There is no contract for this subscription.

You can proceed with below BTS if the weather is good. Otherwise, you may try again later.

‍

STEP 1

On your remote, press the HOME button and the home menu will be  displayed on top of your screen.

STEP 2

Navigate to SETTINGS.

STEP 3

Navigate to Satellite Settings and press “OK”.

STEP 4

Navigate to Diagnostics and press “OK”.

STEP 5

Refer to the signal strength on your screen.

If it is 65 or higher, please take the screenshot and submit your feedback form.

If it is below 65, please go to Step 6.

STEP 6

Switch off the power for your box and  make sure that the adapter’s power light is off.

STEP 7

Unscrew the satellite cable from the box  and pull it out.

STEP 8

Plug the satellite cable back into the  box and screw it back securely.

STEP 9

Switch on the power for your box and make sure that the adapter’s power light is on. Please wait for 5 minutes.

STEP 10

Turn on your box. You should no longer be experiencing this issue.

If issue persist, please submit the issue on our Feedback Form with error details and attach a picture of your General tab of the STB Diagnostics for assistance.

Centralized  Dish

If issue persist under a centralized satellite dish, please refer to your respective Building Management before contacting our agents.

STEP 1
Check the Audio settings on your box and set to Auto.
Refer guide to change Digital Audio Settings.

STEP 2
If issue persist, check if there is any 3rd party device (sound system/hdmi splitter) connected between box and TV.

STEP 3
If using 3rd party devices, bypass/remove 3rd party device and make sure HDMI cable connected directly from box to TV.

STEP 4
If issue persist, connect to Live Agent via WhatsApp for help.

Visit our page to find out about our new packs.

STEP 1    

On your remote, press the HOME button and the home menu will be displayed on top of your screen.

STEP 2    

Navigate to Guide.

STEP 3  

Select the channel you would  like to add to favourite list and press "OK".

STEP 4  

Select "Add to Favourites" and press "OK".

STEP 5

You are successfully added the channel to favourite list when this screen appears.

STEP 6

Your selected channel will have a heart tagging after added as favourite.

The Liga Malaysia will be available for all Astro customers starting 3 May 2024 as part of your Astro subscription at no additional cost until further notice.
 

Not all shows/channels will be available on the Plug & Play Box as this depends on contractual rights with specific guidelines on the entitlement of these shows/channels and what you have as a part of your subscription.

• Customers subscribing to Plug & Play Box with or without Astro Broadband will not have access to 1 (one) Channel - NHK World

Please be assured that we are continuously working hard to make more content available on the Plug & Play Box.

If you prefer to have all these channels, we recommend that you choose the Satellite dish option for the Ultra or Ulti Box.

Unavailable channels are as below:

The new packs and access to Netflix on the Ultra Box and Ulti Box is available for Astro IPTV customers.

You may retain your watch history and settings of your existing Netflix account by using the same email of your Netflix account during the linking of your Netflix account with Astro.

All Astro customers and non-customers who have an Astro ID will no longer be able to log in to our digital platforms using their usernames. Users will experience this change if they currently do not use an email address or mobile number to login, for example: johndoe2023.

STEP 1    

Press "HOME" button on your remote control.

STEP 2    

Navigate to Settings and press "OK".

STEP 3    

Navigate to Installation Settings and press "OK".

STEP 4    

Enter your PIN to access this setting. (Default PIN is 0000).

STEP 5    

Navigate to Restore Factory Settings and press "OK".

STEP 6    

Navigate to Yes, continue and  press "OK" to  confirm your selection.    

Otherwise, navigate to No, go back to maintain the settings.

STEP 7    

Please reboot your box.

STEP 8    

New Installation Settings screen will appear.    

Click here to follow New Installation Settings guide.

You will be able to access Netflix on your Ultra and Ulti Box. However, kindly note that if you have an Ulti Box with a Netflix Premium subscription, you will not be able to watch content in 4K UHD and Netflix Spatial Audio.

