed.



STEP 5
Press "1" to initiate a reset setting.



STEP 6
Press "OK" to continue.



STEP 7
After the factory setting is restored, TV will turn blank.
Please wait until the box completes initiate setup.



STEP 8
Once completed, the following screen will appear on your TV.
Refer to Installation Setup guide to complete the setup.

Click here to follow New Installation Settings guide for Satellite
Click here to follow New Installation Settings guide for Plug and Play

STEP 1  

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2    

Navigate to SETTINGS and press “OK”.

STEP 3  

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4    

Refer to the signal strength % shown on the top left of your screen.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the blue port in Cisco Router and direct to computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.

3. On the address bar, please go to http://192.168.1.1 and below page will appear.

‍

‍

4. Type the Username and Password as below. Then click "OK". (These are the defaults, if you have done previous configuration on your router the password may be different).

Username: admin

Password: admin (or time123)

5. Click "OK" when a Warning prompt that says,” Using this advanced utility to change your router settings could disable your network” appears. Below display will appears.

6. On the setup page, click the Wireless tab then click on the Basic Wireless Settings sub-tab.

7. On the Configuration View section, click the Manual radio button. Choosing the Manual setup will allow you to adjust your wireless channel according to your preference.

8. Click Wireless Security to view the security settings of your wireless network. Take note of the Security Mode and the Passphrase.

For the example below, the Security Mode used is WPA2/WPA Mixed Mode.

The Wireless name is called Network Name (SSID) and the Passphrase is your wireless password.

‍

9. Now that you have the Wireless name and Password, you are ready to connect your wireless computers and devices to the network.

10. You may change the Network Name (SSID) and the Passphrase to follow your preferences and please ensure save the changes made. Please reconnect to the new wireless name with the new password once completed.

‍

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Audio Delay and press "OK".

STEP 4

Navigate to your preferred selection and press “OK”.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your Ultra Box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form with the error details and provide sim card number for assistance.

From Channels 480 (Astro First):

1. ‍Go to channel 480
2. Search for the Movie title or Series and press “OK” button from Astro remote control;
3. Choose how to purchase via WhatsApp or SMS.
4. Enter the Pin Code

Purchase via Whatsapp

1. ‍Go to channel 480‍
2. Whatsapp the “movie code” to 03-9543 3838 
3. Enter your “smart card number” (this is available on the top right corner of your tv screen)‍
4. Type “1” to confirm
5. The reply will direct you to the entitlement channel accordingly

Purchase via SMS

1. ‍Go to channel 480‍
2. SMS the “movie code” to 32999 ‍
3. The SMS confirmation reply will direct you to the entitlement channel accordingly

*SMS service is available for Maxis, Celcom, Digi and U Mobile only.

‍

From Beyond PVR On Demand interface:

1. Press the “Home” button on the Astro remote control
2. Select “On Demand” and press the “OK” button from the Astro remote control
3. Scroll to “Store” and search for the Movies/series
4. Select “Buy” and enter Pin Code. 

‍

From Ultra/Ulti On Demand interface:

1. ‍Press the “Home” button on the Astro remote control 
2. Scroll to the Store tab
3. Scroll to “Astro First: New Releases” or “Astro First: Blockbusters” and search for the Movies
4. Select “Rent” and enter Pin Code

‍

From Astro Go app (purchases only applicable for Android devices): 

1. ‍Download the Astro Go app from the Google Play store.
2. Create an ID and link your account / proceed to log in if you have linked your account
3. Scroll to “Store” and search for “Astro First: New Releases” or “Astro First: Blockbusters”
4. Select “Rent” and enter Pin Code

*The default pin code is 0000 if you have not pre-set it.

1. Via Television

    a) Ultra Box

• Press the “Home” button and scroll to “Settings” > “Wi-Fi/Ethernet” > “New Wi-Fi Connection”

• Allow the Ultra Box to scan the Wi-Fi networks available and subsequently choose your home Wi-Fi network > Enter your Wi-Fi password

• Once you are connected, your Home screen will now show “tabs” where you can now enjoy Video On Demand

‍

o  “Catch-up” missed episodes from ongoing programmes

o  Binge-watch full seasons from “Boxsets”

o  Choose the your favourites from “Movies”, “Kids” and more

‍

2. Mobile/Portable devices

(a)  Just head to the Google Play Store, Huawei App Gallery or Apple App Store here, search for “Astro GO” and download Astro GO on iOS and Android devices. Login to watch on demand and other ASTRO channels based on your subscription.