1. Please use a LAN ethernet cable and connect your computer/laptop to the back of the Maxis Router.

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox, etc.

3. On the address bar, please go to http://192.168.1.254 and the page below will appear.

    The default login of the router as below. If you have done a configuration on your router and changed your password previously, please use the password you have previously set.

    Username: administrator

    Password: Router S/N (Available on the sticker at the back of the router)

4. Once you have successfully login, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi Configuration to configure the Wi-Fi parameters.

6. You may change the Wi-Fi Name and the Password to follow your preferences, then click "Save" for the changes to take place.

Please reconnect to the new wireless name with the new password once completed.

You will regain access to your channels on Astro immediately once the equipment has been installed at your new house, provided your account is active. Customers can still enjoy viewing via Astro Go.

Astro GO+ is a service add-on that: 

• Enables the simultaneous viewing of Astro GO for up to 4 users/devices. 
• Increases the cloud recording storage from 200 hours up to 1500 hours. 

Refund  can be made when there be a termination of account, over payments and in  cases where payment was wrongly made to another Astro account.

Disabling band steering means that there will be two frequency bands available for the users - 2.4GHz and 5GHz.
 

Note: Band Steering is called Dual-band Combination in the router web interface.
 

1. Please connect your computer or laptop to your Astro Fibre router using LAN cable. Your LAN cable must be connected from the yellow port of Astro Fibre router (Any available port).
2. Once connected, open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, type http://192.168.100.254 and below page will appear.

Login using your username and password if you have changed the router login setting. Otherwise, your default router login is as per below.

Username: user
Password: user
 

4. Once you have successfully logged in, the router's web-based setup page will appear.

5. At the top of the page, click Wi-Fi to configure the WiFi parameters.

6. Click on Dual-band Combination button to disable the Band Steering.

7. Set the Wi-Fi name and Wi-Fi Password for both 2.4GHz and 5GHz bands based on your preference. Then click "Apply" for the changes to take place.

8. Kindly ensure to reconnect your WiFi according your new WiFi name and password.

You can make changes to your Netflix plans that are included in your Bundle through My Astro app 

You can change your non Astro-bundled a-la carte Netflix plan at any time by signing into Netflix.com and visiting the Account page, then selecting Change Plan to view and select available plans.  

No, customers are only allowed to choose ONE billing option (either Paper Bill or E-bill or SMS bill). However, customers who opted for Paper Bill will still be able to check their bills through Astro Self-Service Portal, IVR, Channel 200 and WhatsApp.

Yes, you will need to pay additional RM25 per remaining contract months per unit on top of the standard Broadband penalty fee should you terminate the contract within 24 months.

You will receive SMS notifications upon successful sign-up with a delivery tracking number for the Plug & Play Box and the Astro SIM card.

Currently the Multiroom (Smart TV) app is supported on four (4) brands with the software version listed below:

1. Sharp
2. Sony
3. LG
4. Samsung

Only new and existing Astro Fibre customers with the latest RG21 router can use the Astro Fibre app.

Your current additional RM20 rebate will be removed. However, you will still get to enjoy the standard bundle rebate accordingly.  

About the WeTV app

1. What is WeTV?

WeTV is a global video on demand and over-the-top streaming service, providing the best premium entertainment including Chinese, Indonesian, Korean, Thai, Japanese and Malaysian series and movies to fans of Asian entertainment.

2. Can I stream WeTV for free on my Ultra/Ulti Box?

All Ultra/Ulti Box customers may watch selected WeTV titles for free on their Astro Box.

Simply follow these steps:

Step 1: Go to your Ultra/Ulti Box Home Page and select “WeTV” under the Apps rail

Step 2: Click play on any non-VIP titles/episodes and start streaming!

Note: No login is required to stream free content on WeTV.

3. How can Astro customers enjoy WeTV?

Astro customers can subscribe to WeTV VIP via Astro as an add-to-bill service for only RM10.50/month (RRP RM11.90) to enjoy the app on their big screen TV via the Ultra/Ulti Box, wetv.vip or on the go with the WeTV mobile app which is available on Android and iOS devices.

For more details on the WeTV VIP Membership, please refer to Q12 - Q17.
 

4. How do I subscribe to WeTV VIP via Astro?

All new and existing Astro TV customers can subscribe to WeTV VIP for only RM10.50/month by following the steps below:

Step 1: Go to www.astro.com.my/WeTV and select “Get WeTV now”

Step 2: Log in with your Astro ID

Step 3: Key in your mobile number and proceed to add WeTV to your bill

Step 4: Once you have validated your mobile number via the OTP code, you will be able to enjoy VIP-exclusive shows on WeTV!

5. How do I access WeTV VIP on my Ultra/Ulti Box?

After completing the subscription process in Q4, follow the simple steps below to access WeTV VIP on your Ultra/Ulti Box:

Step 1: Go to your Ultra/Ulti Box Home Page and select "WeTV" under the Apps rail

Step 2: Click "Log in" and scan the QR code on your TV with your mobile device to download/launch the WeTV app

Step 3: On your mobile device, create a new account or log in using your registered mobile number and click "Login Authorization" to pair your device to your TV

Step 4: Once pairing is complete, please press the back button on your remote to start enjoying VIP-exclusive shows!

Important note: Please ensure that the mobile number used to log in to the app is the same one used to purchase your WeTV VIP subscription. Email login is not applicable for Astro Billing WeTV VIP customers.

*We highly encourage our customers to only use their device’s built-in camera to scan the QR code if available. Alternatively, only use QR code scanner apps that are from a trusted 3rd party provider. By using an untrusted QR code scanner app, you assume all responsibility for any damages or losses that may occur.

6. I already have a WeTV subscription, what will happen if I use the same mobile number to subscribe to WeTV VIP via Astro?

If you already have a WeTV subscription, you are allowed to subscribe to WeTV VIP with the same mobile number via Astro; however, your existing account will continue to run until you manually cancel it. With two active subscriptions with the same mobile number, your subscriptions will be added on top of your existing account and you will be charged twice on two separate accounts.

7. Can I access the WeTV app outside of Malaysia?

Yes, you will still be able to access the WeTV app and stream your favourite content outside of Malaysia. However, kindly be informed that this will be subject to content availability in the specific regions.

8. Can I download content on the WeTV app for offline viewing?

Yes, you can download WeTV's content on your device for offline viewing if you have subscribed to WeTV VIP. This feature is not available if you are not a VIP member. However, kindly note that some content is subjected to copyright which disables the download function on those selected videos.

9. What is the storage requirement for content downloading?

The storage requirement is dependent on the type of videos users are downloading as the space needed varies between titles.

10. How many devices can I use to stream WeTV at the same time?

You can access your WeTV VIP account on up to 2 devices at a time, including your Ultra/Ulti Box. To ensure a smoother streaming experience, please sign out from any unused devices.

11. Are there any subtitles available for the content on WeTV?

Yes, subtitles are available in various languages including English, Malay, Chinese (Simplified & Traditional) etc.

To enable this feature, click on the subtitles selection option at the bottom right corner of the video player, then click on the language you desire.

WeTV VIP Subscription

12. What is a WeTV VIP subscription?

WeTV offers a wide range of hot and exclusive content in advance for WeTV VIP members, which includes WeTV Originals, series, dramas and many more. With a VIP subscription, you can also enjoy all these exciting content with the ability to skip advertisements to stream without interference and watch your favourite shows on two devices at the same time!

VIP membership privileges:

1. Premium Content on WeTV only

2. Enjoy VIP content on two devices at the same time

3. Watch the content in advance before anyone else!

13. Can I rent movies or series on WeTV via Astro?

Yes, you will be able to rent titles on the WeTV mobile app. Subsequently, you will be able to stream your rented title on the Ultra/Ulti Box, wetv.vip, and the mobile app.