STEP 1
Please wait while your Astro box initializes.



STEP 2
Select your preferred language.



STEP 3
Navigate to Next and press "OK".



STEP 4
Select Auto as the Video Resolution.



STEP 5
Navigate to Next and press "OK".



STEP 6
Navigate to Confirm and press "OK" to confirm your selection if you are able to read the texts on screen properly.
Otherwise, navigate to Cancel to revert to the previous settings.



STEP 7
Select Satellite as the box operating mode.



STEP 8
Navigate to Next and press "OK".



STEP 9
Select your preferred connection.
For connection via Wi-Fi, proceed to STEP 10.
For connection via LAN Cable, proceed to STEP 16 once you are connected.



STEP 10
Please wait while your Astro box searches for available Wi-Fi networks.



STEP 11
Navigate to your preferred Wi-Fi network and press "OK".



STEP 12
Please enter the password to connect to the Wi-Fi network.



STEP 13
Navigate to Done to continue.



STEP 14
Please wait while your Astro box connects to the internet.



STEP 15
Navigate to Yes to allow your Astro box to connect to this network automatically.
Otherwise, navigate to No.
Proceed to STEP 17 for the next step.



STEP 16
Navigate to Next and press "OK". 



STEP 17
Navigate to Universal.



STEP 18
Navigate to Next and press "OK".



STEP 19
Select 01 M3B VL - 10732 as the Entry Point.



STEP 20
Navigate to Next and press "OK".



STEP 21
Please wait until the signal reading is updated.
Navigate to Finish and press "OK" to complete the settings.

New and existing Astro customers will enjoy rebates up to RM39/month for 24 months when they subscribe to selected Astro Fibre TV bundles and a FREE speed upgrade for all customers who subscribe within the promotion period.
 

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

Yes, you may cancel your Astro Fibre order before service activation, however, kindly note that there is a cancellation charge of RM212 (inclusive of SST) for any service cancellation done 48 hrs before scheduled appointment.

Having trouble with  your phone line ?

You may proceed to contact below dedicated service provider directly

1 800 1818 18

1. Please use a LAN ethernet cable and connect your computer/ laptop to the back of the Maxis Router.

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox, etc.

3. On the address bar, please go to http://192.168.1.254 and the page below will appear.

    The default login of the router as below. If you have done a configuration on your router and changed your password previously, please use the password you have previously set.
 

    Username: administrator

    Password: Router S/N (Available on the sticker at the back of the router)

4. Once you have successfully login, the router's web-based setup page will appear.

5. From the left menu, select WIRELESS to access the screen below.

6. You may change the Channel selection by scrolling down to the Advanced Setup.

7. To change the channel on 2.4 GHz and 5 GHz, click the drop-down arrow for Channel, then select your desired channel.

Then, click "Apply" for the changes to take  place.

8. A warning box will popup, click "OK" for the changes to take place.

9. Please wait until the connection reestablish.

Please check your internet speed and connection status via internet connection test. If your internet is working fine and the issue persists, proceed to submit report via WhatsApp or Feedback Form.

Astro & Broadband offers Astro content with Astro Fibre, Maxis Fibre Broadband and Allo City Broadband for customers to enjoy the best entertainment through Astro while staying connected with high-speed internet.

With the current Astro & Broadband plans, customers will enjoy substantial savings by choosing their desired broadband speed from 30Mbps - 800Mbps to accompany their Astro packages.

Please switch your current subscriptions to our new Astro packs to subscribe to Multiroom (Smart TV). To sign up, WhatsApp “SWITCH” to 03-9543 3838 and an agent will assist you. 

Find out more of our new packs at https://product.astro.com.my/tv

Astro Fibre installation will come with 1 unit of TM fibre modem and 1 WiFi router with 24 months warranty period.

While warranty period for Mesh WiFi will be treated as one-to-one swap for faulty Mesh units at any point of time during your service tenure with active Mesh subscription.

No, the Ulti Box does not support 4K UHD content. If you would like to watch Astro's 4K UHD content, please sign up for an Ultra box at Astro Ultra Box and Ulti Box | Astro.

All Astro customers with Disney+ Hotstar bundle/Add-on will be moved to the Disney+ Hotstar Premium Plan, with no changes to their current subscription pricing starting 24 April 2024. The new Disney+ Hotstar Premium Plan includes 3 concurrent streams, 10 maximum device logins, maximum video quality up to 4K Ultra HD (compatible devices required), and streaming on phone, tablet, laptop and TV.