14. How much does a WeTV VIP subscription via Astro cost?

Astro customers can enjoy a special offer of RM10.50/month (RRP RM11.90/month) when they subscribe to WeTV VIP via Astro.

Note to CCC: Employee/Ex Employee/Courtesy Board Members will also enjoy the same pricing at RM10.50/month.

15. When can I start enjoying my WeTV VIP subscription?

You will be able to enjoy all the content on WeTV via your Ultra/Ulti Box, wetv.vip and the WeTV mobile app immediately upon successful purchase from the Astro website. Please ensure that the mobile number used to log in to the app is the same one used to purchase your WeTV VIP subscription.

16. How do I cancel my WeTV VIP subscription?

You can cancel your WeTV VIP subscription via WeTV’s official website or mobile app.

Kindly note that we will not be able to offer a refund if you do decide to leave the WeTV app before your subscription period ends.

17. Will there be any penalty fees if I cancel my WeTV VIP subscription?

No, your subscription will be terminated at the end of your Astro billing date. Until then, you will still be able to access your WeTV VIP account.

App Issues

18. Who may I contact if I encounter any problems with the WeTV app?

If you require any assistance with the app, you may:

1. Visit the WeTV official Facebook Page for more information: WeTV Malaysia - Home | Facebook; or

2. Drop the WeTV team a message via Facebook chat here

If you encounter any issues with your Astro billing and entitlement, you may contact our Customer Service by:

1. Submitting a feedback form here: www.astro.com.my/contactus/form; or

2. Reaching to us via WhatsApp by typing "Hi"at 03-9543 3838

19. Will my personal information be protected?

Yes, Astro is bounded by the PDPA. All information received will be used in accordance with our Privacy Notice

Intermittent internet connection using LAN cable

Looks like there is something wrong with your service connection.

Please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please ensure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Intermittent internet connection using Wi-Fi

1. Router Positioning
   Most people underestimate the importance of picking a good spot for a Wi-Fi router. Even a small shift in positioning could end up being the difference between day and night.
   
    i) High vs. Low
   Put the router as high up as possible to extend the broadcasting range of the radio waves. This also helps clear the router of possible interferences.
   
   ii) Concrete & Metals
   Make sure your router isn't blocked by any other objects, especially devices that are electronic. Also, avoid placing your router in your basement as this area is usually enclosed by a lot of concrete, which can be almost impossible for Wi-Fi signals to penetrate.
   
   iii) Distance to Router
   The further away from your router you get, the weaker the Wi-Fi signal. Therefore, the best option is to place your router as close to your devices as possible, but this is only practical if you have one main area where you tend to use your devices.
   
   Otherwise, you should place your router near the center of your home. After all, Wi-Fi broadcasts in 360 degrees, so it doesn't make sense to put it at one end of the house.
   
    

2. Wireless Interference & Noise
   You've probably never noticed but there are wireless signals all around you wherever you go and they're passing through you all the time. From where? Electronic devices, Wi-Fi routers, satellites, cell towers, and more.
   
   Although Wi-Fi is supposed to be on a different frequency than most of these devices, the amount of radio noise can still cause interference. Some common causes of interference include:
   i) Microwaves
   ii) Bluetooth Devices
   iii) Cordless Phone
    

3.  Surrounding Wi-Fi signals
   A truth of the modern world is that every household has their own Wi-Fi network, which can cause issues with channel  overlap. This can be somewhat problematic in a townhouse, but is especially problematic in housing complexes and apartments where there can be many  routers within close proximity. Which is why it's important that you pick a good channel in your router settings. Modern routers can choose channels for you automatically, but sometimes it's better to investigate and find the best channel yourself.

4. Usage
   More likely, however, is that the people on your network such as friends, roommates, or family members are participating in bandwidth-heavy activities like gaming and streaming Ultrabox/Netflix.
   Fortunately, if this is the case, you can prioritize your own network traffic by enabling Quality of Service in your router settings.

If the problem persists, please run a Ping Test, Traceroute Test and attach the picture or screenshot of both test results in the Feedback Form below, in order for us to provide further assistances.

Please make sure to attach the required screenshot(s) in ONE file (i.e. Microsoft Word document, PDF, Image file) before submitting the form.

Quick Info
A Ping Test shows how long it takes for packets to reach host.
A Traceroute Test traces the route of packets to destination host from our server.

By adding a Netflix account to your Astro bill, your Netflix account is already activated. No additional steps for activation are required.

STEP 1

Switch off the power for your box and  make sure that the adapter's power light is off.

STEP 2

Locate the Smartcard at the front or right side and gently pull it out.

Make sure that the adapter's power light is off.

STEP 3

Wipe the Smartcard's gold chip clean using a dry soft cloth.

STEP 4

Make sure the gold chip is facing upwards and reinsert it all the way in.

STEP 5

Switch on the power for your box and make  sure that the adapter's power light is on. Please wait for 5 minutes.

STEP 6

Turn on your box. You should no longer be experiencing this problem.

If issue persist, please submit the issue on our Feedback Form and attach a picture of your smart card number for assistance.

There will be no penalty imposed upon the removal of Astro GO+ from your subscription.

For customers with Entertainment Plus, Movies Plus, Sports Plus, Premium 2, Premium 3, and Platinum Pack 

1. Launch Netflix from the home screen or via remote control. 

2. Click on Get Started

3. If you are an existing Netflix customer, please fill in the email address and password associated with your Netflix account. Once successfully completed, all existing settings and watching history on your Netflix account will be brought over. If you are a new Netflix customer, create a new account by filling in your email address and a password for your new Netflix account. 

4. In the next screen, you will be shown your default Netflix package “Standard”, you can choose to upgrade to “Premium” here. 

5. The final screen provides a summary of your account including your email. Click Start Watching to enjoy Netflix on your Ultra/Ulti Box. 

‍

For Non-Entertainment Plus, Premium 2, Premium 3, and Platinum Pack Pack customers (New Netflix customers) 

1. Launch Netflix from the home screen or via remote control.

2. Click on Join Now

3. Create a new account by filling in your email address and a password for your new Netflix account. 

4. The final screen provides a summary of your account including your email. Click Start Watching to enjoy Netflix on your Ultra/Ulti Box. 

Note: The Netflix plan will be defaulted to Premium, you may select ‘Change Plan’ to choose the ‘Standard’ plan. 

‍

For Non-Entertainment Plus Pack, Premium 2, Premium 3, and Platinum Pack customers (Existing Netflix customers) 

1. Launch Netflix from the home screen or via remote control 

2. Click on Sign-in 

3. If you are an existing Netflix customer, please fill in the email address and password associated with your Netflix account. 

4. You will be able to start watching Netflix on your Ultra/Ulti Box once you log in.

The all-new Astro Fibre is Astro's own internet service whereby customers would be able to enjoy the Astro content over the internet via wireless connection along with high-speed internet service ranging from 50Mbps - 800Mbps.

While Astro & Broadband offers Astro content in partnership with Maxis Fibre Broadband or Allo City Broadband for customers to enjoy the best entertainment through Astro while staying connected with high-speed internet.

You may proceed with the following troubleshooting steps and it shouldn’t take you much longer  than 15 minutes.

1. Please standby a computer/laptop to access to the internet and connection must be via LAN cable (connect the LAN cable to the Black port at D-Link Router and direct to the computer/laptop).    

2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.    

3. On the address bar, please go to tplinkwifi.net and to access to below login page. Type the Username and Password, then click "Login".

The default login of the router is available on the sticker at the back of the router. If you have done a configuration on your router previously, the password may be  different)

For example, below is the login details of the above router:

Username: admin

Password: TIMECE24

4. Once you have successfully login, the router's web-based setup page will appear. Please follow below steps for the configuration.