If you have questions about your Disney+ Hotstar plan, please contact Astro Customer Contact Centre at 03 9543 3838. Alternatively, please WhatsApp Astro at 03 9543 3838 and type DH Help for further assistance. 

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/ laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/ laptop].
2. You may open any web browser such as  Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)

Username: admin
Password: admin (or time123)
 

5. The router's web-based setup page should now appear. Please follow below steps for the  configuration.

i. On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab.

ii. Please ensure Wireless RF Mode is Enabled.

iii. Click the drop-down arrow for Channel, then select your desired channel.

Choose between 1 until 11 (Suggested 1,6,11).

iv. Click Submit. Router will auto reboot and connection re-establish after few minutes.

You may contact Astro's Contact Centre (03 - 9543 1543) to process the cancellation.

The Mesh WiFi device(s) needs to be returned upon service termination via an arranged pick-up by our installers.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer than 15 minutes.        

‍

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Black port at D-Link Router and direct to the computer/laptop).

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.    

3. On the address bar, please go to http://dlinkrouter.local./ and below page will appear. (These are the defaults and if you have done a configuration on your router previously, the password may be different).          

Username: admin          

Password: (Leave the field blank)

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, click Settings and then choose Wireless.

6. Below screen will appear to configure the wireless setting. Since this is a dual band router, you will have 2 Wi-Fi Names (SSID) i.e. 2.4GHz and 5GHz.

You may connect to any of the SSID, preferably with a stronger signal available.

7. You may change the Wi-Fi Name (SSID) and the Password to follow your preferences, and then click "Save" for the changes to take  place.

Please reconnect to the new wireless name with the new password once completed.

By changing from a higher contract duration e.g., 24-months commitment period to lower contract duration e.g., 12-months, a proration of the cancellation fee will be applicable whereby you will be charged per contract's month balance against the maximum cancellation fee agreed upon during sign up for the offer.

A proration of the cancellation fee will be applicable whereby you will be charged per contract's month balance against the maximum cancellation fee agreed upon during sign up for the offer.

You will start a new contract with 12-months commitment and receive the corresponding discount for that duration.

Check out how a cancellation fee is calculated with examples via this link:

No, the Mesh WiFi add-on with Astro Fibre is only available as a subscription service and will not be tied to any device contract.

STEP 1

Switch off the power for your box and make sure that the adapter's power light is off.

STEP 2

Locate the SIM card at the left side and gently pull it out.

STEP 3

Wipe the SIM card's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing down and reinsert it all the way in.

STEP 5

Switch on the power for your box and make sure that the adapter's power light is on.

Please wait for 5 minutes.

STEP 6

Turn on your Ultra Box. You should no longer be experiencing this problem.

If issue persist, please submit the issue in our Feedback Form with the error details and provide sim card number for assistance.

Astro customers can make payments via Auto-debit, WhatsApp,Astro Quick Pay and other authorised payment channels withoutsurcharge for the easiest and fastest way to pay their Astro bills.

‍Bill payments at selected petrolstations, convenience stores, retail/mobile shops, kiosks, and e-Wallets, may incur a surcharge of up to RM0.50 per transaction by the appointed collection agencies of RMS (Razer), ATX, MobilityOne and e-Pay.

The surcharge is imposed by third-party payment collection partners for services rendered.‍

You can refer to all our payment options below. Those marked with ‘*’ will be subject to a surcharge by appointed collection agencies.

‍

A. HASSLE-FREE METHODS

Auto-Debit:​
Click here for step-by-stepinstructions on how to activate auto-debit payment via My Astro Portal.‍


WhatsApp:

1. Save Astro’s WhatsApp number 03-9543 3838 into your contacts and send “Hi”to us via WhatsApp.
2. Follow the instructions in the menu to proceed with your payments.

JomPAY:​
Look for the JomPAY logo on your latest bill, log into your preferred online banking platform, and submit your payment details.
• Biller Code: 9639 (unique to Astro only)
• Ref-1: <10-digit Astro account number> (E.g. 08XXXXXXXX)


B. ASTRO SELF-SERVICE METHODS​

Astro Quick Pay​:

1. Visit pay.astro.com.my.
2. Just enter your 10-digit Astro Account Number and proceed with theinstructions that follow.

My Astro Portal​:

1. Login to My Astro Portal to conveniently make your payment online.
2. Select ‘PAY BILL’ and proceed with the instructions that follow.
3. You can also use this portal to check your billing and payment history.