5. From the top menu, choose Basic and then click Wireless tab on the left menu to access to below screen.

6. Since this is a dual band router, you will have 2 Wireless Network Names  (SSID) i.e. 2.4GHz and  5GHz. You may connect to any of the SSID, preferably with a stronger signal available.

7. You may change the Wireless Network Name (SSID) and the Password to follow your preferences, then click "Save"  for the changes to take  place.

Please reconnect to the new wireless name with the new password once completed.

‍

This Disney+ Hotstar software update will be rolled out progressively to all Ulti Box customers starting 23 August 2022. Please be assured that you will be able to access the Disney+ Hotstar app on your Ulti Box soon. 

If you need further assistance, please call our Customer Contact Centre or WhatsApp "DH Help

No, eligible customers will not be charged for this speed upgrade. Your speed plan will be upgraded automatically for 24 months, depending on your subscription. After the FREE speed upgrade period, your Astro Fibre plan will return to its regular speed.
 

You will receive an email within 45 minutes of payment made to let you know whether your advance payment is successful or not. If your payment has failed, you may call Astro's Contact Centre at 03-9543 3838 or wait for an Astro representative to be in contact with you within 2 working days to assist you with your order.

From 8 October 2021 onwards, Astro will be ceasing the daily passes (e.g. 3, 5, 7 & 30 days passes). Please subscribe to the relevant packs to continue enjoying your favourite content. Stay tuned for more exciting offers. Thank you.

Astro is continuously improving our user interface and introducing new features to our platforms to ensure that your Astro experience is more seamless, efficient and user-friendly.

For details on our latest interface, Picture-in-Picture mode and auto-start interactive mode on Astro GO, please click here.

In addition, we have also recently introduced a new look to the Title Information Page, the ability to disable the Profile Selection Screen and adjustable auto-standby timing. For more information, please click here.

Please contact Astro Customer Call Center via 03-95433838

You may proceed with below troubleshooting and it shouldn't take you any longer than 15 minutes.

1. Please standby computer/laptop to access to the internet and connection must be via LAN (cable) [Connect the LAN (cable) to the yellow port at ZTE Router and direct to computer/laptop].
2. You may open any web browser such as Google Chrome, Internet Explorer, Mozilla Firefox and etc.
3. On the address bar, please go to http://192.168.0.1 and below page will appear.

4. Type the Username and Password as below. Then click Login. (These are the defaults, if you have done previous configuration on your router the password may be different)
 

Username: admin
Password: admin (or time123)

 

5. The router's web-based setup page should now appear. Please follow below steps for the configuration.

• On the setup page, click the Network tab then click on the WLAN then choose Basic sub-tab

• Please ensure Wireless RF Mode is Enabled.

• Click the drop-down arrow for Channel, then select your desired channel.
• Choose between 1 until 11 (Suggested 1,6,11).

• Click Submit. Router will auto reboot and connection re-establish after few minutes.

Option 1

1. Please turn off  all devices (Modem and Router). By restarting your modem, you can isolate the  possibility of overloaded processes in the modem, which would impact its  performance.
2. Ensure both cables on Modem (LAN Port  1) and Router (Internet Port) are properly connected.
    

Modem connection

Router connection

3. Please make sure the LAN cable is connected properly from router (Port 1-4 - LAN port) to PC/ Laptop.

4. If you have change the password in Selfcare Time portal recently,  please change the router configuration follows the new password made in Selfcare, but if you didn't make any changes, please go to Step 5.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.

Option 2/ Option 3

1. Please turn off all devices (Modem and  Router). By restarting your modem, you can isolate the possibility of overloaded processes in the modem, which would impact its performance.
2. Gently remove fiber optic cable and blow / wipe the tip of the fiber cable. This is to clean up the cable in order to avoid any interferences.
3. Re-insert the fiber cable to the optical port behind the modem.
4. Ensure both cables on Modem (LAN Port 1) and Router (Internet Port) are properly connected.