Channel 200​:

1. Tune into CH200.
2. Select 'My Account'.
3. Click on 'Make Payment' and follow the instructions displayed on the screen.
4. SMS the code shown on your TV to 33777.
5. Wait for the SMS reply with an attached link to proceed with your payment.

My Astro App​:

1. Download My Astro app (available for FREE on both Google Play & Apple App Store).
2. Register/Login/Link account and provide a valid email address and mobile number.
3. Select 'My Account' on the menu bar to view your outstanding balance and click on 'Let’s Pay' to make your bill payments.
4. You will receive a push notification in your message inbox verifying that your payment has been made, upon successful payment.

C.BANKS​

Maybank:

• ATM
• Online banking

‍Visit maybank2u.com.my for more information.


Public Bank:

• ATM
• Cash Deposit Machine & Cheque Deposit
• Online banking

‍Visit pbebank.com for moreinformation.


Bank Simpanan Nasional:

• ATM
• Cash Deposit Machine
• Online banking
• SMS banking
• BSN Ejen Bank Berdaftar (EBB)
• Over-the-counter payments

‍Visit mybsn.com.my for more information.


Agrobank:

• ATM
• Online banking
• Over-the-counter payments

‍Visit agrobank.com.my for more information.
‍

D. e-WALLETS

A‍TX*
Boost, GoPayz, KelantanPay, Zcity (GEM REWARD), SabahPay, Tapay, GoPay,MerchantTradeMoney, ToneGroup, Elinking, Mpay, Mcash, and other various smaller wallets.

e-Pay*
Touch n Go (TnG), Grab Pay, Shopee, BigPay, True Money

‍E. OTHER METHODS​‍

‍Associated Retailers​:

RMS (Razer/ MOL)*
7-Eleven, 99 Speedmart, Caring Pharmacy

ATX*
RedONE Shop, Mobile Money, Runcit Hero (telecommunication shops), Parcel Hub (courier shops), Kiosk, DHL

Mobility One*
Kedai D’mart, Happy Mart, Pasaraya Sakan, PusatKomuniti Desa (PKD), Aeon Big and various sundry shops‍

e-Pay*
Petrol stations (Petronas, Shell, BHP, Caltex, Petron), KK Mart, Mydin, MyNews, SenHeng, Hai-O, Giant, TF ValueMart, Billion, Big Pharmacy

Yes, your charges during the deferment days will be pro-rated and reflected in your next bill. Please note that due to the recent requested change in your Astro account, the expiry date for your Disney+ Hotstar (3-months pass) subscription has been deferred to xxx (date) to consolidate the final monthly subscription pricing.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Master PIN and press “OK”.

STEP 4

Please enter your PIN (Default PIN is 0000).

STEP 5

Please enter your new PIN.

STEP 6‍

Please re-enter your new PIN to confirm.

STEP 7

Your PIN successfully changed when this  screen appears.

Astro GO is a free streaming companion app for all Astro customers to enjoy their favourite shows and channels on their smartphones, tablets, and computers - anytime, anywhere in Malaysia. Astro customers with an active Pay-TV subscription can link their accounts to watch corresponding on demand and TV channels available on Astro GO as part of their subscription.

Please ensure to put your box on standby mode to refresh the signal.

a. Using IVR

1. Dial 03-95433838 and select you preferred language.
2. Select Account Related.
3. Select Technical Assistance.
4. Select Refresh Smartcard.

b. Using MyAstro web

STEP 1
Go to https://myastro.astro.com.my/ in your web browser.



STEP 2
Key-in your Email / Mobile number and password. Then, press LOG IN.



STEP 3
Click on TV pack.



STEP 4
Choose Main Room for the Primary Box; else choose Multiroom (If any).



STEP 5
Click on "Refresh" to refresh signal on your box. 

For Main Box


For Multiroom


STEP 6
After tap the Refresh, below notification will be displayed as below.

For Main Box


For Multiroom


c. Using MyAstro App

STEP 1
Open myAstro App and click "Login".



STEP 2
Key-in your Email / Mobile number and password. Then, press "LOG IN".



STEP 3
Go to "Account".



STEP 4
Scroll down to "TV pack" and click on it.



STEP 5
Choose Main Room for the Main Box; else choose Multiroom (If any).



STEP 6
Tap on "Refresh" to refresh signal on your box. ​

For Main Box


For Multiroom


STEP 7
After tap the Refresh, below notification will be displayed as below.

For Main Room


For Multiroom

Of course not! It is a value-added service introduced for your convenience.

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2    

Navigate to Settings.

STEP 3    

Navigate to STB Diagnostics and press "OK".

STEP 4    

Select General Diagnostics and press "OK".

STEP 5  

Details information of General Diagnostics screen will be displayed.

STEP 6    

Press down arrow on your remote to get more information.

For My Astro App Users 
Go to the "Account' tab and scroll to "Personal Info' section. Click "Name & contact info' to view and update your personal contact information.

For Ultra and/or Ulti Users 

1. Launch the My Astro app on your Home screen and you will land on your My Astro account dashboard. Then, press the yellow button on your Astro remote control to visit your "Account details".
2. Press the down button to view the "Personal info".
3. Press the left button and focus on the edit icon for the contact details, press on "OK" to change your contact details.

1. Please connect your computer or laptop to your Astro Fibre router using WiFi or LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).
2. Once connected, open any web browser  such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.    
3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router  login is as per below.          

Username: user
Password: user

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click WLAN to configure the WiFi parameters.

6. To change the channel on 2.4G, click the drop-down arrow for Channel, then select your desired channel.

7. Then, click "Save & Apply" for the changes to take place.

8. You may make the same changes for 5G by click the drop-down arrow for Channel, then select your desired channel.

9. Then, click "Save & Apply" for the changes to take place.

Astro GO is a companion app that is complimentary for all Astro subscribers and allows up to 2 users to stream at the same time. 200 hours of cloud recording* come complimentary with your Pay TV subscription. 

Astro GO+ is an add-on service that enables up to 4 users to stream Astro GO and/or Multiroom Smart TV** at the same time. The amount of cloud recording storage will also be increased to 1500 hours. 

 *Cloud recording hours are shared across your Astro Box, Astro GO and Multiroom Smart TV 

** Provided that you have a Multiroom Smart TV subscription

1. Ensure power cable  is connected tightly.

2. Try to use another power socket /  power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue  persists, submit your feedback form for further assistance.

The supported app platforms are iOS (requires iOS 13.0 or later), and Android (requires Android 8.1 or later), and all Harmony OS.

The supported web browser are Google Chrome, Safari, Mozilla Firefox, Microsoft Edge, Internet Explorer, Opera and other web browser.

Unfortunately, this means that you are using a TV model that does not support 4K UHD resolution (Sony BRAVIA 4K GB, Sony BRAVIA 4K UR or Sony BRAVIA VH). Not to worry, we are working with the Sony team to ensure you will be able to enjoy these 4K UHD channels soon. We will keep you posted once these channels are available to you!

Depending on your service, it is mandatory to return some devices as per our T&Cs, whilst other devices should be disposed of and recycled at collection centres registered under the Department of Environment. To find out what you should do with your devices after service termination, please click here.

Mesh WiFi devices are available as an add-on subscription from RM10/month across all Astro Fibre speeds. You may subscribe to a maximum of 5 units of Mesh WiFi per Astro Fibre subscription. 

You can contact Astro's Contact Centre (03 - 9543 1543) to subscribe to the Mesh WiFi.

If you choose to self-install the Plug& Play Box, then no installation fee will be charged. However, there will be an activation fee (please refer to the table below)

If you choose to have an installer to install the Plug & Play Box, then an installation fee will also apply.

STEP 1

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2

Navigate to Settings.

STEP 3

Navigate to Standby Mode and press "OK".

STEP 4

Navigate to your preferred selection and press "OK".

STEP 5

Navigate to Save and press "OK" to confirm your selection.

STEP 1

On your remote, press the “HOME” button and the home menu will  be displayed at the bottom of your screen.

STEP 2

Navigate to SETTINGS and press “OK”.

STEP 3

Navigate to STB  DIAGNOSTICS and press “OK”.

‍

STEP 4

Select the “Network” tab in the STB Diagnostics page.

Please ensure the Tunes service multicast  status is Multicast Up.

If the status is Multicast is Not Available, please reboot your box and router before verifying this status.

If issue persists, please submit the issue in our Feedback Form and attach a picture of your Network tab of the STB Diagnostics for assistance.

To be eligible, you'll need to be an Active Astro Pay TV customer with a valid Astro ID.

An Active Astro customer refers to a subscriber of the Astro Service, whose account is current and active with no outstanding payments due and who has not breached the Astro subscription agreement nor given any instructions to terminate and/or suspend his/her subscription to the Astro Service.

Each account you hold is entitled to one (1) tier status based on the longest active smartcard.

We would recommend the following browsers for a smooth verification process:

• Google Chrome

• Microsoft Edge

• Mozilla Firefox

• Safari