Modem Connection

Router Connection

5. Make Sure both cables on Modem (LAN Port 4/ LAN Port 3 for second decoder) and Astro Decoder (Network Port) are properly inserted.

6. Switch on modem and router and please wait for 2 minutes to stabilise the devices after reboot.

5. If the issue persists, submit your feedback form and attach your modem light indicator picture/video for further assistance.
 

Option 4

1. Ensure Modem/Router are connected tightly to the power socket.

2. Try to use another power socket / power source to eliminate faulty power sockets/power sources which  could cause the issue.

3. If the issue persists, submit your feedback form for further assistance.


Option 5

1. Please ensure LAN cable is directly connected to modem port LAN 1.

2. Please use different LAN port if LAN 1 port is still off / not working.

3. If the issue persists, submit your feedback form for further assistance.

Yes, as part of our Astro Fibre Movies & Sports Campaign, new Astro Fibre customers can enjoy 50Mbps + the Movies/Movies+/Sports/Sports+ Pack TV bundle for a special price from only RM164.99/month when they sign up within the campaign period, with more than RM800 savings in total.

If you would like for more information, kindly visit our Multiroom page via Astro website https://www.astro.com.my/multiroom

To view the terms and conditions, click here.

Connect your PVR to Wi-Fi and enjoy access to our library of Video On Demand. Replay old seasons, catch-up latest episodes of your favourite shows, anytime you want. To connect your PVR, follow the steps below depending on your box type:

(a) Wi-Fi Enabled PVR (DMT5)

·      Press the “Home” button and select “Settings” > “Network” > “Wi-Fi”

·      Allow the PVR to scan Wi-Fi networks available and subsequently choose your home Wi-Fi network > Enter your Wi-Fi password if required

·      Once connected, the icon below will appear on the screen.

‍
      Tip: Use the alpha-numeric keyboard on your Astro Remote to key in your password

·      Press the “Home” button and select “On Demand” to start watching videos on demand!

‍

(b) Non-Wi-Fi Enabled PVR (HD PVR)

There are two ways to connect your HD PVR decoder to your home Wi-Fi
(i) Using the Ethernet (LAN) cable 
 

·       Plug in the LAN cable from your modem into the PVR network port

·       Once connected, the icon below will appear on the screen

·       Press the “Home” button and select “On Demand” to start watching videos on demand!

(ii) Using an Astro Wi-Fi dongle as per shown below

Step 1 - Plugin the Wi-Fi dongle into the front USB part of your PVR decoder.

Step 2 - A prompt will appear stating "Do you wish to connect to a wireless network?", select "Yes, continue."

Step 3 - Once connected, the Wi-Fi icon will appear on the screen. Now you are ready to download and enjoy Astro's on demand entertainment.

Step 4 - Press the “Home” button and select “On Demand” to start watching videos on demand!

*The Wi-Fi dongle is only applicable for the non-Wi-Fi enabled PVR (as per the picture).

Please provide your primary mobile number via My Astro Portal, or send it to one of our platforms found here.

Note:

• Any changes of contact details to be requested by account holder only.
• Only account holder's contact to be updated as primary mobile number in the system.

No, you will not be charged 8% Service Tax for paper billing option.

There will be no installation fee for both Astro Box and Ultra Box. The Multiroom (second decoder) must be installed at the same registered address as your primary subscription.

Please note that only one Disney+ Hotstar access is bundled to each TV Pack subscription which allows two concurrent streams on Disney+ Hotstar. 

If you would like to upgrade your pack to include Disney+ Hotstar Premium, please contact Astro Customer Contact Centre at 03 9543 3838. Alternatively, please WhatsApp Astro at 03 9543 3838 and type DH Help for further assistance. 

STEP 1  

On your remote, press the “HOME” button and the home menu will be displayed at the bottom of your screen.

STEP 2    

Navigate to SETTINGS and press “OK”.

STEP 3  

Navigate to STB DIAGNOSTICS and press “OK”.

STEP 4    

Refer to the signal strength % shown on the top left of your screen.